Successfully unlocked/repaired phones by Infinity-Box

[rehmani]

karbon a1+ super format done

Operation : Check / Read Info [ v1.56 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 15 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6571
BB_CPU_NME : [MediaTek] MT6571_S00
BB_CPU_EXT : 0xCA00 , 0x8D00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8B
NAND Flash : 009800BC009000660076001500010000
eMMC Flash : NOT INSTALLED
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0097 , NAND_UNKNOWN
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0015 0001
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
DEV RID    : 0xC1F94A5C1FB4E098F6D0E4B8EB24ECE5
INT RAM    : 0x00020000
EXT RAM    : 0x10000000 [256 MiB]
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : Karbonn A1+ Super
ProdName  : Karbonn A1+ Super
ProdModel : Karbonn A1+ Super
Device    : A1+ Super
AndroidVer: 4.4.2
MTKxCPU   : MT6571
MTKxPRJ   : ALPS.KK1.MP7.V1

SECURITY : 
IMEI_SW [1] : 9113874014-----
IMEI_SW [2] : 9113874014-----
BTMAC Addr  : 3E3846657138
WiFi MAC    : 000000000000

Done!
Elapsed: 00:00:21
Reconnect Power/Cable!


Operation : Format FileSystem [ v1.56 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 15 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6571
BB_CPU_NME : [MediaTek] MT6571_S00
BB_CPU_EXT : 0xCA00 , 0x8D00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8B
NAND Flash : 009800BC009000660076001500010000
eMMC Flash : NOT INSTALLED
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0097 , NAND_UNKNOWN
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0015 0001
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
DEV RID    : 0xC1F94A5C1FB4E098F6D0E4B8EB24ECE5
INT RAM    : 0x00020000
EXT RAM    : 0x10000000 [256 MiB]
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:25
Reconnect Power/Cable!

[rehmani]

micromaxx a110q format done

Chinese Miracle II  [MTK module] v 1.56

Operation : Check / Read Info [ v1.56 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 15 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6583
BB_CPU_NME : [MediaTek] MT6583|6589_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.3.2 on BBID : 0x86
NAND Flash : NOT INSTALLED
eMMC Flash : 204A0190594E49589BA11648EF90E0BE
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , HYNIX
[eMMC] : FLASH_CID : 90014A2058494E594816A19BBEE090EF
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID    : 0xC1F94A5C8629F3C9F4CB9CC0DC48EAAF
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : Micromax
ProdName  : Micromax A110Q
ProdModel : Micromax A110Q
Device    : MicromaxA110Q
AndroidVer: 4.2.1
MTKxCPU   : MT6589
MTKxPRJ   : ALPS.JB2.MP.V1.2

SECURITY : 
IMEI_SW [1] : 91131410600----
IMEI_SW [2] : 91131410615----
BTMAC Addr  : 00738D782E74
WiFi MAC    : 00738D77F058

MODEM : 
BaseBand  : MT6589_S00_MOLY_WR8_W1248_MD_WG_MP_V6_P8

EXTRA : 
LCD [0] : lt5002f_dsi
LCD Res : 854 #800x480 #480
TOUCH [0] : ektf2136
TOUCH [1] : ft5316_5p
TOUCH [2] : GT818B
TOUCH [3] :  
TOUCH [4] : ft5316
CAM [0] : ov8825_mipi_raw
CAM [1] : ov8826_mipi_raw
CAM [2] : ov8827_mipi_raw
CAM [3] : ov2659_yuv
CAM [4] : hi253_yuv
MODEM : tinno89_we_jb2_w1248_mp.v6.p7p8_hspa_850_900_1800_1900_b1_india
LOCALE : en_US hi_IN en_IN de_DE fr_FR es_ES in_ID it_IT ms_MY pt_BR vi_VN tr_TR ar_EG zh_CN hdpi

Done!
Elapsed: 00:00:12
Reconnect Power/Cable!



Operation : Format FileSystem [ v1.56 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 15 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6583
BB_CPU_NME : [MediaTek] MT6583|6589_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.3.2 on BBID : 0x86
NAND Flash : NOT INSTALLED
eMMC Flash : 204A0190594E49589BA11648EF90E0BE
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , HYNIX
[eMMC] : FLASH_CID : 90014A2058494E594816A19BBEE090EF
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID    : 0xC1F94A5C8629F3C9F4CB9CC0DC48EAAF
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:01:09
Reconnect Power/Cable!

