Successfully unlocked/repaired phones by Infinity-Box - Page 4136 - GSM-Forum

Luckey1 · 01-15-2020, 07:32

Rivo s625 read user code done

Operation : Read UserCode [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 28 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0000
BB_CPU_SN : 1FCEA5DAB7046724B15CC07534A52415
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
InitRes : 00000000
DEV[0] : C800 6000 1800 0000
DEV[1] : 0000 0000 0000 0000
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00F4 , [GigaDevice] GD25LQ128
[0] : FLASH_DIE : 00C8 0060 0018 0000
[0] : FLASH_LEN : 0x01000000
INT_RAM : 0x0000D000
EXT_RAM : 0x00800000

Read ExtData
Sorting ExtData
Reading UserCode

Active : Yes , Code : 5588

Privacy Lock :6

Done!
Elapsed: 00:00:34
Reconnect Power/Cable!

Tanha0321 · 01-15-2020, 10:29

Code:

Brand     : TINNO
ProdName  : QMobile X30
ProdModel : QMobile X30
Device    : QMobile X30
AndroidVer: 4.4.2
MTKxCPU   : MT6572
MTKxPRJ   : ALPS.KK1.MP7.V1

Done!
Elapsed: 00:00:09
Reconnect Power/Cable!


Scatter Load Ok , BaseBand : MT6572 , Project : s4050ap , Storage : EMMC
Files found : 11 , Set to Flash : 10
Ready to Flash!

Operation : Flash [ v1.58 ]


======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A48344732611101C19B8A5C6235
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , a2G4
[eMMC] : FLASH_CID : 90014A48344732611101C19B8A5C6235
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID    : 0xD5229C2529493CF118F22B7ADA5BB6AA
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6572 , Project : s4050ap , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Disabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 3724 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000000C00000-0x0000000000100000
Erase : 0x0000000002900000-0x00000000E5E00000
Flash Pre-Erase Done, time used : 00:00:00

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ... 
Use : preloader_s4050ap.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0012
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : MBR
Image Flash Ok
Flash now : EBR1
Image Flash Ok
Flash now : UBOOT
Image Flash Ok
Flash now : BOOTIMG
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SEC_RO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : ANDROID
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USRDATA
Image Flash Ok
Flash Write Done, time used : 00:02:50


Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:03:14
Reconnect Power/Cable!

Tanha0321 · 01-15-2020, 10:30

Code:

Brand     : Nokia
ProdName  : Frontier_00WW
ProdModel : Nokia 1
Device    : FRT
AndroidVer: 8.1.0

Done!
Elapsed: 00:00:09
Reconnect Power/Cable!


Operation : Format FileSystem [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 7 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6737
BB_CPU_NME : [MediaTek] MT6737M|MT6737_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x01000000
BromVer   : 0x00FF
BLVersion : 0x0002
PreLoader : Active [ Boot with PL ]
BootLdrSS : SIGNED with SPRELOADER
Processing DA stage
DA Select done, will use SecMode DA
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x9B
NAND Flash : NOT INSTALLED
eMMC Flash : 484A0190613447383537A5326189253E
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , 2a4G8
[eMMC] : FLASH_CID : 90014A483847346132A537353E253561
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0xD5229C25640204222A84C22FFE4F8064
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!

Done!
Elapsed: 00:00:13
Reconnect Power/Cable!

Tanha0321 · 01-15-2020, 10:31

Code:

Brand     : OPPO
ProdName  : A37f
ProdModel : A37f
Device    : A37f
AndroidVer: 5.1.1
SWVersion : A37fEX_11.A.28_INT_028_201710081545
Manufact. : OPPO
SysPatch  : LMY47V
DevComTime: 10/8/2017 9:26:49 AM
QLMxCPU   : MSM8916

USERData : NORMAL
GCSec    : EMPTY

Done!
Elapsed: 00:00:18

Reconnect Power/Cable!

