repair badsoftware failed - GSM-Forum

hungsun_mobile · 11-05-2010, 07:07

hi all!

china e71-cpu 6225 repair fail

this is log

Quote:

COM8 [VCP0] selected
module v3.25
Action: repair "Bad software"
Step 1 of 2 is complete !
Press "Ok" now and then make step 2 !

If phone did not connect: remove/install battery.
Model: Autodetect 6205-6239 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6225:8A05:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:B303:000F
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6225,E05
Date: 2006.06.14
Version: 1.0
Version: SG2583_V0.05
Version: SINGLE25_GEMINI_HW
detecting structure #2...
1 2 3 5 7 8 9 11 13 done
80 byte(s) read
imei: 35524060613098
connection Ok
detecting structure #6 (mode-1)...
0 1 2 3 4 5 6 7error:
detection failed (8 tries)
What to do:
1. make full flash backup for emergency case
2. make "format ffs"
3. Power-On phone
4. Power-Off phone by "Power" button (do NOT remove battery)
5. Repeat operation again
6. if still no luck read full flash and send to support with subject: "bad software" repair failed
error: can't read required data
error: operation failed !
Finished, time used: 46 sec
Remove/Install battery now !

infi team please hepl me!

THANK!

InfinityHelp · 11-05-2010, 20:54

hello!

do you see "bad software" message on phone LCD?

hungsun_mobile · 11-06-2010, 02:33

yes,bad software displayed on LCD

Haider Ali · 11-06-2010, 10:57

Try full format the phone using (ffs)
Or
Full Flash your Phone

InfinityHelp · 11-07-2010, 11:41

hello!

please upload this firmware here, we must check it

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Nokia "Contact Service" Repairer	Dirk	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	5	10-04-2011 05:45
Contact Service Repairer 1.2 by Bartek	Allen	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	4	02-23-2011 09:00
New!! Nokia Flash Checksum And Contact Service Repair	HookerGsM	Main Sales Section	0	01-02-2001 10:12
Nokia 5110 v. 5.24 Unlock Failed!	Cybertooth	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	02-28-2000 15:35
Mti init failed	dogbreak	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	11-22-1999 01:28

11-05-2010, 20:54	#2 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! do you see "bad software" message on phone LCD?

11-06-2010, 02:33	#3 (permalink)
hungsun_mobile No Life Poster Join Date: Mar 2008 Location: Quang Tri- Viet Nam Posts: 562 Member: 723166 Status: Offline Sonork: 100.1590944 Thanks Meter: 129	yes,bad software displayed on LCD

11-06-2010, 10:57	#4 (permalink)
Haider Ali Freak Poster Join Date: Apr 2008 Location: Pakistan Age: 38 Posts: 379 Member: 756333 Status: Offline Thanks Meter: 152	Try full format the phone using (ffs) Or Full Flash your Phone

11-07-2010, 11:41	#5 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! please upload this firmware here, we must check it