V980 DEAD after RSA remove - GSM-Forum

sjakie · 09-02-2005, 13:37

Clip serial: ---------, version: 2.15, initializing... OK
Searching for phone... found S Flash Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 6.12
Phone may need "Remove RSA" procedure to get unlocked with Smart-Clip button, check model list at "Unlock" tab
Reading bus width... OK
Reading flash id... Micron-MT28F1284W18BET (x2)
Phone group: C975,C980,V980
Hardware IMEI: 355603000248239
Security area saved to "S Flash Rainbow POG 355603000248239.pds"
Writing section0 done
Turning phone off... OK
Searching for phone... no phone found
Searching for phone... clip communication failed

After reqeust too remove batterie, phone cannot communicate with prog.
Also cannot enter in manual flashmode,

What should i do ?

Regards
Sjakie

megone · 09-02-2005, 13:44

when try to put in flash mode...manual what say your phone??
error 0e????

sjakie · 09-02-2005, 13:56

Hi, it says nothing.
Simply dead.

regards
Sjakie

megone · 09-02-2005, 14:00

bad.....situation...i think you must contact smart clip team...must have some solution for this
b.r.

Obeone13 · 09-02-2005, 14:11

I ever have this problem Don't worry
Just put * # and power on for test mode and then use samart-clip connect phone and go to unlock page and then don't click connect to test mode on Sw click unlock RSA again after that phone will alive

BR
Obeone

sjakie · 09-02-2005, 14:29

Quote:

Originally Posted by Obeone13

I ever have this problem Don't worry
Just put * # and power on for test mode and then use samart-clip connect phone and go to unlock page and then don't click connect to test mode on Sw click unlock RSA again after that phone will alive

BR
Obeone

Hi, as stated earlier i cannot put in testmode

regards
Sjakie

TATO GSM · 09-02-2005, 14:37

Quote:

Originally Posted by Obeone13

I ever have this problem Don't worry
Just put * # and power on for test mode and then use samart-clip connect phone and go to unlock page and then don't click connect to test mode on Sw click unlock RSA again after that phone will alive

BR
Obeone

This talk he certain and the dissolution is tester more than his bitter
Thanks to you

sjakie · 09-02-2005, 14:54

Hi, i was mistaken.
although nothing on screen, i can connect in to flashmode
on smart-moto, but how too repair.
Wrote back Security area, but phone still dead.

Regards
Sjakie

Searching for phone... found S Flash Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 5.F1
Reading bus width... OK
Reading flash id... Micron-MT28F1284W18BET (x2)
Phone group: C975,C980,V980
Hardware IMEI: 355603000248239
Security area saved to "S Flash Rainbow POG 355603000248239 (2).pds"
This phone does not need "Remove RSA" procedure, you may unlock it with Smart-Clip button
Writing security area... done
Turning phone off... OK

sjakie · 09-02-2005, 22:39

Hi, im using smart-clip.
Maybe im in wrong forum ?

regards
Sjakie

PS phone still dead after full flash downloaded from support

hitibiti · 09-02-2005, 22:42

are you sure about batrey is full ? cose i was done many moto V980 no one is dead
try to charge battey and enterphone in test mode and repeat step

evilgabbie · 02-02-2006, 19:09

anyone have c980 flash ?? not found on bootloader

GSM Brothers · 02-03-2006, 09:14

contact me , i have flash

seth_ro · 02-03-2006, 09:26

put it in flash-mode
perform PDS repair
fullflash the phone
works 100%
happened to me many times, seems SC doesn't like V980 all that much

mobilis · 02-13-2006, 15:14

pls help me get full flas hor v980 for PST *.shx flash

09-02-2005, 13:37	#1 (permalink)
sjakie No Life Poster Join Date: Dec 1999 Location: NL Age: 44 Posts: 1,350 Member: 847 Status: Offline Thanks: 30 Thanked 32 Times in 27 Posts	V980 DEAD after RSA remove Clip serial: ---------, version: 2.15, initializing... OK Searching for phone... found S Flash Rainbow POG, getting test interface... interface not found Switching to flash mode... OK Reading phone boot version... 6.12 Phone may need "Remove RSA" procedure to get unlocked with Smart-Clip button, check model list at "Unlock" tab Reading bus width... OK Reading flash id... Micron-MT28F1284W18BET (x2) Phone group: C975,C980,V980 Hardware IMEI: 355603000248239 Security area saved to "S Flash Rainbow POG 355603000248239.pds" Writing section0 done Turning phone off... OK Searching for phone... no phone found Searching for phone... clip communication failed After reqeust too remove batterie, phone cannot communicate with prog. Also cannot enter in manual flashmode, What should i do ? Regards Sjakie

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
P910i dead after RSA remove, plz help	adi2002	Sony Ericsson	7	09-25-2007 11:20
P910 Dead after RSA Removal..Plz Help!	Nokia man	Sony Ericsson	49	11-23-2006 13:49
2 V3s dead after RSA removal	jaxhasu	Smart-Clip	5	11-12-2006 18:48
v3 razor dead after rsa remove by smart clip	shabeer	Motorola Hardware Repair Section	4	12-17-2005 16:38
T630 dead after RSA remove	xelo	Sony Ericsson	14	10-07-2004 14:41

09-02-2005, 13:44	#2 (permalink)
megone No Life Poster Join Date: Jun 2003 Location: Lichtenstain Age: 36 Posts: 1,187 Member: 31594 Status: Offline Thanks: 1 Thanked 13 Times in 7 Posts	when try to put in flash mode...manual what say your phone?? error 0e????