Operation : Read PatternLock [ v1.16 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ... 
Handshake passed!
ID_BLOCK_I : SnapDragon 410 [MSM8916]
ID_BLOCK_S : 26D3FDBE
ID_BLOCK_L : CB3D57AF0E94818C7BD0202DEAB1C109
ID_BLOCK_L : 8EC54BE2D77EE065985738F1F3322C2F
Use CM2 Internal Loader
Loader Sent! Initializing ... 
Running FireHose on BBID : MSM8916 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x00000003AB400000 [ eMMC 16 GiB ] 
ExtInfo : 0x00004000/00004000/00001000/00001000/00000200
Boot Ok!

Read Ok! Trying decrypt ... 
PatternLock sequence : 4589

Done!
Elapsed: 00:00:26

Reconnect Power/Cable!

Tanha0321 · 01-15-2020, 10:31

Code:

Brand     : QMobile
ProdName  : QMobile i6i
ProdModel : QMobile i6i
Device    : QMobile
AndroidVer: 5.1
MTKxCPU   : MT6580
MTKxPRJ   : ALPS.L1.MP6.V2_TINNO6580.WE.L

Done!
Elapsed: 00:00:28
Reconnect Power/Cable!


Scatter Load Ok , BaseBand : MT6580 , Project : s5030 , Storage : EMMC
Files found : 9 , Set to Flash : 8
Ready to Flash!

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 4 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 150100464A32374D42026D9DCCE7A25F
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM72J
[eMMC] : FLASH_CID : 150100464A32374D42026D9DCCE7A25F
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID    : 0xD5229C25D94926AB344A8129437296FE
INT RAM    : 0x00020000
EXT RAM    : 0x30000000 [768 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6580 , Project : s5030 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Disabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Skip checking by User request!

BL : BatteryLevel : 3186 mV
BL : [WARNING] : BatteryLevel LOW!!!

BL : Flash Pre-Erase
Total blocks to Erase : 1
Erase : 0x0000000001C80000-0x00000000E6300000
Flash Pre-Erase Done, time used : 00:00:02

SecCfg Passed , 1799
BMT remark not need. Will skip

Preloader Download skipped by user request! 
PartCount : 0014
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:03:02


Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:03:21
Reconnect Power/Cable!

Tanha0321 · 01-15-2020, 10:32

Code:

Patch Level    : NRD90M
Display ID     : QMobile_i8i PRO_MP_31_01
Ver. Incmt     : 62
Ver. CodeName  : REL
Ver. Release   : 7.0
Sec. Patch     : 2017-12-05
Build Time     : 1518318739
Product Model  : QMobile i8i PRO
Product Brand  : Qmobile
Product Name   : i8i_PRO
Product Device : i8i_PRO
Product Board  : sp7731cea
Product Manfct : Qmobile
Board Platform : sc8830
Product Info   : i8i_PRO

Update DataBase ... 


Platform Version: MOCORTM_W17.14.5_Debug
Project Version:   sc7731C_CP0_modem
BASE  Version:    TM_BASE_W17.14.5
MMI Version:       sc7731C_modem
HW Version:        sc7731C_CP0_modem
CMP_Time : 04-07-2017 14:07:41

MODEM TAG : MOCORTM_W17.14.5_Debug_TM_BASE_W17.14.5_sc7731C_CP0_modem_sc7731C_CP0_modem_sc7731C_modem

UserData : STATE : PLAIN


Done!
Elapsed: 00:01:29

Operation : Format FS / Reset Settings [ v2.04 ]
Mode : Reset FRP
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ... 

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731x_BASE : SC7731C_eMMC_1GB_NS
Sending Init Boot ... 
Boot sent!
Kick FDL ... 
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ... 
Port speed : 921600
Sending Flash Boot ... 
Boot sent!
Kick FLASH FDL ... 
ProtoEx :  : TRCC not supported!
FDL : Control transfered!

Boot Done!

Wipe Ok : FRP

Reconnect Power/Cable!


Done!
Elapsed: 00:01:06

Tanha0321 · 01-15-2020, 10:33

Code:

Operation : Format FileSystem [ v1.05 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ... 

