Successfully unlocked/repaired phones by Infinity-Box

[sky73]

read firmware asus zenfone selfie z00ud

Operation : Read Flash [ v1.16 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ... 
Handshake passed!
ID_BLOCK_I : SnapDragon 610 [MSM8936]
ID_BLOCK_S : 015585B6
ID_BLOCK_E : 11112222
ID_BLOCK_L : 0F6D548069BC6EE02E06CAC33E46A502
ID_BLOCK_L : 6AB1F20E701A8D527565B38950769D50
Use CM2 Internal Loader
Loader Sent! Initializing ... 
Running FireHose on BBID : MSM8936 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x0000000747C00000 [ eMMC 32 GiB ] 
ExtInfo : 0x00004000/00004000/00001000/00001000/00000200
Boot Ok!


Brand     : asus
ProdName  : WW_Z00T
ProdModel : ASUS_Z00TD
Device    : Z00T
AndroidVer: 6.0.1
Manufact. : asus
QLMxCPU   : MSM8916

DevInfo : MSM8916__asus__asus__ANDR_v6.0.1__ASUS_Z00TD__Z00T__WW_Z00T

Reading Flash Content ... 
[Read Ok] : gpt_main0.bin
[Read Ok] : sbl1.mbn
[Read Ok] : rpm.mbn
[Read Ok] : tz.mbn
[Read Ok] : hyp.mbn
[Read Ok] : ddr.bin
[Read Ok] : sec.dat
[Read Ok] : emmc_appsboot.mbn
[Read Ok] : splash.img
[Read Ok] : fs_gc.img
[Read Ok] : misc.img
[Read Ok] : asdf.bin
[Read Ok] : abootdebug.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : persist.img
[Read Ok] : NON-HLOS.bin
[Read Ok] : adf.bin
[Read Ok] : apd.bin
[Read Ok] : cache.img
[Read Ok] : system.img
[Read Ok] : userdata.img
[Read Ok] : gpt_backup0.bin

Android Info saved!
Read finished!
Configuration : MSM8936 / eMMC
Firmware Size : 3349 MiB

Done!
Elapsed: 00:05:13

Reconnect Power/Cable!

[azhergoga007]

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

==== Wait for phone...

Phone found! [ 191 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size : 0x0000000117FF7000
State : 0x0001

Mount : /cache
Size : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x/6.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:21

Reconnect Power/Cable!

[moniuzzaman]

walton mm11 read code done by infinity box

Card found : S/N : 64C1CE3F , v0137
Chinese Miracle II [MTK module] v 1.58

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 9 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0000
BB_CPU_SN : 82FDDC19BFB6590CE0CB371D654EC599
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x0113 , [Winbond] SF_W25Q32JV
[0] : FLASH_DIE : 00EF 0070 0016 0000
[0] : FLASH_LEN : 0x00400000
SDS_INFO : 0x003FE000 , 0x00002000
INT_RAM : 0x0000D000
EXT_RAM : 0x00400000

Done!
Elapsed: 00:00:02
Reconnect Power/Cable!


Operation : Read UserCode [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 9 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0000
BB_CPU_SN : 82FDDC19BFB6590CE0CB371D654EC599
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x0113 , [Winbond] SF_W25Q32JV
[0] : FLASH_DIE : 00EF 0070 0016 0000
[0] : FLASH_LEN : 0x00400000
SDS_INFO : 0x003FE000 , 0x00002000
INT_RAM : 0x0000D000
EXT_RAM : 0x00400000

Read ExtData
Sorting ExtData
Reading UserCode

Active : Yes , Code : 74369

PLock|MobTrack : Not active

Done!
Elapsed: 00:00:03
Reconnect Power/Cable!

