Nokia BB5 Flash Reball by CHARAN ORISSA - GSM-Forum

charan orissa · 06-30-2011, 13:39

Stacked chip of NOKIA Phones

Here two chip are stacked
i. RAPS
ii. FLASH

TO REBALL FLASH

1.Put big nozzle on hot air to lift up. apply flux as needed. Use good quality flux.Otherwise may damage Chip. Do it carefully and slowly that there is no mistake in the work.

The 1st is Flash and second is RAPs

clean all leadfree materials on pcb and on chip. this should be done perfectly,
in order to get perfectly joint contact on our next reballing with leaded tin paste.

there is nothing special when reballing on lower part (rap to pcb side).

2. Now, reball flash and repet the process till correct ball size.

Put it on rap. again, use big nozzle on hot air. lower temp, lower air flow.

Now your phone is ready.

Prec.
1. Back all rpl
2. Back all certificates
3. Back all PM

After reball phone may be in test/local mode
Then, Flash it with latest firmware, restor all cert,rpl,PM do rfbb tune, dcc if needed.

Thanks to gbluez for photograph/adv Manole and also that persons according to whome there is no flash chip on N5130.

And special thanks to my big Br ripgsm

N.B. I am not responsible for any damage coused by this procdure. I post here only my work by which I succed in many times.

alkhaleejmobile · 06-30-2011, 14:31

dear post in hardware section

charan orissa · 07-02-2011, 19:55

Quote:

Originally Posted by charan orissa

nokia flash reball by charan orissa

nokia flash reball by charan orissa

nokia flash reball by charan orissa

stacked chip of nokia phones

here two chip are stacked
i. Raps
ii. Flash

to reball flash

1.put big nozzle on hot air to lift up. Apply flux as needed. Use good quality flux.otherwise may damage chip. Do it carefully and slowly that there is no mistake in the work.

the 1st is flash and second is raps

clean all leadfree materials on pcb and on chip. This should be done perfectly,
in order to get perfectly joint contact on our next reballing with leaded tin paste.

There is nothing special when reballing on lower part (rap to pcb side).

2. Now, reball flash and repet the process till correct ball size.

put it on rap. Again, use big nozzle on hot air. Lower temp, lower air flow.

now your phone is ready.

prec.
1. Back all rpl
2. Back all certificates
3. Back all pm

after reball phone may be in test/local mode
then, flash it with latest firmware, restor all cert,rpl,pm do rfbb tune, dcc if needed.

thanks to gbluez for photograph/adv manole and also that persons according to whome there is no flash chip on n5130.

And special thanks to my big br ripgsm

n.b. I am not responsible for any damage coused by this procdure. I post here only my work by which i succed in many times.

nokia flash reball by charan orissa

charan orissa · 07-14-2011, 19:59

Quote:

Originally Posted by charan orissa

nokia flash reball by charan orissa

100%work.......................................... ...........................................

GSM boy · 07-14-2011, 22:11

hard and good work keep it man

realy good post

rabirabi · 07-15-2011, 03:32

plz upload video so that everyone get knowledge and u will be awarded. thanx 4 ur info.

cilunkz · 07-15-2011, 14:03

nice job gan.this is great.

kk_amata · 07-16-2011, 01:26

thank.nice workshop.

**Wites OM Tesla** · 09-10-2011, 21:00

Nice job but i reboll without any kind of matrix.
And i call this flash on top of processor Sandwich.

alyasjee · 08-02-2012, 21:41

hello sir , thanks for the suggestion but i got a problem while i bring out this chip few points r missing down on pcb how do i recover them ? i have tried one thing ! i drilled them little then i fill solder in there after doing this with all 7 points of pcb i reball the chip n place it back but now facing problem , phone memory full...

**Wites OM Tesla** · 08-05-2012, 10:38

Quote:

Originally Posted by alyasjee

hello sir , thanks for the suggestion but i got a problem while i bring out this chip few points r missing down on pcb how do i recover them ? i have tried one thing ! i drilled them little then i fill solder in there after doing this with all 7 points of pcb i reball the chip n place it back but now facing problem , phone memory full...

