need help iOCEAN X7 - GSM-Forum

students · 09-19-2015, 17:12

log info
Info read not done Erased phone or unsupported FlashIc?

Code:

 [eMMC] : FLASH_LEN : 0x00000000E7000000
INT RAM    : 0x00020000
EXT RAM    : 0x40000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Error read initial info , blank flash or wrong settings?

Operation Failed
Elapsed: 00:00:12

Reconnect Power/Cable!


Operation : Check / Read Info [ v1.30 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 124 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 204A0190594E49588DA116481B20BA8C
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ... 
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0090 , OEM : 014A
[eMMC] : FLASH_INF : HYNIX
[eMMC] : FLASH_CID : 90014A2058494E594816A18D8CBA201B
[eMMC] : FLASH_EXT : 00200000/00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
INT RAM    : 0x00020000
EXT RAM    : 0x40000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Info read not done :( Erased phone or unsupported FlashIc?

Done!
Elapsed: 00:00:11
Reconnect Power/Cable!


Operation : Check / Read Info [ v1.30 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 69 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0x05
BLVersion : 0xFE
Preloader Status : Not active (Erased)
Processing DA stage
DA Select done , sending 
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 204A0190594E49588DA116481B20BA8C
DA Stat : v3.2 on BBID : 0x86
DRAM not initialized , configure DRAM Settings
DRAM EmiReq Ok , 0x00B8

Error : DA init Failed! Error code : 0x5
LErr : EMICFG_NOT_FOUND

Boot Error!

Operation Failed
Elapsed: 00:00:09
Reconnect Power/Cable!


Operation : Check / Read Info [ v1.30 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 124 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 204A0190594E49588DA116481B20BA8C
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ... 
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0090 , OEM : 014A
[eMMC] : FLASH_INF : HYNIX
[eMMC] : FLASH_CID : 90014A2058494E594816A18D8CBA201B
[eMMC] : FLASH_EXT : 00200000/00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
INT RAM    : 0x00020000
EXT RAM    : 0x40000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Info read not done :( Erased phone or unsupported FlashIc?

Done!
Elapsed: 00:00:12
Reconnect Power/Cable!

Format FileSystem [ v1.30 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 124 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 204A0190594E49588DA116481B20BA8C
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0090 , OEM : 014A
[eMMC] : FLASH_INF : HYNIX
[eMMC] : FLASH_CID : 90014A2058494E594816A18D8CBA201B
[eMMC] : FLASH_EXT : 00200000/00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Error read initial info , blank flash or wrong settings?

Operation Failed
Elapsed: 00:00:10
Reconnect Power/Cable!

JayDi · 09-19-2015, 17:22

Find firmware for it and flash first.

students · 09-20-2015, 08:48

Quote:

Originally Posted by JayDi

Find firmware for it and flash first.

starting iOCEAN X7 hang on logo
Flash by tools = dead
firmware read = Infinity-Box starting iOCEAN X7 hang on logo
iOCEAN X7 preloader and scatter_emmc read = InfinityBox CM2MTK.rar

Code:

 http://www.mediafire.com/download/c7vqgeqw9tqsyre/preloader+and+scatter_emmc+read+%3D+InfinityBox+CM2MTK.rar

llog flash firmware read = Infinity-Box

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 124 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 204A0190594E49588DA116481B20BA8C
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0090 , OEM : 014A
[eMMC] : FLASH_INF : HYNIX
[eMMC] : FLASH_CID : 90014A2058494E594816A18D8CBA201B
[eMMC] : FLASH_EXT : 00200000/00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6589 , Project : MTK6589 , Storage : eMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000000600000-0x0000000000100000
Erase : 0x0000000002720000-0x0000000092C60200
Flash Pre-Erase Done, time used : 00:00:06

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_vanzo89_wet_jb2.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : FFFFFFFF
PartErr : Not initialized , will update PMT now ...
Repartition Failed! Break! Something wrong with HW or BL (FirmWare)

Done!
Elapsed: 00:00:26
Reconnect Power/Cable!

JayDi · 09-20-2015, 09:38

Error says about damaged eMMC.
Try erase whole flash then flash again. If nothing changed - then HW.

students · 09-21-2015, 04:27

Quote:

Originally Posted by JayDi

Error says about damaged eMMC.
Try erase whole flash then flash again. If nothing changed - then HW.

log
log erase done
Chinese Miracle II [MTK module] v 1.30

Operation : Flash Erase [ v1.30 ]
User accepted Flash Erase operation!