[VIJAY2U2]

Operation : Reset Settings [ v1.16 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ... 
Handshake passed!
ID_BLOCK_I : SnapDragon 425 [MSM8917]
ID_BLOCK_S : A11BBE24
ID_BLOCK_L : 3A67E4C26A79AFF283D56322B624D4FB
ID_BLOCK_L : E51369C80F2E38F6E178998CEB638FF2
Use CM2 Internal Loader
Loader Sent! Initializing ... 
Running FireHose on BBID : MSM8917 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x0000000747C00000 [ eMMC 32 GiB ] 
ExtInfo : 0x0001C000/00100000/00001000/00001000/00000200
Storage : MFR : 0x15 , VENDOR : SAMSUNG , NAME : GD6BMB
Boot Ok!

Remove FRP
Reset Ok!

Done!
Elapsed: 00:00:37

[VIJAY2U2]

Operation : Reset Settings [ v1.16 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ... 
Handshake passed!
ID_BLOCK_I : SnapDragon 410 [MSM8916]
ID_BLOCK_S : 19D7FE5D
ID_BLOCK_L : 6A9AF00EA935222D1A4F818E4910A0A8
ID_BLOCK_L : B2C14FDED342EC799C5B3CF5FF36202B
Use CM2 Internal Loader
Loader Sent! Initializing ... 
Running FireHose on BBID : MSM8916 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x00000001D2000000 [ eMMC 8 GiB ] 
ExtInfo : 0x00004000/00004000/00001000/00001000/00000200
Boot Ok!

Format USER ... 
Format CACHE ... 
Format Ok!
Remove FRP
Reset Ok!
Remove FRP
Reset Ok!

Done!
Elapsed: 00:00:21

Reconnect Power/Cable!

[VIJAY2U2]

Operation : Flash [ v1.16 ]
ForceFlashing : Disabled

Verify FW package ... 
Verification passed!

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ... 
Handshake passed!
ID_BLOCK_I : SnapDragon 425 [MSM8917]
ID_BLOCK_S : 5474245D
ID_BLOCK_L : F1BE2D09B3B26639582CBCEB7FEF2F20
ID_BLOCK_L : 3CB8B211A4F79F4F089330334CBA665B
Pickup loader from firmware package
Loader Sent! Initializing ... 
Running FireHose on BBID : MSM8917 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x00000003A3E00000 [ eMMC 16 GiB ] 
ExtInfo : 0x0001C000/00100000/00001000/00001000/00000200
Storage : MFR : 0x15 , VENDOR : SAMSUNG , NAME : QE63MB
Boot Ok!

Flash Chain : 51
Flashing now

Flashing : NON-HLOS.bin
Flashing : sbl1.mbn
Flashing : sbl1.mbn
Flashing : rpm.mbn
Flashing : rpm.mbn
Flashing : tz.mbn
Flashing : tz.mbn
Flashing : devcfg.mbn
Flashing : devcfg.mbn
Flashing : adspso.bin
Flashing : splash.img
Flashing : emmc_appsboot.mbn
Flashing : emmc_appsboot.mbn
Flashing : boot.img
Flashing : recovery.img
Flashing : system.img
Flashing : cache.img
Flashing : config.bin
Flashing : mdtp.img
Flashing : cmnlib.mbn
Flashing : cmnlib.mbn
Flashing : cmnlib64.mbn
Flashing : cmnlib64.mbn
Flashing : keymaster.mbn
Flashing : keymaster.mbn
Flashing : cust.img
Flashing : userdata.img
Flashing : gpt_main0.bin
Flashing : gpt_backup0.bin

Flash sequence completed!

Applying patches for storage # 0
Records : 26
Patch sequence completed!

BootConfig set to 0x00

Flashing done!

Done!
Elapsed: 00:02:54

[VIJAY2U2]

Chinese Miracle II  [MTK module] v 1.58

Start  at : [6/20/2018 / 5:26:17 PM]
Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6735
BB_CPU_NME : [MediaTek] MT6735_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 484A0190613447410068A4325B208110
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , 2a4GA
[eMMC] : FLASH_CID : 90014A484147346132A468001081925B
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003AB400000
[eMMC] : FLASH_UCP : 15028 MiB [eMMC 16 GiB]
DEV RID    : 0xFA6E6E938BA622A4546AD8EFB8F43E3D
INT RAM    : 0x00020000
EXT RAM    : 0x80000000 [2 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!