Device Connected!
BootVersion : SPRD3
BootSource  :  InternalLibrary
BootVersion : Infinity SCR SC6531E Loader v 1.2
Port speed : 921600
FDL Flash  : Control transfered!

Boot Done!

CS0_MEM : SPI : [WINBOND] : W25Q32 : 0x00400000 [ 4MiB ]

Make backup of sensetive data
Backup saved to : C:\InfinityBox\CM2SCR\Backup\00400000_FMT_BACK_0E6641347378_NVM.nv

Executing FormatFFS ... 
Format FFS Done!

Done!
Elapsed: 00:00:24

Reconnect Power/Cable!

Tanha0321 · 01-15-2020, 10:33

Code:

Brand     : QTab
ProdName  : QTab_V3
ProdModel : QTab V3
Device    : QTab
AndroidVer: 4.4.2
MTKxCPU   : MT6572
MTKxPRJ   : ALPS.KK1.MP7.V1.43

Done!
Elapsed: 00:00:05
Reconnect Power/Cable!


Scatter Load Ok , BaseBand : MT6572 , Project : qmobile12c_9120 , Storage : EMMC
Files found : 11 , Set to Flash : 10
Ready to Flash!

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 3 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 8801034E436172642042A1543156A231
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x88 , OEM : 0103
[eMMC] : FLASH_INF : [FORESEE] , draC
[eMMC] : FLASH_CID : 8801034E436172642042A1543156A231
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000001CE100000
[eMMC] : FLASH_UCP : 7393 MiB [eMMC 8 GiB]
DEV RID    : 0xD5229C2542CF1464A83D667250F5ED64
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6572 , Project : qmobile12c_9120 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Disabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Skip checking by User request!

BL : BatteryLevel : 3525 mV
BL : [WARNING] : BatteryLevel LOW!!!

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000001000000-0x0000000000100000
Erase : 0x0000000002D00000-0x00000001CA320000
Flash Pre-Erase Done, time used : 00:00:02

SecCfg Passed , 1799
BMT remark not need. Will skip

Preloader Download skipped by user request! 
PartCount : 0012
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : MBR
Image Flash Ok
Flash now : EBR1
Image Flash Ok
Flash now : UBOOT
Image Flash Ok
Flash now : BOOTIMG
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SEC_RO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : ANDROID
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USRDATA
Image Flash Ok
Flash Write Done, time used : 00:02:39


Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:02:58
Reconnect Power/Cable!

Tanha0321 · 01-15-2020, 10:34

Code:

Operation : Format FileSystem [ v1.05 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ... 

Device Connected!
BootVersion : SPRD3
BootSource  :  InternalLibrary
BootVersion : Infinity SCR SC6531E Loader v 1.2
Port speed : 921600
FDL Flash  : Control transfered!

Boot Done!

CS0_MEM : SPI : [WINBOND] : W25Q32 : 0x00400000 [ 4MiB ]

Make backup of sensetive data
Backup saved to : C:\InfinityBox\CM2SCR\Backup\00400000_FMT_BACK_188FEB0105C8_NVM.nv

Executing FormatFFS ... 
Format FFS Done!

Done!
Elapsed: 00:00:23

Reconnect Power/Cable!

azhergoga007 · 01-15-2020, 11:24

Operation : Reset Settings [ v1.16 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ...
Handshake passed!
ID_BLOCK_I : SnapDragon 625 [MSM8953]
ID_BLOCK_S : 52AA2EB6
ID_BLOCK_L : A81172501CEBDD80314B1550C4B64689
ID_BLOCK_L : 7282F85F9EB9A9817EC90AFD7AEC386D
Use CM2 Internal Loader
Loader Sent! Initializing ...
Running FireHose on BBID : MSM8953 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x0000000747C00000 [ eMMC 32 GiB ]
ExtInfo : 0x0001C000/00100000/00001000/00001000/00000200
Storage : MFR : 0x45 , VENDOR : SANDISK , NAME : DL2032
Boot Ok!