[rehmani]

itel it1508c format done

Chinese Miracle II  [SPD module] v 1.27

Set mode to : SP [SC773x] eMMC [Android 6.x]


Operation : Check/Read Info [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 
3. Insert cable

 ====  Wait for phone...

Phone found! [ 78 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ... 

Model Name  : itel_it1508C
Model Brand : Itel
Model Device: itel_it1508C
AndrVersion : 5.1
CompileDate : 6/29/2016 3:59:24 AM
Project Ver : LMY47D release-keys
Model Ext   : itel it1508

ExtraInfo : HWInfo not exists, normal phone

Elapsed: 00:00:30

Reconnect Power/Cable!


Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 
3. Insert cable

 ====  Wait for phone...

Phone found! [ 78 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ... 
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size  : 0x00000001311F7000
State : 0x0001

Mount : /cache
Size  : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x/6.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:37

Reconnect Power/Cable!

[rehmani]

panasonic eluga a2 flash done

Chinese Miracle II  [MTK module] v 1.56

Operation : Check / Read Info [ v1.56 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6737
BB_CPU_NME : [MediaTek] MT6737M|MT6737_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 520001154D423145E3BA0742318E3AC6
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMB1E
[eMMC] : FLASH_CID : 150100524531424D4207BAE3C63A8331
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID    : 0xC1F94A5C5C6D3AD675309D645AF5032C
INT RAM    : 0x00020000
EXT RAM    : 0xC0000000 [3 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : Panasonic
ProdName  : Eluga_A2
ProdModel : Eluga_A2
Device    : Eluga_A2
AndroidVer: 5.1
MTKxCPU   : MT6735
MTKxPRJ   : EB-90S50EA2v1021

SECURITY : 
IMEI_SW [1] : 35159808222----
IMEI_SW [2] : 35159808222----
BTMAC Addr  : 8CC5E14D30A4
WiFi MAC    : 8CC5E14D30A5

MODEM : 
BaseBand  : MT6735_S00_MOLY_LR9_W1444_MD_LWTG_MP_V48_P19_1_lwg_n

EXTRA : 
LCD : Not info available :(
LCD Res : 1280x720
TOUCH [0] : GT1XX
CAM [0] : s5k3h7yx_mipi_raw
CAM [1] : s5k3h7yxdl_mipi_raw
CAM [2] : s5k3h7yxsy_mipi_raw
CAM [3] : ov5670_mipi_raw
CAM [4] : gc5005mipi_raw
MODEM : W_1_8_FDD_3_5_TDD_40_P19
LOCALE : en_US en_IN zh_CN zh_TW es_ES pt_BR ru_RU fr_FR de_DE tr_TR vi_VN ms_MY in_ID th_TH it_IT ar_EG hi_IN bn_IN ur_PK fa_IR pt_PT nl_NL el_GR hu_HU tl_PH ro_RO cs_CZ ko_KR km_KH iw_IL my_MM pl_PL es_US bg_BG hr_HR lv_LV lt_LT sk_SK uk_UA de_AT da_DK fi_FI nb_NO sv_SE en_GB hy_AM zh_HK et_EE ja_JP kk_KZ sr_RS sl_SI ca_ES ne_NP af_ZA zu_ZA sw_TZ en_NZ

Done!
Elapsed: 00:00:13
Reconnect Power/Cable!


Operation : HW Test [ v1.56 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6737
BB_CPU_NME : [MediaTek] MT6737M|MT6737_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 520001154D423145E3BA0742318E3AC6
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMB1E
[eMMC] : FLASH_CID : 150100524531424D4207BAE3C63A8331
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID    : 0xC1F94A5C5C6D3AD675309D645AF5032C
INT RAM    : 0x00020000
EXT RAM    : 0xC0000000 [3 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


[Processing] FlashMemory Read-Write test
[eMMC] : [SAMSUNG] , BMB1E , 0x3A3E00000 , 14910 MiB
[eMMC] : CID : 150100524531424D4207BAE3C63A8331

[eMMC] : MODE : SQ-WR
[PASSED] : eMMC RW Check #1 Ok!
[eMMC] : MODE : RA-WR
[PASSED] : eMMC RW Check #2 Ok!

[eMMC RO CHECK] : eMMC Ok! READ-WRITE Passed!

All Done!

Done!
Elapsed: 00:00:29
Reconnect Power/Cable!