Try to restore phone to last version,and no need to drill some print are null not needed.
Chk here like in iphone 4 Before Open a Thread Search Here Hardware Solutions!

alyasjee · 08-14-2012, 14:29

thank you very much for paying attention and for the best suggestion of the year

i did the same as seen in the pictures thanks again

06-30-2011, 13:39	#1 (permalink)
charan orissa Freak Poster Join Date: Feb 2011 Location: BARGARH , ORISSA , INDIA Posts: 428 Member: 1524542 Status: Offline Sonork: 100.1607125 Thanks: 346 Thanked 90 Times in 58 Posts	Nokia BB5 Flash Reball by CHARAN ORISSA Stacked chip of NOKIA Phones Here two chip are stacked i. RAPS ii. FLASH TO REBALL FLASH 1.Put big nozzle on hot air to lift up. apply flux as needed. Use good quality flux.Otherwise may damage Chip. Do it carefully and slowly that there is no mistake in the work. The 1st is Flash and second is RAPs clean all leadfree materials on pcb and on chip. this should be done perfectly, in order to get perfectly joint contact on our next reballing with leaded tin paste. there is nothing special when reballing on lower part (rap to pcb side). 2. Now, reball flash and repet the process till correct ball size. Put it on rap. again, use big nozzle on hot air. lower temp, lower air flow. Now your phone is ready. Prec. 1. Back all rpl 2. Back all certificates 3. Back all PM After reball phone may be in test/local mode Then, Flash it with latest firmware, restor all cert,rpl,PM do rfbb tune, dcc if needed. Thanks to gbluez for photograph/adv Manole and also that persons according to whome there is no flash chip on N5130. And special thanks to my big Br ripgsm N.B. I am not responsible for any damage coused by this procdure. I post here only my work by which I succed in many times.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
New Nokia Software!!!!!!!	Jefferson	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	73	05-15-2013 13:07
Need software upgrade for Nokia 5110	ptkrf	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	26	09-25-2012 02:41
Seeking for flash nokia 5110 old version (3 version) can exchange for new	Tomas	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	7	11-17-2011 17:08

06-30-2011, 14:31	#2 (permalink)
alkhaleejmobile No Life Poster Join Date: Nov 2008 Location: saudi arabia Posts: 2,924 Member: 904809 Status: Offline Sonork: 100.1615464 Thanks: 89 Thanked 598 Times in 392 Posts	dear post in hardware section

07-14-2011, 22:11	#5 (permalink)
GSM boy Freak Poster Join Date: Aug 2010 Age: 3 Posts: 326 Member: 1375690 Status: Offline Thanks: 301 Thanked 96 Times in 53 Posts	hard and good work keep it man realy good post

07-15-2011, 03:32	#6 (permalink)
rabirabi Freak Poster Join Date: Jun 2009 Location: Nepal Posts: 385 Member: 1061924 Status: Offline Sonork: 100.1612111 Thanks: 49 Thanked 65 Times in 43 Posts	plz upload video so that everyone get knowledge and u will be awarded. thanx 4 ur info.

07-15-2011, 14:03	#7 (permalink)
cilunkz Junior Member Join Date: May 2008 Posts: 11 Member: 767328 Status: Offline Sonork: cilunkz Thanks: 2 Thanked 2 Times in 2 Posts	nice job gan.this is great.

07-16-2011, 01:26	#8 (permalink)
kk_amata Crazy Poster Join Date: Oct 2006 Posts: 50 Member: 377308 Status: Offline Thanks: 3 Thanked 6 Times in 4 Posts	thank.nice workshop.

09-10-2011, 21:00	#9 (permalink)
Wites OM Tesla Moderator Join Date: Apr 2009 Location: Moldova,Chisinau. Age: 27 Posts: 3,433 Member: 1017374 Status: Online Thanks: 68 Thanked 2,439 Times in 972 Posts	Nice job but i reboll without any kind of matrix. And i call this flash on top of processor Sandwich.

08-02-2012, 21:41	#10 (permalink)
alyasjee Freak Poster Join Date: Mar 2012 Location: Bahrain Posts: 101 Member: 1739869 Status: Offline Thanks: 17 Thanked 8 Times in 7 Posts	hello sir , thanks for the suggestion but i got a problem while i bring out this chip few points r missing down on pcb how do i recover them ? i have tried one thing ! i drilled them little then i fill solder in there after doing this with all 7 points of pcb i reball the chip n place it back but now facing problem , phone memory full...

08-14-2012, 14:29	#12 (permalink)
alyasjee Freak Poster Join Date: Mar 2012 Location: Bahrain Posts: 101 Member: 1739869 Status: Offline Thanks: 17 Thanked 8 Times in 7 Posts	thank you very much for paying attention and for the best suggestion of the year i did the same as seen in the pictures thanks again