Done!
Elapsed: 00:00:12
Reconnect Power/Cable!

[VIJAY2U2]

Operation : Read Flash [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 5 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : 009800BC009000660076001600080000
eMMC Flash : NOT INSTALLED
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0011 , [KINGSTON] KTN0403CS_TCR1
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0016 0008
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
DEV RID    : 0xFA6E6E93048EDA5C6AF22AA6CAC8667D
INT RAM    : 0x00020000
EXT RAM    : 0x10000000 [256 MiB]
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Content now ... 

[Read Ok] : preloader_hexing72_cwet_lca.bin
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : usrdata.img

[ScatCFG] : MT6572 / V1.1.1 / hexing72_cwet_lca / NAND
FW Size : 256 MiB

Brand     : alps
ProdName  : Amaze S305
ProdModel : Amaze S305
Device    : hexing72_cwet_lca
AndroidVer: 4.4.2
MTKxCPU   : MT6572
MTKxPRJ   : Amaze_S305

Android Info saved

Scatter saved to : C:\Users\Vijay\Downloads\MT6572_NAND_alps__Amaze S305__hexing72_cwet_lca__4.4.2__Amaze_S305

Done!
Elapsed: 00:02:26
Reconnect Power/Cable!

[Luckey1]

Core : v2.29 , BB5XG FlashEngine : v10.5

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm837__03.51.mcusw
PPM : rm837__03.51.ppm_m2
CNT : rm837__03.51.image_m2_059P7C1
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...

-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---

Connection opened successfully

IF Boot Init : 0xF0
IF Resp Len : 0x0A
IF xCPUID : XGOLD 213 [XMM2130 QUANTUM]
IF Resp Data : 1FB300020303010100FF

Sending EBL Loader ...
EBL Loader Ok, 01
EBL Loader ready, AA
Sending EBL ...
EBL sent Ok
EBL : Quantum_Bootloader_10.50_M1S1
Speed accepted, use 6.500.000
FLASHID : EC001230
FLIC conf set, RST set
Boot done!

Check keys...
Check done. Image can be flashed

Backup enabled, will read all certificates

Reading CCC
Reading HWC
Reading NPC

IMEI 1 : 355485054206085
IMEI 2 : 355485054206093
PCcode : 059P7C1

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : C:\InfinityBox\BEST\Backup\Cert\355485054206085_XG 213_CRT.rpl

Settings : EDM [0x8] , Block Mode , Fast CRC , Verify

===Flashing [MCU]===
File : rm837__03.51.mcusw
Image : rm837__03.51.mcusw_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:00
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait ...
Erase done, time : 00:00:02
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait ...
Region flash done, time : 00:00:01
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01940000
Erasing, wait ...
Erase done, time : 00:00:51
Write , Start : 0x40280000 , Len : 0x018C0000
Flashing , wait ...
Region flash done, time : 00:00:35
Processing Region 5/5
Erase , Start : 0x43E20000 , Len : 0x00040000
Erasing, wait ...
Erase done, time : 00:00:00
No write data, skip
CRC check passed , 0x87F4

===Flashing [PPM]===
File : rm837__03.51.ppm_m2
Image : package_m2.ppm_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x41BC0000 , Len : 0x00600000
Erasing, wait ...
Erase done, time : 00:00:06
Write , Start : 0x41BC0000 , Len : 0x0030F7C0
Flashing , wait ...
Region flash done, time : 00:00:03
CRC check passed , 0x46E6

===Flashing [CNT]===
File : rm837__03.51.image_m2_059P7C1
Image : package_m2_059P7C1.image.fls
Sec-pack found, sending ...
Sec-pack sent
Found 2 region(s)
Processing Region 1/2
Erase , Start : 0x421C0000 , Len : 0x01C60000
Erasing, wait ...
Erase done, time : 00:01:23
Write , Start : 0x421C0000 , Len : 0x00EE0000
Flashing , wait ...
Region flash done, time : 00:00:20
Processing Region 2/2
Erase , Start : 0x43E60000 , Len : 0x000E0000
Erasing, wait ...
Erase done, time : 00:00:01
No write data, skip
CRC check passed , 0x2559

Flashing done!
Total flash time : 00:03:27
Reboot phone now...