Operation : Read Flash [ v1.56 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6737
BB_CPU_NME : [MediaTek] MT6737M|MT6737_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 520001154D423145E3BA0742318E3AC6
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMB1E
[eMMC] : FLASH_CID : 150100524531424D4207BAE3C63A8331
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID    : 0xC1F94A5C5C6D3AD675309D645AF5032C
INT RAM    : 0x00020000
EXT RAM    : 0xC0000000 [3 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Content now ... 

xGPT : Normalize settings Ok!

Brand     : Panasonic
ProdName  : Eluga_A2
ProdModel : Eluga_A2
Device    : Eluga_A2
AndroidVer: 5.1
MTKxCPU   : MT6735
MTKxPRJ   : EB-90S50EA2v1021

[Read Ok] : preloader_kon6735m_e1_65u_l1.bin
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : logo.bin
[Read Ok] : secro.img
[Read Ok] : tz1.img
[Read Ok] : tz2.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img

[ScatCFG] : MT6737M / V1.1.2 / kon6735m_e1_65u_l1 / EMMC
Android Info saved
MAUI Meta DB saved
HWConfig Info saved
FW Size : 2911 MiB
Scatter saved to : W:\panasonic\eluga a2\v1021\MT6735__Panasonic__Eluga_A2__Eluga_A2__5.1__EB-90S50EA2v1021\

All done!

Done!
Elapsed: 00:11:21
Reconnect Power/Cable!


Scatter Load Ok , BaseBand : MT6737 , Project : kon6735m_e1_65u_l1 , Storage : EMMC
Files found : 11 , Set to Flash : 10
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand   : Panasonic
Device Model   : Eluga_A2
Device CPU     : MT6735
Device IntName : Eluga_A2
Device Version : 5.1
Device Compile : 9/6/2016 12:51:43 AM
Device Project : EB-90S50EA2v1017
Device ExtInfo : Eluga_A2
Ready to Flash!

Operation : Flash [ v1.56 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6737
BB_CPU_NME : [MediaTek] MT6737M|MT6737_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 520001154D423145E3BA0742318E3AC6
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMB1E
[eMMC] : FLASH_CID : 150100524531424D4207BAE3C63A8331
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID    : 0xC1F94A5C5C6D3AD675309D645AF5032C
INT RAM    : 0x00020000
EXT RAM    : 0xC0000000 [3 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6737 , Project : kon6735m_e1_65u_l1 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Enabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 4138 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000001C80000-0x0000000004D80000
Erase : 0x0000000006B00000-0x000000039C280000
Flash Pre-Erase Done, time used : 00:00:01

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ... 
Use : preloader_kon6735m_e1_65u_l1.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0016
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : TEE1
Image Flash Ok
Flash now : TEE2
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:06:20

Processing : Verify
Verify Passed : LK
Verify Passed : BOOT
Verify Passed : RECOVERY
Verify Passed : LOGO
Verify Passed : SECRO
Verify Passed : TEE1
Verify Passed : TEE2
Verify Passed : SYSTEM
Verify Passed : CACHE
Verify Passed : USERDATA
Data Verify Done, time used : 00:01:53

Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:08:29
Reconnect Power/Cable!

[rehmani]

panasonic ez240 format done

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 80 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ... 
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0000
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Verify data... Can take some time
Init Ok, formatting DIN area ... 
Format Block Done!
Done!

Elapsed: 00:00:21

Reconnect Power/Cable!

[rehmani]

karnbon k9 smart flash done

Chinese Miracle II  [MTK module] v 1.56

Operation : Check / Read Info [ v1.56 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 700100563130303038502EA2B40E43D9
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x70 , OEM : 0100
[eMMC] : FLASH_INF : [KINGSTON] , 80001
[eMMC] : FLASH_CID : 700100563130303038502EA2B40E43D9
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001C3000000
[eMMC] : FLASH_UCP : 7216 MiB [eMMC 8 GiB]
DEV RID    : 0xC1F94A5CD7E38485E85C5216ADDDA2E7
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : Karbonn
ProdName  : K9Smart
ProdModel : K9 Smart
Device    : K9Smart
AndroidVer: 4.4.2
MTKxCPU   : MT6572
MTKxPRJ   : ALPS.KK1.MP7.V1