MIAccount reset passed!

Device may relock back on WiFi/Network enable!

Done!
Elapsed: 00:00:22

Reconnect Power/Cable!

kothamamun · 01-15-2020, 14:09

Code:

Card found : CA7920A6 , v0139
Infinity-Box Chinese Miracle II : SPD/USC Module [SP2] v2.04

Load IDBase v1119 Ok!


Operation : Format FS / Reset Settings [ v2.04 ]
Mode : Reset FRP
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ... 

Device Connected!
BootVersion : SPRD3
Boot : INF : Symphony : i68
Sending Init Boot ... 
Boot sent!
Kick FDL ... 
ERROR : FDL NOT started!

Error : Fail to boot FDL!
Unsupported device with selected fdl! Change settings!

Reconnect Power/Cable!

Operation : Format FS / Reset Settings [ v2.04 ]
Mode : Reset FRP
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ... 

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731E_BASE : SC7731E_eMMC_1GB_RS
Sending Init Boot ... 
Boot sent!
Kick FDL ... 
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ... 
Port speed : 921600
Sending Flash Boot ... 
Boot sent!
Kick FLASH FDL ... 
FDL : Control transfered!

Boot Done!

Wipe Ok : FRP

Reconnect Power/Cable!


Done!
Elapsed: 00:00:37

kothamamun · 01-15-2020, 14:48

Code:

Operation : Identify [ v2.04 ]
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ... 

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731E_BASE : SC7731E_eMMC_1GB_RS
Sending Init Boot ... 
Boot sent!
Kick FDL ... 
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ... 
Port speed : 921600
Sending Flash Boot ... 
Boot sent!
Kick FLASH FDL ... 
FDL : Control transfered!

Boot Done!

Device info : 
Patch Level    : OPM2.171019.012
Display ID     : OPM2.171019.012 release-keys
Ver. Incmt     : 1536803841
Ver. CodeName  : REL
Ver. Release   : 8.1.0
Sec. Patch     : 2018-08-05
Build Time     : 1536804131
Product Info   : k121
Product Model  : V98
Product Brand  : Symphony
Product Name   : V98
Product Device : V98
Product Manfct : Symphony
Product Board  : k121
Board Platform : sp7731e

Update DataBase ... 


Platform Version: MOCORTM_17C_W18.23.4_P2_Debug
Project Version:   pike2_pub
BASE  Version:    FM_BASE_17C_W18.23.4_P2
HW Version:        sc7731e_modem

MODEM TAG : MOCORTM_17C_W18.23.4_P2_Debug_FM_BASE_17C_W18.23.4_P2_sc7731e_modem_pike2_pub

UserData : STATE : PLAIN


Done!
Elapsed: 00:01:48

Code:

Operation : Read FW [ v2.04 ]

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ... 

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731E_BASE : SC7731E_eMMC_1GB_RS
Sending Init Boot ... 
Boot sent!
Kick FDL ... 
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ... 
Port speed : 921600
Sending Flash Boot ... 
Boot sent!
Kick FLASH FDL ... 
FDL : Control transfered!

Boot Done!

Device info : 
Patch Level    : OPM2.171019.012
Display ID     : OPM2.171019.012 release-keys
Ver. Incmt     : 1536803841
Ver. CodeName  : REL
Ver. Release   : 8.1.0
Sec. Patch     : 2018-08-05
Build Time     : 1536804131
Product Info   : k121
Product Model  : V98
Product Brand  : Symphony
Product Name   : V98
Product Device : V98
Product Manfct : Symphony
Product Board  : k121
Board Platform : sp7731e

