Voice v40 write flash error - GSM-Forum

sanyomobile · 06-13-2015, 11:17

Operation : Flash [ v1.21 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 46 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 7001004D4D43303447020240C72C700D
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0070 , OEM : 0100
[eMMC] : FLASH_INF : G40CM
[eMMC] : FLASH_CID : 7001004D4D43303447020240C72C700D
[eMMC] : FLASH_LEN : 0x00000000E2C00000
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6572 , Project : wt97512 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000000600000-0x0000000000100000
Erase : 0x0000000002300000-0x00000000DF820000
Flash Pre-Erase Done, time used : 00:00:22

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_wt97512.bin
Preloader Init Failed! Looks like HW error or incompatible image

i read this file with cm2 but now its not writing

JayDi · 06-13-2015, 12:13

Erase flash fully, then try again.

sanyomobile · 06-13-2015, 12:55

also erase full flash but same problem

JayDi · 06-13-2015, 13:00

Error seems as "Not enough space for init" or something similar. What error says SPFT?

sanyomobile · 06-13-2015, 13:07

same error with other one.............

JayDi · 06-13-2015, 14:55

What same? Did you even read my messages?

kabul · 06-13-2015, 15:15

Voice V40 already Read write successful report
maybe hardware problem

http://forum.gsmhosting.com/vbb/11035565-post1275.html
http://forum.gsmhosting.com/vbb/11095784-post1661.html

06-13-2015, 11:17	#1 (permalink)
sanyomobile No Life Poster Join Date: Oct 2012 Posts: 1,436 Member: 1824929 Status: Offline Thanks Meter: 99	Voice v40 write flash error Operation : Flash [ v1.21 ] ======= Flash 1. Power Off Phone , Remove battery , Insert back 2. Insert USB cable. In some cases require hold BootKey Wait for phone... Phone found! [ 46 ] Sync... Inital regs read done Boot Info : BB_CPU_ID : 6572 BB_CPU_HW : CA01 BB_CPU_SW : 8A00 BB_CPU_SB : 0000 BB_CPU_NM : [MediaTek] MT6572_S00 Processing BROM stage BLVersion : 0x01 SecCfgVal : 0x00000000 BromVersion : 0xFF BLVersion : 0x01 Preloader Status : Alive Processing DA stage DA Select done , sending NAND_ID : 00000000000000000000000000000000 eMMC_ID : 7001004D4D43303447020240C72C700D DA Stat : v4.2 on BBID : 0x88 DA Sent. Configure setting now ... DA started successuflly eMMC FlashIC initialized [eMMC] : FLASH_VEN : 0070 , OEM : 0100 [eMMC] : FLASH_INF : G40CM [eMMC] : FLASH_CID : 7001004D4D43303447020240C72C700D [eMMC] : FLASH_LEN : 0x00000000E2C00000 INT RAM : 0x00020000 EXT RAM : 0x20000000 BOOT TYPE : EMMC_FLASH_BOOT SOC VERIFY : C1 Boot Ok! ScatCFG : BaseBand : MT6572 , Project : wt97512 , Storage : EMMC Setting : Flash Pre-Erase (Safe) : Enabled Setting : AFF verify : Enabled BL : Check HW compatibility BL : BBID supported by BootLoader! BL : Check eMMC compatibility BL : eMMC supported by BootLoader! BL : Flash Pre-Erase Total blocks to Erase : 2 Erase : 0x0000000000600000-0x0000000000100000 Erase : 0x0000000002300000-0x00000000DF820000 Flash Pre-Erase Done, time used : 00:00:22 SecCfg Passed , 1799 BMT remark not need. Will skip Sending Preloader ... Use : preloader_wt97512.bin Preloader Init Failed! Looks like HW error or incompatible image i read this file with cm2 but now its not writing

06-13-2015, 12:13	#2 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	Erase flash fully, then try again.

06-13-2015, 12:55	#3 (permalink)
sanyomobile No Life Poster Join Date: Oct 2012 Posts: 1,436 Member: 1824929 Status: Offline Thanks Meter: 99	also erase full flash but same problem

06-13-2015, 13:00	#4 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	Error seems as "Not enough space for init" or something similar. What error says SPFT?

06-13-2015, 13:07	#5 (permalink)
sanyomobile No Life Poster Join Date: Oct 2012 Posts: 1,436 Member: 1824929 Status: Offline Thanks Meter: 99	same error with other one.............

06-13-2015, 14:55	#6 (permalink)
JayDi No Life Poster Join Date: Mar 2007 Location: Where you live Posts: 18,542 Member: 462970 Status: Offline Thanks Meter: 20,352	What same? Did you even read my messages?

06-13-2015, 15:15	#7 (permalink)
kabul No Life Poster Join Date: Jan 2007 Posts: 4,633 Member: 433097 Status: Offline Sonork: 100.1661890 Thanks Meter: 8,074	Voice V40 already Read write successful report maybe hardware problem http://forum.gsmhosting.com/vbb/11035565-post1275.html http://forum.gsmhosting.com/vbb/11095784-post1661.html