MODEM : 
BaseBand  : MT6572_S00_MOLY_WR8_W1315_MD_WG_MP_V43_1_wg_n

EXTRA : 
LCD [0] : hx8379c_bld_hsd
LCD [1] : ili9806e_txd_hsd
LCD [2] : ili9806e_dj_new_hsd
LCD [3] : ili9806e_dj_hsd
LCD Res : 854x480
TOUCH [0] : msg2xxx
CAM [0] : gc2145_mipi_yuv
CAM [1] : gc0312_yuv
CAM [2] : gc0329_yuv
MODEM : vsun72_w_kk_hspa_dual900_1band
LOCALE : hi_IN bn_BD gu_IN mr_IN pa_IN ur_PK kn_IN ml_IN as_IN or_IN te_IN ta_IN my_IN si_LK mr_IN pa_IN bn_IN  ta_IN  en_US  es_ES pt_BR ru_RU fr_FR de_DE tr_TR vi_VN ms_MY in_ID th_TH it_IT ar_EG fa_IR pt_PT nl_NL el_GR hu_HU tl_PH ro_RO cs_CZ ko_KR km_KH iw_IL my_MM pl_PL es_US bg_BG hr_HR lv_LV lt_LT sk_SK uk_UA de_AT da_DK fi_FI nb_NO sv_SE en_GB hy_AM et_EE ja_JP kk_KZ sr_RS sl_SI ca_ES hdpi

Done!
Elapsed: 00:00:11
Reconnect Power/Cable!


Scatter Load Ok , BaseBand : MT6572 , Project : vsun72_w_kk , Storage : EMMC
Files found : 11 , Set to Flash : 10
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand   : Karbonn
Device Model   : K9Smart
Device CPU     : MT6572
Device IntName : K9Smart
Device Version : 4.4.2
Device Compile : 3/4/2016 5:59:15 AM
Device Project : ALPS.KK1.MP7.V1
Device ExtInfo : K9 Smart
Ready to Flash!

Operation : Flash [ v1.56 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 700100563130303038502EA2B40E43D9
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x70 , OEM : 0100
[eMMC] : FLASH_INF : [KINGSTON] , 80001
[eMMC] : FLASH_CID : 700100563130303038502EA2B40E43D9
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001C3000000
[eMMC] : FLASH_UCP : 7216 MiB [eMMC 8 GiB]
DEV RID    : 0xC1F94A5CD7E38485E85C5216ADDDA2E7
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6572 , Project : vsun72_w_kk , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Disabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 3694 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000000C00000-0x0000000000100000
Erase : 0x0000000002900000-0x00000001BFE00000
Flash Pre-Erase Done, time used : 00:00:01

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ... 
Use : preloader_vsun72_w_kk.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0012
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : MBR
Image Flash Ok
Flash now : EBR1
Image Flash Ok
Flash now : UBOOT
Image Flash Ok
Flash now : BOOTIMG
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SEC_RO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : ANDROID
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USRDATA
Image Flash Ok
Flash Write Done, time used : 00:02:02


Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:02:19
Reconnect Power/Cable!

[Sajjad_Hussain]

[rehmani]

micromaxx q340 flash done

Chinese Miracle II  [MTK module] v 1.56

Operation : Check / Read Info [ v1.56 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4838473165050781A11C1E6287
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e1G8
[eMMC] : FLASH_CID : 90014A4838473165050781A11C1E6287
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0xC1F94A5C82788D9431E3EBE9DB7EF054
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : Micromax
ProdName  : Q340
ProdModel : Micromax Q340
Device    : Q340
AndroidVer: 5.0
MTKxCPU   : MT6582
MTKxPRJ   : ALPS.L0.MP2.V1_TINNO6582.WT.L_P7

SECURITY : 
IMEI_SW [1] : 91144075114----
IMEI_SW [2] : 91144075164----
BTMAC Addr  : A0F8956EA61B
WiFi MAC    : A0F8956EC16F

MODEM : 
BaseBand  : MT6582_S00_MOLY_WR8_W1449_MD_WG_MP_V1_P3_1_wg_n

EXTRA : 
LCD [0] : ili9806e_fwvga_dsi_vdo_tcl
LCD [1] : otm8019a_fwvga_dsi_vdo_boe
LCD Res : 854x480
TOUCH [0] : GT9XX_S5222
TOUCH [1] : EKTF2K_S5222
CAM [0] : ov5648_mipi_raw_darling
CAM [1] : ov5648_mipi_raw_sunwin
CAM [2] :  ov2680_mipi_raw_sunwin gc0310_mipi_yuv ov2680_mipi_raw_cmk ov5670_mipi_raw
MODEM : mt6582_hspa_gemini_gms4_b1b8_mmx_in
LOCALE : en_US en_IN hi_IN mr_IN bn_IN kn_IN te_IN ta_IN ml_IN gu_IN pa_IN or_IN de_DE fr_FR es_ES in_ID it_IT ms_MY pt_BR vi_VN tr_TR ar_EG zh_CN fa_IR ar_EG es_ES fr_FR ru_RU ro_RO hdpi

Done!
Elapsed: 00:00:08
Reconnect Power/Cable!