AndroidVer : 8
VlnrLevel : 0x00

SP7731E__Symphony__V98__8.1.0__OPM2.171019.012__k121

Read : prodnv.img
ExtSparse : Compression ratio : 19%
Read : phase.cfg
Read : recovery.img
Read : tos.bin
Read : sml.bin
Read : u-boot.bin
Read : boot_logo.bmp
Read : fastboot_logo.bmp
Read : nvitem_w.bin
Make : persist.img
Read : gnssmodem.bin
Read : gnssbdmodem.bin
Read : modem_wcn.img
Read : modem_w.bin
Read : deltanv_w.bin
Read : gdsp_w.bin
Read : pm_sys.bin
Read : boot.img
Read : system.img
ExtSparse : Compression ratio : 70%
Make : cache.img
Read : vendor.img
ExtSparse : Compression ratio : 49%
Read : vbmeta.img
Make : userdata.img
Read : u-boot-spl.bin

Firmware size : 0x4D9961A4 ( 1.21 GiB )
Android Info saved : _Android_info.txt
Reconnect Power/Cable!


Done!
Elapsed: 00:35:25

azhergoga007 · 01-15-2020, 15:12

Operation : Read PatternLock [ v1.16 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ...
Handshake passed!
ID_BLOCK_I : SnapDragon 410 [MSM8916]
ID_BLOCK_S : 26D84E80
ID_BLOCK_L : 05FF9561CC5A47423D12E2E32C77FFCF
ID_BLOCK_L : B3C24CDFD043EB789D583DEAF837212A
Use CM2 Internal Loader
Loader Sent! Initializing ...
Running FireHose on BBID : MSM8916 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x00000003AB400000 [ eMMC 16 GiB ]
ExtInfo : 0x00004000/00004000/00001000/00001000/00000200
Boot Ok!

Read Ok! Trying decrypt ...
PatternLock sequence : 75369

Done!
Elapsed: 00:00:19

Reconnect Power/Cable!

Manikanika81 · 01-15-2020, 19:35

Code:

Operation : Identify [ v2.07 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM_V1632 (Android) (COM146)
MODE : PRELOADER PORT
PORT : 146
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
     CHIP : MT6761 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0200
     TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000005
BROM : SecMode  : SBC+SDA
BROM : PRELOADER PORT
MODE : TECNO : SECURE_v2 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA_SWSEC.bin
AGENT : Found MT6761
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ... 
     DA : AGENT started!
DA : SYNC
     DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

        SRAM: 0x00080000 [ 512,00 KB ]
        DRAM: 0x80000000 [ 2,00 GB ]

        EMMC: 700100464D42434541202723570D9649
        EMMC: VEN : KINGSTON | OEM : 01 | DEV : FMBCEA
        EMMC: 
              BOOT1  : 0x00400000 [ 4,00 MB ]
              BOOT2  : 0x00400000 [ 4,00 MB ]
              RPMB   : 0x00400000 [ 4,00 MB ]
              USER   : 0x74A000000 [ 29,16 GB ]

        CHIP : MT6761 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : 49ED93273F44961F7C33B093DD48B54

DA : USB : HIGH-SPEED

Boot done!

Patch Level    : PPR1.180610.011
Display ID     : KC6-H6114IJK-P-191005V117
Ver. CodeName  : REL
Ver. Release   : 9
Sec. Patch     : 2019-08-05
Build Time     : 1570283400
Product Model  : TECNO KC6
Product Brand  : TECNO
Product Name   : H6114
Product Device : TECNO-KC6
Product Manfct : TECNO MOBILE LIMITED
Product Info   : kc6_h6114
Product Board  : TECNO-KC6
Board Platform : mt6761

USERDATA : ENCRYPTED 


Backup sensetive data [ 10 ]
Backup path : Backup\MT6761__49ED93273F44961F07C33B093DD48B54\
[0] Read : PRELOADER
Backup done!


STORAGE : LifeStatus : Verify NOT supported by DA/HW!

