GSM-Forum - Never Repair IMEI on MTK Phones

GSM-Forum (https://forum.gsmhosting.com/vbb/)

- Infinity-Box (https://forum.gsmhosting.com/vbb/f296/)

- - Never Repair IMEI on MTK Phones (https://forum.gsmhosting.com/vbb/f296/never-repair-imei-mtk-phones-1998229/)

Never Repair IMEI on MTK Phones

Where is the problem i cant repair IMEI on MTK Phones

All Ways i am getting same Log
In this case its MTK6589

Phone Info

Quote:

Operation : Check / Read Info [ v1.21 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 19 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 4D0001703430434DD90602475D30A4B8
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0070 , OEM : 0100
[eMMC] : FLASH_INF : G40CM
[eMMC] : FLASH_CID : 7001004D4D433034470206D9B8A4305D
[eMMC] : FLASH_LEN : 0x00000000E2C00000
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand : MTK/6589
ProdName : PhonePadDuo
ProdModel : M-PP2S500
Device : PhonePadDuo
AndroidVer: 4.2.1
MTKxCPU : MT6589
MTKxPRJ : ALPS.JB2.MP.V1.2

Done!
Elapsed: 00:00:22
Reconnect Power/Cable!

IMEI Repair

Quote:

Card found: S/N CB82:0128
Chinese Miracle II [MTK module] v 1.21

Operation : Repair Security [ v1.21 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 19 ]
Sync...
Device boot not done
Check Drivers
Try again

Init Service mode failed, something went wrong :(

Reconnect Power/Cable!

Operation : Repair Security [ v1.21 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 19 ]
Sync...
Device boot not done
Check Drivers
Try again

Init Service mode failed, something went wrong :(

Reconnect Power/Cable!

Quote:

Operation : Fix Unknown BaseBand [ v1.21 ]
User accepted FixBB operation!

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 19 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 4D0001703430434DD90602475D30A4B8
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0070 , OEM : 0100
[eMMC] : FLASH_INF : G40CM
[eMMC] : FLASH_CID : 7001004D4D433034470206D9B8A4305D
[eMMC] : FLASH_LEN : 0x00000000E2C00000
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Step #1
Step #1 ... Ok
Step #2
Step #2 ... Ok
Reset Done!

Done!
Elapsed: 00:00:20
Reconnect Power/Cable!

Thanks

Hello,
Install all drivers (download it from support site only)
Update your CM2 MTK ver (Current ver is 1.32)
Post result/logs....

Hm... 11 versions old SW support near 50% of current features. Please, check update logs. there is much things inside and explained.

Ok , sorry for delayed replay
All things updated , on next set will try and let you know
Thank you Support

Quote:

Originally Posted by JayDi (Post 11328104)

Hm... 11 versions old SW support near 50% of current features. Please, check update logs. there is much things inside and explained.

Ok hear i am Again , really :rolleyes: why i cant repair any MTK IMEI with Infinity.

Huawei U600 - Please dont say use 1.34. Thank You

Quote:

Card found : S/N : CB822A50 , v0129
Chinese Miracle II [MTK module] v 1.33

Operation : Check / Read Info [ v1.33 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 85 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 90014A4834473164040501A1BF3B71AD
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0090 , OEM : 014A
[eMMC] : FLASH_INF : d1G4
[eMMC] : FLASH_CID : 90014A4834473164040501A1BF3B71AD
[eMMC] : FLASH_EXT : 00400000/00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand : HUAWEI
ProdName : Y600-U20
ProdModel : HUAWEI Y600-U20
Device : HWY600-U
AndroidVer: 4.2.2
MTKxCPU : MT6572
MTKxPRJ : Y600-U20V100R001C435B012

MODEM :
BaseBand : MT6572_S00_MOLY_WR8_W1315_MD_WG_MP_V11_1_wg_n

EXTRA :
LCD [0] : otm8018b_dsi_vdo
LCD [1] : hx8379_fwvga_dsi_vdo
LCD Res : 854x480
TOUCH [0] : GT9XX
CAM [0] : ov5645_mipi_qiutai
CAM [1] : ov5645_mipi_yuv
CAM [2] : gc0329_yuv
MODEM : huaqin72_we_b2b_jb3_hspa_U00
LOCALE : en_US fa_IR ar_EG es_ES zh_CN zh_TW hdpi

Done!
Elapsed: 00:00:09
Reconnect Power/Cable!

Operation : Repair Security [ v1.33 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 85 ]
Sync...
Device boot not done
Check Drivers
Try again

Init Service mode failed, something went wrong :(

Reconnect Power/Cable!

Operation : Repair Security [ v1.33 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 85 ]
Sync...
Device boot not done
Check Drivers
Try again

Init Service mode failed, something went wrong :(

Reconnect Power/Cable!

On Read info Boot OK then on write security boot not done please check Drivers

Regards

OK Guys i made it , thanks any way. Just need to change Repair Mode in some Cases

Regards

Quote:

Card found : S/N : CB822A50 , v0129
Chinese Miracle II [MTK module] v 1.33

Operation : Repair Security [ v1.33 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 85 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 90014A4834473164040501A1BF3B71AD
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0090 , OEM : 014A
[eMMC] : FLASH_INF : d1G4
[eMMC] : FLASH_CID : 90014A4834473164040501A1BF3B71AD
[eMMC] : FLASH_EXT : 00400000/00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Set IMEI [00] : 864222027434666
Set IMEI [01] : 864222027535157
Prepare finished. Security check required!

Wait for phone...
Phone found! [ 85 ]
Sync...
PostCheck Ok! Repair done!

Done!
Elapsed: 00:00:38
Reconnect Power/Cable!

Yes , need select second Repair mode. In most cases.