Operation : HW Test [ v1.56 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4838473165050781A11C1E6287
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e1G8
[eMMC] : FLASH_CID : 90014A4838473165050781A11C1E6287
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0xC1F94A5C82788D9431E3EBE9DB7EF054
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


[Processing] FlashMemory Read-Write test
[eMMC] : [HYNIX] , e1G8 , 0x1D2000000 , 7456 MiB
[eMMC] : CID : 90014A4838473165050781A11C1E6287

[eMMC] : MODE : SQ-WR
[PASSED] : eMMC RW Check #1 Ok!
[eMMC] : MODE : RA-WR
[PASSED] : eMMC RW Check #2 Ok!

[eMMC RO CHECK] : eMMC Ok! READ-WRITE Passed!

All Done!

Done!
Elapsed: 00:00:49
Reconnect Power/Cable!


Scatter Load Ok , BaseBand : MT6582 , Project : s5222 , Storage : EMMC
Files found : 11 , Set to Flash : 10
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand   : Micromax
Device Model   : Q340
Device CPU     : MT6582
Device IntName : Q340
Device Version : 5.0
Device Compile : 7/7/2015 1:36:25 AM
Device Project : ALPS.L0.MP2.V1_TINNO6582.WT.L_P7
Device ExtInfo : Micromax Q340
Ready to Flash!

Operation : Flash [ v1.56 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4838473165050781A11C1E6287
Initialize Memory ... 
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e1G8
[eMMC] : FLASH_CID : 90014A4838473165050781A11C1E6287
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0xC1F94A5C82788D9431E3EBE9DB7EF054
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6582 , Project : s5222 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Disabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 3712 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000000C00000-0x0000000000100000
Erase : 0x0000000002900000-0x00000001CEE00000
Flash Pre-Erase Done, time used : 00:00:03

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ... 
Use : preloader_s5222.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0012
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : MBR
Image Flash Ok
Flash now : EBR1
Image Flash Ok
Flash now : UBOOT
Image Flash Ok
Flash now : BOOTIMG
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SEC_RO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : ANDROID
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USRDATA
Image Flash Ok
Flash Write Done, time used : 00:04:36


Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:04:51
Reconnect Power/Cable!

[azhergoga007]

Card found: S/N : A19EC787 , v0136
Chinese Miracle II [SPD module] v 1.27

Set mode to : SP [SC773x] eMMC [Android 5.x]

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

==== Wait for phone...

Phone found! [ 30 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC773x Android 5.x eMMC v1.0 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size : 0x00000000845F7000
State : 0x0001

Mount : /cache
Size : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Done!

Elapsed: 00:00:24

Reconnect Power/Cable!

[UnlockwithCode]

.::SUCCSESSFULL PATTERN LOCK REMOVE MMX Q465 WITH CM2::.

Card found: S/N : xxxxxxxx , v0136
Chinese Miracle II [SPD module] v 1.27

Set mode to : SP [SC983x] eMMC [Generic Android 5.x]

Operation : Check/Read Info [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

==== Wait for phone...

Phone found! [ 37 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC9830 eMMC Generic Loader v2 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name : Q465
Model Brand : Micromax
Model Device: Q465
AndrVersion : 5.1
BaseBand CPU: ZSL859P_MMX
CompileDate : 6/2/2016 12:53:48 PM
Project Ver : MMX_Q465_SW_V8.0.7_HW_V1.0.0_020616
Model Ext : Micromax Q465

ExtraInfo : HWInfo not exists, normal phone

Elapsed: 00:00:24

Reconnect Power/Cable!


Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

==== Wait for phone...

Phone found! [ 37 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC9830 eMMC Generic Loader v2 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size : 0x00000002DC8F7000
State : 0x0001

Mount : /cache
Size : 0x0000000008F0D000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x/6.x : Reset FRP Lock
Reset Ok!