Done!
Elapsed: 00:00:32

Code:

Operation : Reset Settings/Format FS [ v2.07 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM_V1632 (Android) (COM146)
MODE : PRELOADER PORT
PORT : 146
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
     CHIP : MT6761 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0200
     TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000005
BROM : SecMode  : SBC+SDA
BROM : PRELOADER PORT
MODE : TECNO : SECURE_v2 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ... 
AGENT : MTK_AllInOne_DA_SWSEC.bin
AGENT : Found MT6761
AGENT : MTK_DOWNLOAD_AGENT
     BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ... 
     DA : AGENT started!
DA : SYNC
     DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

        SRAM: 0x00080000 [ 512,00 KB ]
        DRAM: 0x80000000 [ 2,00 GB ]

        EMMC: 700100464D42434541202723570D9649
        EMMC: VEN : KINGSTON | OEM : 01 | DEV : FMBCEA
        EMMC: 
              BOOT1  : 0x00400000 [ 4,00 MB ]
              BOOT2  : 0x00400000 [ 4,00 MB ]
              RPMB   : 0x00400000 [ 4,00 MB ]
              USER   : 0x74A000000 [ 29,16 GB ]

        CHIP : MT6761 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : 49ED93273F44961F7C33B093DD48B54

DA : USB : HIGH-SPEED

Boot done!

Format Ok : USERDATA
Format Ok : CACHE
Format Ok : RESET PROTECTION
Format Ok : USERDATA

Done!
Elapsed: 00:00:55

gracy_elec · 01-16-2020, 07:46

SUCCESSFULLY READ NVRAM & BRUSH BAG(LYF-F211S AND:6.0 SP9820E KAIOS)USB

SUCCESS REPORT - [Click to open]

THANKS INFINITY-BOX TEAM

01-15-2020, 11:24	#62035 (permalink)
azhergoga007 No Life Poster Join Date: Jan 2011 Location: lullipapi Posts: 8,670 Member: 1489030 Status: Offline Sonork: 100.1649409 Thanks Meter: 5,368	Remi 5 Plus Mi Acount Reset Doone With King Infinity CM2 Operation : Reset Settings [ v1.16 ] 1. Power Off Phone , Remove battery , Insert back 2. PRESS and HOLD BOTH VOLUME KEYS! 3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode! Wait for phone... Device Found! Initialize ... Handshake passed! ID_BLOCK_I : SnapDragon 625 [MSM8953] ID_BLOCK_S : 52AA2EB6 ID_BLOCK_L : A81172501CEBDD80314B1550C4B64689 ID_BLOCK_L : 7282F85F9EB9A9817EC90AFD7AEC386D Use CM2 Internal Loader Loader Sent! Initializing ... Running FireHose on BBID : MSM8953 , FLASH : eMMC , mVER : 1 MemInfo : 0x0003 / 0x0200 / 0x0000000747C00000 [ eMMC 32 GiB ] ExtInfo : 0x0001C000/00100000/00001000/00001000/00000200 Storage : MFR : 0x45 , VENDOR : SANDISK , NAME : DL2032 Boot Ok! MIAccount reset passed! Device may relock back on WiFi/Network enable! Done! Elapsed: 00:00:22 Reconnect Power/Cable!

01-15-2020, 15:12	#62038 (permalink)
azhergoga007 No Life Poster Join Date: Jan 2011 Location: lullipapi Posts: 8,670 Member: 1489030 Status: Offline Sonork: 100.1649409 Thanks Meter: 5,368	Oppo A37f QLM Pattren Reset Done With Lose Data With King Infinity CM2 Operation : Read PatternLock [ v1.16 ] 1. Power Off Phone , Remove battery , Insert back 2. PRESS and HOLD BOTH VOLUME KEYS! 3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode! Wait for phone... Device Found! Initialize ... Handshake passed! ID_BLOCK_I : SnapDragon 410 [MSM8916] ID_BLOCK_S : 26D84E80 ID_BLOCK_L : 05FF9561CC5A47423D12E2E32C77FFCF ID_BLOCK_L : B3C24CDFD043EB789D583DEAF837212A Use CM2 Internal Loader Loader Sent! Initializing ... Running FireHose on BBID : MSM8916 , FLASH : eMMC , mVER : 1 MemInfo : 0x0003 / 0x0200 / 0x00000003AB400000 [ eMMC 16 GiB ] ExtInfo : 0x00004000/00004000/00001000/00001000/00000200 Boot Ok! Read Ok! Trying decrypt ... PatternLock sequence : 75369 Done! Elapsed: 00:00:19 Reconnect Power/Cable!

