SM-j700F clone MT6572 HELP - GSM-Forum

recondition · 05-10-2017, 10:36

after try to flash SM-J700FN firmware with MT6572 also

now cannot flash back on his original backup from cm2

flashing error

Code:

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 298 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 11010030303447453001475C4ECE92CD
Initialize Memory ... 
DRAM configured from ScatFW!
DRAM initialize passed!
DRAM size : 0x20000000
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x11 , OEM : 0100
[eMMC] : FLASH_INF : [TOSHIBA] , 0EG40
[eMMC] : FLASH_CID : 11010030303447453001475C4ECE92CD
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000EC000000
[eMMC] : FLASH_UCP : 3776 MiB [eMMC 4 GiB]
DEV RID    : 0xD9B11B21E129F27C5103BC5CC44BCDF0
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6572 , Project : tangxun6572_we_l , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Enabled
Setting : HW verify :  Enabled

Switching to HSUSB
****ch to HSUSB failed! Trying skip ... 
BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : Unknown (not supported or without battery)

BL : Flash Pre-Erase
Total blocks to Erase : 3
Erase : 0x0000000000C00000-0x0000000000100000
Erase Error! Something went wrong!

Operation Failed
Elapsed: 00:00:16
Reconnect Power/Cable!

make test

Code:

Operation : HW Test [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 298 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 11010030303447453001475C4ECE92CD
Initialize Memory ... 
DRAM configured from ScatFW!
DRAM initialize passed!
DRAM size : 0x20000000
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x11 , OEM : 0100
[eMMC] : FLASH_INF : [TOSHIBA] , 0EG40
[eMMC] : FLASH_CID : 11010030303447453001475C4ECE92CD
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000EC000000
[eMMC] : FLASH_UCP : 3776 MiB [eMMC 4 GiB]
DEV RID    : 0xD9B11B21E129F27C5103BC5CC44BCDF0
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Processing Miscellaneous test
MSC : BatteryLevel : 3703 mV

[Processing] FlashMemory Read-Write test
[eMMC] : [TOSHIBA] , 0EG40 , 0xEC000000 , 3776 MiB
[eMMC] : CID : 11010030303447453001475C4ECE92CD

[eMMC] : MODE : SQ-WR
[PASSED] : eMMC RW Check #1 Ok!
[eMMC] : MODE : RA-WR
[PASSED] : eMMC RW Check #2 Ok!

[eMMC RO CHECK] : eMMC Ok! READ-WRITE Passed!

[Processing] RAM Read-Write test
[DRAM] : 0x20000000 , 512 MiB

[DRAM] : ADDRESS BUS test
[PASSED] : Bus Count : 0x1C
[DRAM] : DATA BUS test
[PASSED] : Bus Count : 0x1F
[DRAM] : PATTERN test
[PASSED] : PATTERN Ok
[DRAM] : INCDEC test
[PASSED] : INCDEC Ok

All Done!

Done!
Elapsed: 00:01:33
Reconnect Power/Cable!

any idea?

ilyasrao · 05-10-2017, 10:55

full formate using sp flash tool and then flash

recondition · 05-10-2017, 11:06

whole flash with sp flash tool

i dont know why after i flash on wrong firmware 2 times its still can flash then the last firmware i flash is SM-J700FN but still MT6572 after i flash that firmware then i want to revert back to the old backup of it then it cannot be flash...

recondition · 05-10-2017, 11:18

all done now..

battery lowbat only

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-10-2017, 10:55	#2 (permalink)
ilyasrao No Life Poster Join Date: Aug 2011 Posts: 576 Member: 1630066 Status: Offline Sonork: 520074 Thanks Meter: 215	full formate using sp flash tool and then flash

05-10-2017, 11:06	#3 (permalink)
recondition Insane Poster Join Date: May 2013 Posts: 81 Member: 1950121 Status: Offline Thanks Meter: 11	whole flash with sp flash tool i dont know why after i flash on wrong firmware 2 times its still can flash then the last firmware i flash is SM-J700FN but still MT6572 after i flash that firmware then i want to revert back to the old backup of it then it cannot be flash...

05-10-2017, 11:18	#4 (permalink)
recondition Insane Poster Join Date: May 2013 Posts: 81 Member: 1950121 Status: Offline Thanks Meter: 11	all done now.. battery lowbat only