Reading Phone Info....
Connected phone - Nokia 112
Software Info: V 03.51 06-08-13 RM-837 (c) Nokia
IMEI: 355485054206085
PPM version : V 03.51 06-08-13 RM-837 (c) Nokia M2
Product code: 059P7C1
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Processing After Flash Defaults...
FullFactorySet... Ok!
UserDataDefaultsSet...OK!
ServiceDefaultsSet... Ok!
LeaveDefaultsSet... Ok!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Check and Upload User Certificates ...
Total - 58 certs
Certificates found, skip upload ...
AfterFlash operations done ;D
Done!
Connect phone on selected interface...


Elapsed: 00:04:29

[gile@gile]

Alcatel 5022D Read Pattern done

Card found : S/N : 07EDXXXX , v0136
Chinese Miracle II [MTK module] v 1.58

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 7 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v3.3001.00.00
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x9C
NAND Flash : NOT INSTALLED
eMMC Flash : 150100513732534D420001BE6AE23307
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMS27
[eMMC] : FLASH_CID : 150100513732534D420001BE6AE23307
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0x7FBB5333425FD65CD43A13E16293E6BC
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand : TCL
ProdName : 5022D
ProdModel : 5022D
Device : PLAY-5
AndroidVer: 5.1
MTKxCPU : MT6580
MTKxPRJ : ALPS.L1.MP6.V2_AUS6580.WE.L_P81

Done!
Elapsed: 00:00:20
Reconnect Power/Cable!


Operation : Read Pattern/DP Lock [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 7 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v3.3001.00.00
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x9C
NAND Flash : NOT INSTALLED
eMMC Flash : 150100513732534D420001BE6AE23307
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMS27
[eMMC] : FLASH_CID : 150100513732534D420001BE6AE23307
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0x7FBB5333425FD65CD43A13E16293E6BC
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading data ...

Get Locks ...
PatternLock Sequnce : 635241789

Done!
Elapsed: 00:00:24
Reconnect Power/Cable!

[sky73]

ASUS ZENFONE LIVE ZB501KL (ASUS A007) enable adb and reset frp

Operation : Reset FRP [ v1.03 ]
Mode : Remove ASUS GENERIC FRP
 
Waiting for device in fastboot mode ... 
 
1. Power off device. Press and hold 'VOL DOWN' button
2. Insert USB cable, hold button until device will be found!
 
Connect Ok!
 
ADB activated!
- > Info : Wait till device boot, make offline setup until device show message about protection
- > Info : Re-connect cable, make "FRP Reset" in ADB tab!

Done!
Elapsed: 00:00:07

Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ... 
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Device not found! Check cable, drivers and conection!
 
Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ... 
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 

Error : Fail to init secure handshake!
Check cable, connection, drivers and AUTH dialog on device screen!


Operation : Reset FRP (ADB) [ v1.03 ]
 
Waiting for device in ADB mode ... 
 
1. Connect device, enable 'DEVELOPER MODE' and 'USB DEBUG', if need!
2. Insert USB cable, accept AUTH on PhoneScreen, if software ask!
 
Connect Ok!
 
Device : WW_Phone
Model  : ASUS_A007
FRP reset passed! Make FACTORY RESET from menu!
 

Done!
Elapsed: 00:00:07

[Kirumira]

BLU STUDIO 5.0 LTE READ FIRMWARE & RESET USERLOCK DONES

Operation : Identify [ v1.16 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ... 
Handshake passed!
ID_BLOCK_I : SnapDragon 410 [MSM8916]
ID_BLOCK_S : 08FE6DDF
ID_BLOCK_L : E41C76802FBBA0A39CF1030CCB961E2E
ID_BLOCK_L : D5A816B9BA25951EB302578C86690744
Use CM2 Internal Loader
Loader Sent! Initializing ... 
Running FireHose on BBID : MSM8916 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x00000001D2000000 [ eMMC 8 GiB ] 
ExtInfo : 0x00004000/00004000/00001000/00001000/00000200
Boot Ok!