Done!

Elapsed: 00:00:25

Reconnect Power/Cable!


Br:
Unlockwithcode

[azhergoga007]

Card found : S/N : A19EC787 , v0136
Chinese Miracle II [MTK module] v 1.58

Scatter Load Ok , BaseBand : MT6582 , Project : s5400 , Storage : EMMC
Files found : 11 , Set to Flash : 10
Ready to Flash!

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 19 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A483847316505070B97ECEB42DD
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e1G8
[eMMC] : FLASH_CID : 90014A483847316505070B97ECEB42DD
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0xD9C8F39511221172A699E05C75EC2965
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6582 , Project : s5400 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 3843 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000000C00000-0x0000000000100000
Erase : 0x0000000002900000-0x00000001CEE00000
Flash Pre-Erase Done, time used : 00:00:06

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_s5400.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0012
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : MBR
Image Flash Ok
Flash now : EBR1
Image Flash Ok
Flash now : UBOOT
Image Flash Ok
Flash now : BOOTIMG
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SEC_RO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : ANDROID
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USRDATA
Image Flash Ok
Flash Write Done, time used : 00:04:02

Processing : Verify
Verify Passed : MBR
Verify Passed : EBR1
Verify Passed : UBOOT
Verify Passed : BOOTIMG
Verify Passed : RECOVERY
Verify Passed : SEC_RO
Verify Passed : LOGO
Verify Passed : ANDROID
Verify Passed : CACHE
Verify Passed : USRDATA
Data Verify Done, time used : 00:01:25

Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:05:46
Reconnect Power/Cable!

[azhergoga007]

Set mode to : [AltLDR] SP [SC773x] eMMC [Android 5.x]

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

==== Wait for phone...

Phone found! [ 30 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v4 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size : 0x0000000180000000
State : 0x0001

Mount : /cache
Size : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Done!

Elapsed: 00:00:32

Reconnect Power/Cable!

[azhergoga007]

Card found : S/N : A19EC787 , v0136
Chinese Miracle II [MTK module] v 1.58

Operation : Read UserCode [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )

Wait for phone...
Phone found! [ 10 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6261
BB_CPU_HW : CB01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6261_S0000
BB_CPU_SN : 0642326C87481E9F3867ABE6AB9C78BC
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8E
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x0113 , [Winbond] SF_W25Q32JV
[0] : FLASH_DIE : 00EF 0070 0016 0000
[0] : FLASH_LEN : 0x00400000
SDS_INFO : 0x003FE000 , 0x00002000
INT_RAM : 0x0000D000
EXT_RAM : 0x00400000

Read ExtData
Sorting ExtData
Reading UserCode

Active : Yes , Code : 2233

PLock|MobTrack : Not active

Done!
Elapsed: 00:00:06
Reconnect Power/Cable!

[rehmani]

intex aqua eco 4g flash done

Chinese Miracle II  [SPD module] v 1.27

Set mode to : SP [SC773x] eMMC [Android 5.x]

Operation : Check/Read Info [ v1.27 ]

1. Remove battery. Insert battery back
2. Insert cable
3. In case of SVC init problems - connect with hold "VolDown" button!

 ====  Wait for phone...

Phone found! [ 80 ]
Port Opened
Sync...
InitSvc Done
Wait for phone...
Sync...
Phone Initial Info : 
Platform : MOCORTM_W15.7.2_Debug
Project  : sharkl_cp1
HWInfo   : sc9830_modem
Phone Security Info : 
IMEI [1] : 3507775aaA91152
IMEI [2] : 3507775bcd00000
BT_ADDR  : 000000000000
SelfInfo : 
BatVoltage : 3.644 V

Done

Reconnect Power/Cable!

Set mode to : SP [SC983x] eMMC [Generic Android 5.x]

Operation : Check/Read Info [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 
3. Insert cable

 ====  Wait for phone...

Phone found! [ 79 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC9830 eMMC Generic Loader v2 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ... 

Model Name  : sp9830aef5mvolteoversea
Model Brand : Aqua_Eco_4G
Model Device: sp9830aef_5m_volte
AndrVersion : 5.1
BaseBand CPU: SP9830AEF_5M_VOLTE
CompileDate : 6/24/2016 4:15:42 AM
Project Ver : Intex_Aqua_Eco_4G_V08_Indian
Model Ext   : Aqua_Eco_4G

ExtraInfo : HWInfo exists!!! This phone have DYNAMIC HW settings!!!

