need help micromax D321 - GSM-Forum

parth gupta · 03-09-2017, 14:09

Dear infinity team

How to solve this problem

Micromax d321 hang on android logo i flashed the phone same firmware but problem same hang on android logo

princesaddam · 03-09-2017, 14:20

Hello,
Test Emmc R/o maybe ur emmc is in Read only state,,, post logs after test

parth gupta · 03-09-2017, 15:08

Operation : HW Test [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 6 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164040501A2A7A43231
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164040501A2A7A43231
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID : 0xE3BC67B82A464EF42F500118532A4186
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Processing Miscellaneous test
MSC : BatteryLevel : 3528 mV

[Processing] FlashMemory Read-Write test
[eMMC] : [HYNIX] , d1G4 , 0xE9000000 , 3728 MiB
[eMMC] : CID : 90014A4834473164040501A2A7A43231

[eMMC] : MODE : SQ-WR
[PASSED] : eMMC RW Check #1 Ok!
[eMMC] : MODE : RA-WR
[PASSED] : eMMC RW Check #2 Ok!

[eMMC RO CHECK] : eMMC Ok! READ-WRITE Passed!

[Processing] RAM Read-Write test
[DRAM] : 0x20000000 , 512 MiB

[DRAM] : ADDRESS BUS test
[PASSED] : Bus Count : 0x1C
[DRAM] : DATA BUS test
[PASSED] : Bus Count : 0x1F
[DRAM] : PATTERN test
[PASSED] : PATTERN Ok
[DRAM] : INCDEC test
[PASSED] : INCDEC Ok

All Done!

Done!
Elapsed: 00:01:32
Reconnect Power/Cable!

PASSIONATE_BOYS · 03-09-2017, 15:34

Hello,
Phone stuck on recovery mode or on logo?
If stuck on recovery mode even after flash check hardware (volume keys etc).
If stuck on logo then erase flash first and flash again.
Remember to flash with same version written on back label.

Br.
Infinity Box Team.

03-09-2017, 14:09	#1 (permalink)
parth gupta No Life Poster Join Date: Jan 2009 Location: india Posts: 885 Member: 942210 Status: Offline Sonork: 1511 Thanks Meter: 91	need help micromax D321 Dear infinity team How to solve this problem Micromax d321 hang on android logo i flashed the phone same firmware but problem same hang on android logo

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-09-2017, 14:20	#2 (permalink)
princesaddam No Life Poster Join Date: Apr 2009 Location: Inside Infinity Posts: 1,688 Member: 1010626 Status: Offline Sonork: using fb Thanks Meter: 735	Hello, Test Emmc R/o maybe ur emmc is in Read only state,,, post logs after test

03-09-2017, 15:08	#3 (permalink)
parth gupta No Life Poster Join Date: Jan 2009 Location: india Posts: 885 Member: 942210 Status: Offline Sonork: 1511 Thanks Meter: 91	Operation : HW Test [ v1.58 ] 1. Power Off Phone , Remove battery , Insert back 2. Insert USB cable. In some cases require hold BootKey Wait for phone... Phone found! [ 6 ] Sync... Inital Boot Ok! BB_CPU_PID : 6572 BB_CPU_NME : [MediaTek] MT6572_S00 BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000 Processing BROM stage Settings for BROM configured! SecCfgVal : 0x00000000 BromVer : 0x00FF BLVersion : 0x0001 PreLoader : Active [ Boot with PL ] BootLdrSS : NORMAL with PRELOADER Processing DA stage DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07 Sending and initialize DA ... Running DA ver.4.2 on BBID : 0x88 NAND Flash : NOT INSTALLED eMMC Flash : 90014A4834473164040501A2A7A43231 Initialize Memory ... DRAM already initialized by Preloader DAgent sent , init HW now eMMC FlashIC initialized [eMMC] : FLASH_VEN : 0x90 , OEM : 014A [eMMC] : FLASH_INF : [HYNIX] , d1G4 [eMMC] : FLASH_CID : 90014A4834473164040501A2A7A43231 [eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000 [eMMC] : FLASH_LEN : 0x00000000E9000000 [eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB] DEV RID : 0xE3BC67B82A464EF42F500118532A4186 INT RAM : 0x00020000 EXT RAM : 0x20000000 [512 MiB] BOOT TYPE : EMMC_FLASH_BOOT SOC VERIFY : C1 Boot Ok! Processing Miscellaneous test MSC : BatteryLevel : 3528 mV [Processing] FlashMemory Read-Write test [eMMC] : [HYNIX] , d1G4 , 0xE9000000 , 3728 MiB [eMMC] : CID : 90014A4834473164040501A2A7A43231 [eMMC] : MODE : SQ-WR [PASSED] : eMMC RW Check #1 Ok! [eMMC] : MODE : RA-WR [PASSED] : eMMC RW Check #2 Ok! [eMMC RO CHECK] : eMMC Ok! READ-WRITE Passed! [Processing] RAM Read-Write test [DRAM] : 0x20000000 , 512 MiB [DRAM] : ADDRESS BUS test [PASSED] : Bus Count : 0x1C [DRAM] : DATA BUS test [PASSED] : Bus Count : 0x1F [DRAM] : PATTERN test [PASSED] : PATTERN Ok [DRAM] : INCDEC test [PASSED] : INCDEC Ok All Done! Done! Elapsed: 00:01:32 Reconnect Power/Cable!

03-09-2017, 15:34	#4 (permalink)
PASSIONATE_BOYS No Life Poster Join Date: Jul 2007 Location: Infinity-Box Support- Posts: 9,321 Member: 541591 Status: Offline Sonork: 100.1611509 Thanks Meter: 7,361	Hello, Phone stuck on recovery mode or on logo? If stuck on recovery mode even after flash check hardware (volume keys etc). If stuck on logo then erase flash first and flash again. Remember to flash with same version written on back label. Br. Infinity Box Team.