Brand     : BLU
ProdName  : STUDIO5.0LTE
ProdModel : BLU STUDIO 5.0 LTE
Device    : msm8916_32
AndroidVer: 4.4.4
Manufact. : BLU
SysPatch  : KTU84P
DevComTime: 18/06/2015 10:57:31
QLMxCPU   : MSM8916
QLMxPRJ   : BLU_Z030Q_V09_GENERIC_20150618-1857

USERData : NORMAL
GCSec    : NORMAL

Done!
Elapsed: 00:00:23

Reconnect Power/Cable!

Operation : Read Flash [ v1.16 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ... 
Handshake passed!
ID_BLOCK_I : SnapDragon 410 [MSM8916]
ID_BLOCK_S : 08FE6DDF
ID_BLOCK_L : E41C76802FBBA0A39CF1030CCB961E2E
ID_BLOCK_L : D5A816B9BA25951EB302578C86690744
Use CM2 Internal Loader
Loader Sent! Initializing ... 
Running FireHose on BBID : MSM8916 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x00000001D2000000 [ eMMC 8 GiB ] 
ExtInfo : 0x00004000/00004000/00001000/00001000/00000200
Boot Ok!


Brand     : BLU
ProdName  : STUDIO5.0LTE
ProdModel : BLU STUDIO 5.0 LTE
Device    : msm8916_32
AndroidVer: 4.4.4
Manufact. : BLU
QLMxCPU   : MSM8916
QLMxPRJ   : BLU_Z030Q_V09_GENERIC_20150618-1857

DevInfo : MSM8916__BLU__BLU__ANDR_v4.4.4__BLU_STUDIO_5.0_LTE__msm8916_32__STUDIO5.0LTE__BLU_Z030Q_V09_GENERIC_20150618-1857

Reading Flash Content ... 
[Read Ok] : gpt_main0.bin
[Read Ok] : NON-HLOS.bin
[Read Ok] : sbl1.mbn
[Read Ok] : emmc_appsboot.mbn
[Read Ok] : rpm.mbn
[Read Ok] : tz.mbn
[Read Ok] : hyp.mbn
[Read Ok] : misc.img
[Read Ok] : splash.img
[Read Ok] : fs_gc.img
[Read Ok] : sec.dat
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : persist.img
[Read Ok] : cache.img
[Read Ok] : recovery.img
[Read Ok] : userdata.img
[Read Ok] : gpt_backup0.bin
[Read Ok] : gpt_main2.bin
[Read Ok] : cdt.mbn
[Read Ok] : gpt_backup2.bin

Android Info saved!
Read finished!
Configuration : MSM8916 / eMMC
Firmware Size : 1091 MiB

Done!
Elapsed: 00:03:12

Operation : Reset UserLocks [ v1.16 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ... 
Handshake passed!
ID_BLOCK_I : SnapDragon 410 [MSM8916]
ID_BLOCK_S : 08FE6DDF
ID_BLOCK_L : E41C76802FBBA0A39CF1030CCB961E2E
ID_BLOCK_L : D5A816B9BA25951EB302578C86690744
Use CM2 Internal Loader
Loader Sent! Initializing ... 
Running FireHose on BBID : MSM8916 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x00000001D2000000 [ eMMC 8 GiB ] 
ExtInfo : 0x00004000/00004000/00001000/00001000/00000200
Boot Ok!

Direct access : Ok!
Processing step #1
Processing step #2
Processing step #3
Processing step #4
Processing step #5
Processing step #6
Processing step #7

UserLocks reset passed!
1. Power On phone, wait 30-50 second, press and hold PowerOn button until device restart!
2. To disable/remove fingerprints enter in Settings -> FingerPrint, set any password, remove fingerprints
3. In some cases require reboot phone twice or wait up to 5 minutes!