09-02-2005, 13:56	#3 (permalink)
sjakie No Life Poster Join Date: Dec 1999 Location: NL Age: 44 Posts: 1,350 Member: 847 Status: Offline Thanks: 30 Thanked 32 Times in 27 Posts	Hi, it says nothing. Simply dead. regards Sjakie

09-02-2005, 14:00	#4 (permalink)
megone No Life Poster Join Date: Jun 2003 Location: Lichtenstain Age: 36 Posts: 1,187 Member: 31594 Status: Offline Thanks: 1 Thanked 13 Times in 7 Posts	bad.....situation...i think you must contact smart clip team...must have some solution for this b.r.

09-02-2005, 14:11	#5 (permalink)
Obeone13 Freak Poster Join Date: Apr 2005 Location: Place One Age: 38 Posts: 322 Member: 132758 Status: Online Thanks: 20 Thanked 17 Times in 13 Posts	I ever have this problem Don't worry Just put * # and power on for test mode and then use samart-clip connect phone and go to unlock page and then don't click connect to test mode on Sw click unlock RSA again after that phone will alive BR Obeone

09-02-2005, 14:54	#8 (permalink)
sjakie No Life Poster Join Date: Dec 1999 Location: NL Age: 44 Posts: 1,350 Member: 847 Status: Offline Thanks: 30 Thanked 32 Times in 27 Posts	Hi, i was mistaken. although nothing on screen, i can connect in to flashmode on smart-moto, but how too repair. Wrote back Security area, but phone still dead. Regards Sjakie Searching for phone... found S Flash Rainbow POG, getting test interface... interface not found Switching to flash mode... OK Reading phone boot version... 5.F1 Reading bus width... OK Reading flash id... Micron-MT28F1284W18BET (x2) Phone group: C975,C980,V980 Hardware IMEI: 355603000248239 Security area saved to "S Flash Rainbow POG 355603000248239 (2).pds" This phone does not need "Remove RSA" procedure, you may unlock it with Smart-Clip button Writing security area... done Turning phone off... OK

09-02-2005, 22:39	#9 (permalink)
sjakie No Life Poster Join Date: Dec 1999 Location: NL Age: 44 Posts: 1,350 Member: 847 Status: Offline Thanks: 30 Thanked 32 Times in 27 Posts	Hi, im using smart-clip. Maybe im in wrong forum ? regards Sjakie PS phone still dead after full flash downloaded from support

09-02-2005, 22:42	#10 (permalink)
hitibiti No Life Poster Join Date: Mar 2003 Location: Micro-Box in Tunisia Age: 33 Posts: 7,384 Member: 24023 Status: Offline Sonork: 100.61317 Thanks: 128 Thanked 2,499 Times in 485 Posts	are you sure about batrey is full ? cose i was done many moto V980 no one is dead try to charge battey and enterphone in test mode and repeat step

02-02-2006, 19:09	#11 (permalink)
evilgabbie Freak Poster Join Date: Sep 2004 Location: Toronto Age: 30 Posts: 162 Member: 84323 Status: Offline Thanks: 6 Thanked 7 Times in 6 Posts	anyone have c980 flash ?? not found on bootloader

02-03-2006, 09:14	#12 (permalink)
GSM Brothers No Life Poster Join Date: Sep 2000 Location: Romania,Cluj Age: 39 Posts: 1,161 Member: 2203 Status: Offline Thanks: 157 Thanked 47 Times in 41 Posts	contact me , i have flash

02-03-2006, 09:26	#13 (permalink)
seth_ro Freak Poster Join Date: Oct 2005 Location: Romania Age: 31 Posts: 484 Member: 188359 Status: Offline Thanks: 0 Thanked 9 Times in 8 Posts	put it in flash-mode perform PDS repair fullflash the phone works 100% happened to me many times, seems SC doesn't like V980 all that much

02-13-2006, 15:14	#14 (permalink)
mobilis Freak Poster Join Date: Jan 2002 Location: cmr Age: 46 Posts: 258 Member: 8970 Status: Offline Thanks: 8 Thanked 3 Times in 3 Posts	pls help me get full flas hor v980 for PST *.shx flash