Elapsed: 00:00:42

Reconnect Power/Cable!


Operation : Read NV [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 
3. Insert cable

 ====  Wait for phone...

Phone found! [ 79 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC9830 eMMC Generic Loader v2 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Detected eMMC Flash , Structure detect Ok!

Read LTEx NV #1

Read Ok , 0x1AC28
Saved to : C:\InfinityBox\CM2SPD\phdata\backup\intex aqua eco 4g sc983x emmc gen and5.x

Elapsed: 00:01:06

Reconnect Power/Cable!


Loading    : Intex_Aqua_Eco_4G_V08_Indian_SER.pac
CRVersion  : BP_R1.0.0
PacCPUinfo : SharkL5ModeMarlinAndroid5.1
PacVersion : Intex_Aqua_Eco_4G_V08_Indian_SER
FastCheck  : 0x004DAE4F43


Operation : Flash [ v1.27 ]

======= Flash
Files set for flashing : 
[ MCU ] : Intex_Aqua_Eco_4G_V08_Indian_SER.pac
CRVersion  : BP_R1.0.0
PacCPUinfo : SharkL5ModeMarlinAndroid5.1
PacVersion : Intex_Aqua_Eco_4G_V08_Indian_SER
File : fdl1.bin
File : fdl2.bin
File : nvitem.bin
File : prodnv.img
File : u-boot-spl-16k.bin
File : SC9600_sharkl_5modcsfb_volte.bin
File : LTE_DSP.bin
File : SHARKL_DM_DSP.bin
File : SC9600_sharkl_wphy_5mod_volte.bin
File : PM_sharkl_arm7_dfs.bin
File : fdl1.bin(1)
File : EXEC_KERNEL_IMAGE0.bin
File : boot.img
File : recovery.img
File : system.img
File : oem.img
File : userdata.img
File : logo_wvga_intex.bmp
File : logo_wvga_intex.bmp(1)
File : cache.img
File : u-boot.bin
File : persist.img
File : udc.bin

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 
3. Insert cable

 ====  Wait for phone...

Phone found! [ 79 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
PMTManager : Load 0x27 records
PMTManager : PMT Update Ok!
Flashing now

[FlashProc] : CODE  
Current ID : PRODNV
Current File : prodnv.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : ERASEUBOOT
Current Part : uboot
[FlashProc] : Ok!

[FlashProc] : BOOTCODE
Current ID   : SPLLOADER
Current File : u-boot-spl-16k.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : MODEM_WLTE
Current File : SC9600_sharkl_5modcsfb_volte.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : DSP_WLTE_LTE
Current File : LTE_DSP.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : DSP_WLTE_GGE
Current File : SHARKL_DM_DSP.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : WARM_WLTE
Current File : SC9600_sharkl_wphy_5mod_volte.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : DFS
Current File : PM_sharkl_arm7_dfs.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : FDL_WCN
Current File : fdl1.bin(1)
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : MODEM_WCN
Current File : EXEC_KERNEL_IMAGE0.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : BOOT
Current File : boot.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : RECOVERY
Current File : recovery.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : SYSTEM
Current File : system.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : OEM
Current File : oem.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : USERDATA
Current File : userdata.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : BOOTLOGO
Current File : logo_wvga_intex.bmp
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : FASTBOOT_LOGO
Current File : logo_wvga_intex.bmp(1)
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : CACHE
Current File : cache.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : FLASH_WLTE
Current Part : l_runtimenv1
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : ERASEMISC
Current Part : misc
[FlashProc] : Ok!

[FlashProc] : BOOTCODE
Current ID   : UBOOTLOADER
Current File : u-boot.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : PERSIST
Current File : persist.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : UDC_CONFIG
Current File : udc.bin
Flashing now ... 
[FlashProc] : Ok!


Elapsed: 00:02:02

Reconnect Power/Cable!

[khawajagsm]

Infinity-Box LG Service Tool [ LGS ] v1.03

Operation : Reset Settings/Format FS [ v1.03 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD VOLUME UP KEY!
3. Insert USB cable, wait until Download mode screen will appear

Wait for phone...
Connection opened successfully!
Waiting for loader ...
Handshake passed!
Collect info...
Prepare passed, mode 0x01
Boot done!

Format UserData
Format Cache
Format done
Erase FRP#3 block Ok!

Reconnect Power/Cable!

Done!
Elapsed: 00:00:41