Done!
Elapsed: 00:00:56

[Kirumira]

Lenovo K50-T5 DL IMAGE FAILED & UPGRADE TO ADROID 6.0 DONE

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 14 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6752
BB_CPU_NME : [MediaTek] MT6732|MT6752_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8F
NAND Flash : NOT INSTALLED
eMMC Flash : 150100523832314D42007E1BC2CEA22F
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM128
[eMMC] : FLASH_CID : 150100523832314D42007E1BC2CEA22F
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID    : 0x0E03E514EC136C91BE71CAC5BC2BD126
INT RAM    : 0x00020000
EXT RAM    : 0x80000000 [2 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : Lenovo
ProdName  : full_aio_otfp
ProdModel : Lenovo K50-T5
Device    : aio_otfp
AndroidVer: 5.0
MTKxCPU   : MT6752
MTKxPRJ   : K50-T5_USR_ST1511_5.444.1_1503111505_MP6V3_CN

SECURITY : 
IMEI_SW [1] : 3XXXXXXXXXXX
IMEI_SW [2] : 35XXXXXXXXXXXX
BTMAC Addr  : A03299FD3C68
WiFi MAC    : 5427580F3C68

MODEM : 
BaseBand  : MT6752_S00_K50T5_LTG_V21_1_ltg_n

EXTRA : 
LCD [0] : nt35595_fhd_dsi_cmd_truly_nt50358
LCD Res : 1920x1080
TOUCH [0] : GT9XX_hotknot
CAM [0] : ov13850sunny_mipi_raw
CAM [1] : ov13850ofilm_mipi_raw
CAM [2] : ov5670_mipi_raw
MODEM : aio_5m_ltg_dsds aio_5m_lwg_dsds
LOCALE : en_US zh_CN zh_TW es_ES pt_BR ru_RU fr_FR de_DE tr_TR vi_VN ms_MY in_ID th_TH it_IT ar_EG hi_IN bn_IN ur_PK fa_IR pt_PT nl_NL el_GR hu_HU tl_PH ro_RO cs_CZ ko_KR km_KH iw_IL my_MM pl_PL es_US bg_BG hr_HR lv_LV lt_LT sk_SK uk_UA de_AT da_DK fi_FI nb_NO sv_SE en_GB hy_AM zh_HK et_EE ja_JP kk_KZ sr_RS sl_SI ca_ES

Done!
Elapsed: 00:00:17
Reconnect Power/Cable!

Operation : Fix DL Errors [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 14 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6752
BB_CPU_NME : [MediaTek] MT6732|MT6752_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8F
NAND Flash : NOT INSTALLED
eMMC Flash : 150100523832314D42007E1BC2CEA22F
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM128
[eMMC] : FLASH_CID : 150100523832314D42007E1BC2CEA22F
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID    : 0x0E03E514EC136C91BE71CAC5BC2BD126
INT RAM    : 0x00020000
EXT RAM    : 0x80000000 [2 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

DA DLFix Passed!

Done!
Elapsed: 00:00:11
Reconnect Power/Cable!

Scatter Load Ok , BaseBand : MT6752 , Project : aio_5m , Storage : EMMC
Files found : 11 , Set to Flash : 10
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand   : Lenovo
Device Model   : K50-t5
Device CPU     : MT6752
Device IntName : aio_otfp
Device Version : 6.0
Device Compile : 15/03/2016 01:06:25
Device Project : K50-t5_USR_S422_1603150849_mp1V2.39_ROW
Device ExtInfo : Lenovo K50-t5
Ready to Flash!