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 124 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 204A0190594E49588DA116481B20BA8C
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0090 , OEM : 014A
[eMMC] : FLASH_INF : HYNIX
[eMMC] : FLASH_CID : 90014A2058494E594816A18D8CBA201B
[eMMC] : FLASH_EXT : 00200000/00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Erase Flash now ...
Keep Preloader alive
Flash erase done

Done!
Elapsed: 00:00:26
Reconnect Power/Cable!

sneha · 09-21-2015, 04:35

Erase Flash now ...
Keep Preloader alive
Flash erase done

untick on keep preloader alive then erase

then try init preloader

students · 09-21-2015, 07:52

log Flash
pin 100%
Chinese Miracle II [MTK module] v 1.30

Scatter Load Ok , BaseBand : MT6589 , Project : MTK6589 , Storage : eMMC
Files found : 13 , Set to Flash : 12
Ready to Flash!

Scatter Load Ok , BaseBand : MT6589 , Project : MTK6589 , Storage : eMMC
Files found : 13 , Set to Flash : 12
Ready to Flash!

Operation : Flash [ v1.30 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 69 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0x05
BLVersion : 0xFE
Preloader Status : Not active (Erased)
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 204A0190594E49588DA116481B20BA8C
DA Stat : v3.2 on BBID : 0x86
DRAM not initialized , configure DRAM Settings
DRAM EmiReq Ok , 0x00B8
DRAM Init Ok , 0x40000000
DA Sent. Configure setting now ...

DA start Failed at final stage!
Check battery , cable , drivers and try try again

Boot Error!

Operation Failed
Elapsed: 00:00:30
Reconnect Power/Cable!

JayDi · 09-21-2015, 07:55

Open phone and fix hardware first. Then return to flashing.

09-19-2015, 17:22	#2 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	Find firmware for it and flash first.

09-20-2015, 09:38	#4 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	Error says about damaged eMMC. Try erase whole flash then flash again. If nothing changed - then HW.

09-21-2015, 04:35	#6 (permalink)
sneha No Life Poster Join Date: Aug 2006 Location: BHARAT Posts: 3,076 Member: 327043 Status: Offline Sonork: 100.1587811 Thanks Meter: 1,514	Erase Flash now ... Keep Preloader alive Flash erase done untick on keep preloader alive then erase then try init preloader

09-21-2015, 07:52	#7 (permalink)
students No Life Poster Join Date: Jun 2010 Location: việt nam Posts: 1,912 Member: 1327392 Status: Offline Thanks Meter: 409	log Flash pin 100% Chinese Miracle II [MTK module] v 1.30 Scatter Load Ok , BaseBand : MT6589 , Project : MTK6589 , Storage : eMMC Files found : 13 , Set to Flash : 12 Ready to Flash! Scatter Load Ok , BaseBand : MT6589 , Project : MTK6589 , Storage : eMMC Files found : 13 , Set to Flash : 12 Ready to Flash! Operation : Flash [ v1.30 ] ======= Flash 1. Power Off Phone , Remove battery , Insert back 2. Insert USB cable. In some cases require hold BootKey Wait for phone... Phone found! [ 69 ] Sync... Inital regs read done Boot Info : BB_CPU_ID : 6583 BB_CPU_HW : CA01 BB_CPU_SW : 8A00 BB_CPU_SB : 0001 BB_CPU_NM : [MediaTek] MT6583\|6589_S00 Processing BROM stage SecCfgVal : 0x00000000 BromVersion : 0x05 BLVersion : 0xFE Preloader Status : Not active (Erased) Processing DA stage DA Select done , sending DA Ver : MTK_AllInOne_DA_v7.1533.03 NAND_ID : 00000000000000000000000000000000 eMMC_ID : 204A0190594E49588DA116481B20BA8C DA Stat : v3.2 on BBID : 0x86 DRAM not initialized , configure DRAM Settings DRAM EmiReq Ok , 0x00B8 DRAM Init Ok , 0x40000000 DA Sent. Configure setting now ... DA start Failed at final stage! Check battery , cable , drivers and try try again Boot Error! Operation Failed Elapsed: 00:00:30 Reconnect Power/Cable!

09-21-2015, 07:55	#8 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	Open phone and fix hardware first. Then return to flashing.