01-16-2020, 07:46	#62040 (permalink)
gracy_elec No Life Poster Join Date: Feb 2005 Location: GSM WORLD Posts: 2,079 Member: 118520 Status: Offline Thanks Meter: 3,551	LYF-F211S AND:6.0 SP9820E KAIOS READ NVRAM & BRUSH BAG Done SUCCESSFULLY READ NVRAM & BRUSH BAG(LYF-F211S AND:6.0 SP9820E KAIOS)USB SUCCESS REPORT - [Click to open] Operation : Identify [ v2.04 ] BootMode : FLASH 1. Power off device, wait 10-15 seconds 2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- ) 3. Insert cable in device! Wait for device ... Device Connected! BootVersion : SPRD3 Boot : INF : 0_SC9820E_BASE : SC9820e_eMMC_512MB_RS Sending Init Boot ... Boot sent! Kick FDL ... BootVersion : Spreadtrum Boot Block version 1.1 Protocol setup ... Port speed : 921600 Sending Flash Boot ... Boot sent! Kick FLASH FDL ... FDL : Control transfered! Boot Done! Device info : Patch Level : MRA58K Display ID : LYF-F211S-000-02-14-130619 Ver. Incmt : LYF-F211S-000-02-14-130619 Ver. CodeName : REL Ver. Release : 6.0 Sec. Patch : 2016-07-01 Build Time : 1560422652 Product Model : F211S Product Brand : LYF Product Name : sd208_cww_221 Product Device : sd208_cww_221 Product Board : sd208_cww_221 Product Manfct : Skyworth Board Platform : sp9820e Product Info : sd208_cww_221 Product Model : F211S Update DataBase ... SecInfo : IMEI[1] : 911xxxxxxxxxx32 IMEI[2] : 86xxxxxxxxxxx20 IMEI[3] : 86xxxxxxxxxxx38 WIFIMAC : FFFFFFFFFFFF BT_MAC : FFFFFFFFFFFF SIMLOCK : SignedType UserData : STATE : PLAIN Done! Elapsed: 00:01:18 Operation : Read NVM [ v2.04 ] BootMode : FLASH 1. Power off device, wait 10-15 seconds 2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- ) 3. Insert cable in device! Wait for device ... Device Connected! BootVersion : SPRD3 Boot : INF : 0_SC9820E_BASE : SC9820e_eMMC_512MB_RS Sending Init Boot ... Boot sent! Kick FDL ... BootVersion : Spreadtrum Boot Block version 1.1 Protocol setup ... Port speed : 921600 Sending Flash Boot ... Boot sent! Kick FLASH FDL ... FDL : Control transfered! Boot Done! NVMng : SecurityInfo IMEI[1] : 911xxxxxxxxxx32 IMEI[2] : 86xxxxxxxxxxx20 IMEI[3] : 86xxxxxxxxxxx38 WIFIMAC : FFFFFFFFFFFF BT_MAC : FFFFFFFFFFFF SIMLOCK : SignedType NVMng : Backup Ok , 0x000C61C4 Reconnect Power/Cable! Done! Elapsed: 00:00:31 NOTE : AFTER READ FULL INFO CLOSE TOOL AND REOPEN AND WILL GET YOUR MODEL IN LIST SELECT AND READ BRUSH BAG SUCCESSFULLY(HINT IF GET ERROR PRESS SHIFT KEY TO READ BRUSH BAG) Operation : Read FW [ v2.04 ] Extra : Ignore CriticalPart Verify : Enabled 1. Power off device, wait 10-15 seconds 2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- ) 3. Insert cable in device! Wait for device ... Device Connected! BootVersion : SPRD3 Boot : INF : LYF : F211S Sending Init Boot ... Boot sent! Kick FDL ... BootVersion : Spreadtrum Boot Block version 1.1 Protocol setup ... Port speed : 921600 Sending Flash Boot ... Boot sent! Kick FLASH FDL ... FDL : Control transfered! Boot Done! Device info : Patch Level : MRA58K Display ID : LYF-F211S-000-02-14-130619 Ver. Incmt : LYF-F211S-000-02-14-130619 Ver. CodeName : REL Ver. Release : 6.0 Sec. Patch : 2016-07-01 Build Time : 1560422652 Product Model : F211S Product Brand : LYF Product Name : sd208_cww_221 Product Device : sd208_cww_221 Product Board : sd208_cww_221 Product Manfct : Skyworth Board Platform : sp9820e Product Info : sd208_cww_221 Product Model : F211S AndroidVer : 6 VlnrLevel : 0x02 SP9820E__Skyworth__F211S__6.0__LYF-F211S-000-02-14-130619__MRA58K__sd208_cww_221 Read : u-boot.bin Read : sml.bin Read : tos.bin Read : modem_l.bin Read : ldsp_l.bin Read : gdsp_l.bin Read : nvitem_l.bin Read : modem_wcn.img Read : gnssmodem.bin Read : gnssbdmodem.bin Read : pm_sys.bin Read : boot.img Read : recovery.img Make : persist.img Read : boot_logo.bmp Read : fastboot_logo.bmp Read : system.img ExtSparse : Compression ratio : 32% Make : userdata.img Make : cache.img Read : prodnv.img ExtSparse : Compression ratio : 16% Make : udisk.img Read : deltanv_l.bin Read : phase.cfg Read : u-boot-spl.bin Firmware size : 0x17CC5408 ( 380.77 MiB ) Android Info saved : _Android_info.txt Reconnect Power/Cable! Done! Elapsed: 00:27:53 THANKS INFINITY-BOX TEAM