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 14 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6752
BB_CPU_NME : [MediaTek] MT6732|MT6752_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8F
NAND Flash : NOT INSTALLED
eMMC Flash : 150100523832314D42007E1BC2CEA22F
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM128
[eMMC] : FLASH_CID : 150100523832314D42007E1BC2CEA22F
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID    : 0x0E03E514EC136C91BE71CAC5BC2BD126
INT RAM    : 0x00020000
EXT RAM    : 0x80000000 [2 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6752 , Project : aio_5m , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Enabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 4059 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000001C80000-0x0000000006320000
Erase : 0x0000000008800000-0x000000039A580000
Flash Pre-Erase Done, time used : 00:00:08

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ... 
Use : preloader_aio_5m.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0013
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : TEE1
Image Flash Ok
Flash now : TEE2
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:08:39

Processing : Verify
Verify Passed : LK
Verify Passed : BOOT
Verify Passed : RECOVERY
Verify Passed : SECRO
Verify Passed : LOGO
Verify Passed : TEE1
Verify Passed : TEE2
Verify Passed : SYSTEM
Verify Passed : CACHE
Verify Passed : USERDATA
Data Verify Done, time used : 00:00:10

Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:09:31
Reconnect Power/Cable!

[VIJAY2U2]

Operation : Flash [ v1.27 ]

======= Flash
Files set for flashing : 
[ MCU ] : INTEX_ELYT_DUAL_V09_INDIAN_1205_1801_user_lockV06.pac
CRVersion  : BP_R1.0.0
PacCPUinfo : sp9850ka_2c20
PacVersion : INTEX_ELYT_DUAL_V09_INDIAN_1205_1801_user_lockV06
File : fdl1-sign.bin
File : fdl2-sign.bin
File : ltenvitem.bin
File : prodnv.img
File : u-boot-spl-16k-sign.bin
File : ltemodem.bin
File : ltedsp.bin
File : ltegdsp.bin
File : pmsys.bin
File : wcnmodem.bin
File : boot.img
File : recovery.img
File : sysinfo.img
File : system.img
File : userdata.img
File : logo.bmp
File : logo.bmp
File : cache.img
File : tos-sign.bin
File : sml-sign.bin
File : u-boot-sign.bin
File : persist.img

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 
3. Insert cable

 ====  Wait for phone...

Phone found! [ 4 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
PMTManager : Load 0x1D records
PMTManager : PMT Update Ok!
Flashing now

[FlashProc] : CODE  
Current ID : PRODNV
Current File : prodnv.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : ERASEUBOOT
Current Part : uboot
[FlashProc] : Ok!

[FlashProc] : BOOTCODE
Current ID   : SPLLOADER
Current File : u-boot-spl-16k-sign.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : MODEM_LTE
Current File : ltemodem.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : DSP_LTE_LTE
Current File : ltedsp.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : DSP_LTE_GGE
Current File : ltegdsp.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : DFS
Current File : pmsys.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : MODEM_WCN
Current File : wcnmodem.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : BOOT
Current File : boot.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : RECOVERY
Current File : recovery.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : SYSINFO
Current File : sysinfo.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : SYSTEM
Current File : system.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : USERDATA
Current File : userdata.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : BOOTLOGO
Current File : logo.bmp
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : FASTBOOT_LOGO
Current File : logo.bmp
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : CACHE
Current File : cache.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : FLASH_LTE
Current Part : l_runtimenv1
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : ERASEMISC
Current Part : misc
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : TRUSTOS
Current File : tos-sign.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : SML
Current File : sml-sign.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : BOOTCODE
Current ID   : UBOOTLOADER
Current File : u-boot-sign.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : PERSIST
Current File : persist.img
Flashing now ... 
[FlashProc] : Ok!


Elapsed: 00:05:05

Reconnect Power/Cable!

[VIJAY2U2]

Set mode to : SPD6530_SAMSUNG

Start  at : [6/20/2018 / 8:52:11 PM]
Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 33 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ... 
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2    Boot Ok
CPU ID : 6530 , FDLStat : 00C0
[0] Flash DIE : 00C8 0060 0017 0000
[0] Flash VEN : GigaDevice , GD25LQ64
[0] Flash CAP : 00800000
Verify data... Can take some time
Init Ok, formatting DIN area ... 
Format Block Done!
Done!

Elapsed: 00:00:25

Reconnect Power/Cable!