ERSERV 1.7 ' Failed to enter sp mode ' - GSM-Forum

ptkrf · 05-14-1999, 21:21

I have a problem:

I use Victor Levunliev cable for 17 digit IMEI for Ericsson GA628, but the new series is very hard to unlock
IMEI number is 520018-61-379938-9-05, Program version is 9901131158 & CXC125056
Hardware revision is: 99W15 KRC 114 278/40 R2E
This type oh phone is year 1999

Problem: When I start erserv 1.7 and check any command (not sp-unlock this tampered the pohone checked) the prog says
'Failed to enter sp mode' and the phon power up.

I tray to use with zulea ericload prg says 'error port set' and ericflesh prog says ' time out ...'

can you still help me

Manfred

sc~micro · 05-15-1999, 17:14

I had the same problem once.
Try new cable.
Get schematics from 'mobile.8m.com'

ptkrf · 05-15-1999, 17:44

thanks, but still don't work

Manfred

Melorien · 05-18-1999, 15:01

Easy when you connect the phone and will enter the test mode you have to push the no buttom quick not hold it in 1 of a 10 pice of a sec.
If not check pin 9 it must have the 5V.
Dalton

ptkrf · 05-18-1999, 17:26

Hi guys, thanks but the problem is the phone!
hardware interface and cable works great on older phones, even on phones manufactured in 99' but the IMEI number MUST be lower then 52****-61-******-*-**, ERSERV 1.3 (1.7...) works great, if IMEI start on number 490***, here is what hapend when use erserv:

Ericsson 6xx or 7xx detected
Enter TEST Mode ...
Failed to enter sp mode ...

then the phone power up

The only way for new phone to be accepted with erserv 1.3 or Zulea dos programs, must be TAMPERED, then the programs work fine !!!!

Who now how to make the phone TAMPERED if not accepted with erserv 1.3 or Zulea dos programs ?????

please help me....

thanks Manfred

05-14-1999, 21:21	#1 (permalink)
ptkrf Freak Poster Join Date: May 1999 Location: in my mind Age: 45 Posts: 301 Member: 17 Status: Offline Thanks: 2 Thanked 6 Times in 2 Posts	ERSERV 1.7 ' Failed to enter sp mode ' I have a problem: I use Victor Levunliev cable for 17 digit IMEI for Ericsson GA628, but the new series is very hard to unlock IMEI number is 520018-61-379938-9-05, Program version is 9901131158 & CXC125056 Hardware revision is: 99W15 KRC 114 278/40 R2E This type oh phone is year 1999 Problem: When I start erserv 1.7 and check any command (not sp-unlock this tampered the pohone checked) the prog says 'Failed to enter sp mode' and the phon power up. I tray to use with zulea ericload prg says 'error port set' and ericflesh prog says ' time out ...' can you still help me Manfred

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
D900 Userlock & UFS Failed to enter TAT mode	aberiya	SWIFT Platform	0	03-06-2007 07:44
samsung e330 failed to enter TAT mode	celluniversal	SWIFT Platform	7	03-04-2007 18:39
failed to enter TAT mode!!!!	.:ramtelecom:.	UFS2 + UFS3-Tornadoflasher	4	02-19-2007 19:39
torch on innokia 1100 and failed to enter local mode	nellabe	Nokia Digital Core Technology 4 ( DCT-4 )	1	12-30-2006 09:53
Twister an E700 Failed to enter TAT mode	Flash0r	Twisterflasher	6	05-09-2005 23:23

05-15-1999, 17:14	#2 (permalink)
sc~micro Insane Poster Join Date: May 1999 Posts: 69 Member: 41 Status: Offline Thanks: 1 Thanked 5 Times in 2 Posts	I had the same problem once. Try new cable. Get schematics from 'mobile.8m.com'

05-15-1999, 17:44	#3 (permalink)
ptkrf Freak Poster Join Date: May 1999 Location: in my mind Age: 45 Posts: 301 Member: 17 Status: Offline Thanks: 2 Thanked 6 Times in 2 Posts	thanks, but still don't work Manfred

05-18-1999, 15:01	#4 (permalink)
Melorien Freak Poster Join Date: May 1999 Posts: 153 Member: 74 Status: Offline Thanks: 10 Thanked 62 Times in 17 Posts	Easy when you connect the phone and will enter the test mode you have to push the no buttom quick not hold it in 1 of a 10 pice of a sec. If not check pin 9 it must have the 5V. Dalton

05-18-1999, 17:26	#5 (permalink)
ptkrf Freak Poster Join Date: May 1999 Location: in my mind Age: 45 Posts: 301 Member: 17 Status: Offline Thanks: 2 Thanked 6 Times in 2 Posts	Hi guys, thanks but the problem is the phone! hardware interface and cable works great on older phones, even on phones manufactured in 99' but the IMEI number MUST be lower then 52**-61-***--, ERSERV 1.3 (1.7...) works great, if IMEI start on number 490*, here is what hapend when use erserv: Ericsson 6xx or 7xx detected Enter TEST Mode ... Failed to enter sp mode ... then the phone power up The only way for new phone to be accepted with erserv 1.3 or Zulea dos programs, must be TAMPERED, then the programs work fine !!!! Who now how to make the phone TAMPERED if not accepted with erserv 1.3 or Zulea dos programs ????? please help me.... thanks Manfred