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Unlocking 5190	Ryu	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	23	01-07-2018 17:14
news headlines to gsm phone	mos	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	7	05-22-2016 11:42
my 8810 is phone locked ,can somebody please help	duyphuc	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	18	12-23-2014 09:03
need software for 5161 by cable	mln2000	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	6	08-29-2010 20:17

01-15-2020, 07:32	#62026 (permalink)
Luckey1 No Life Poster Join Date: Jun 2014 Location: Infinity Box Team Posts: 2,157 Member: 2197212 Status: Offline Sonork: N/A Thanks Meter: 680	Rivo s625 read user code done Operation : Read UserCode [ v1.58 ] 1. Power Off Phone , Remove battery , Insert back 2. Insert USB cable. In some cases require hold BootKey ( '*' ) Wait for phone... Phone found! [ 28 ] Sync... Sync Ok, read regs... Inital regs read done Boot Info : BB_CPU_ID : 6260 BB_CPU_HW : CB00 BB_CPU_SW : 0000 BB_CPU_SB : 8000 BB_CPU_NM : [MediaTek] MT6260_S0000 BB_CPU_SN : 1FCEA5DAB7046724B15CC07534A52415 BROM Protocol Version : 05 Setting... Setting done , result code 0x000E BROM stage done Seek and prepare DownloadAgent DownloadAgent matching HW Found! DA verify and select done Sending DA to target ... InitRes : 00000000 DEV[0] : C800 6000 1800 0000 DEV[1] : 0000 0000 0000 0000 DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B SOC_VERIFY : 0xC1 BOOT_STYLE : SF_FLASH_BOOT NOR Flash IC initialized [0] : FLASH_VEN : 0x00F4 , [GigaDevice] GD25LQ128 [0] : FLASH_DIE : 00C8 0060 0018 0000 [0] : FLASH_LEN : 0x01000000 INT_RAM : 0x0000D000 EXT_RAM : 0x00800000 Read ExtData Sorting ExtData Reading UserCode Active : Yes , Code : 5588 Privacy Lock :6 Done! Elapsed: 00:00:34 Reconnect Power/Cable!