Y620_u20 just vibrate after flash - GSM-Forum

daddyunl0cker1 · 11-11-2016, 23:10

Y620_u20 just vibrate after flash . Phone was have just pin lock .

i try with many versions but same but when i to make test its giving this error and please explain me about this error its mmc error or any other?

Quote:

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 6 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164040503A27481C177
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164040503A27481C177
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID : 0x0311512C6D10426C33C2CE0B409C0092
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Initial info read error! Erased or damaged FlashIC?!
Force eMMC test by user request

Processing Miscellaneous test
MSC : BatteryLevel : 3484 mV

[Processing] FlashMemory Read-Write test
[eMMC] : [HYNIX] , d1G4 , 0xE9000000 , 3728 MiB
[eMMC] : CID : 90014A4834473164040503A27481C177

[eMMC] : MODE : SQ-WR
[FAILED : READONLY] : eMMC state seems as READ-ONLY !!!!

Operation Failed
Elapsed: 00:01:02
Reconnect Power/Cable!

JayDi · 11-11-2016, 23:46

Hello. Because eMMC gone to ReadOnly due end of it resource - it not accept any FW and etc.

daddyunl0cker1 · 11-12-2016, 19:15

Quote:

Originally Posted by JayDi

Hello. Because eMMC gone to ReadOnly due end of it resource - it not accept any FW and etc.

can it alive boss ? ? ?

daddyunl0cker1 · 11-14-2016, 21:09

any solution to alive this ??

daddyunl0cker1 · 11-21-2016, 13:19

i have more 3 phones y520-u20 in same error can you help me ???

Kirumira · 11-21-2016, 13:38

Quote:

Originally Posted by daddyunl0cker1

i have more 3 phones y520-u20 in same error can you help me ???

Solution; Replace Emmc if you can.

Shensohau · 11-21-2016, 14:05

Hi, you don't need to replace emmc, if you flash wrong firmware on some mtk devices it will brick, for unbrick you need make testpoint, reflash with correct firmware and phone will be alive again... If EMMC is on good state by the way...

Best Regards
Shensohau

11-11-2016, 23:46	#2 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	Hello. Because eMMC gone to ReadOnly due end of it resource - it not accept any FW and etc.

11-14-2016, 21:09	#4 (permalink)
daddyunl0cker1 No Life Poster Join Date: Apr 2015 Posts: 568 Member: 2384553 Status: Offline Thanks Meter: 85	any solution to alive this ??

11-21-2016, 13:19	#5 (permalink)
daddyunl0cker1 No Life Poster Join Date: Apr 2015 Posts: 568 Member: 2384553 Status: Offline Thanks Meter: 85	i have more 3 phones y520-u20 in same error can you help me ???

11-21-2016, 14:05	#7 (permalink)
Shensohau No Life Poster Join Date: Aug 2010 Location: Inside Logic Age: 37 Posts: 5,882 Member: 1377783 Status: Offline Sonork: 100.1611724 Thanks Meter: 3,336	Hi, you don't need to replace emmc, if you flash wrong firmware on some mtk devices it will brick, for unbrick you need make testpoint, reflash with correct firmware and phone will be alive again... If EMMC is on good state by the way... Best Regards Shensohau