BIG PROBLEM with UNIBOX! OUTPUT power at line 1 is too low..

[Handycracker2k2]

hello!

a few days ago i have tried to write some IMEI RPL files in my phone!

MCU Nokia Version: 1.122, and up to date.
SMCU Nokia Version: 1.4, and up to date.
Please connect power supply next to the USB connector on the box and make sure, that the power supply provides at least 6,00 Volts!
Terminated with error: Input power 4,41V too low, at least 6,00V needed [00000C02]. 00011204. 0000040D. 00000101. 0000020C. 0001023A. 000110D0. 0001115A. 00011148

then i connect a 9V DC connector, and tried again:

MCU Nokia Version: 1.122, and up to date.
SMCU Nokia Version: 1.4, and up to date.
Input power: 10,36V OK.
Hardware ID: 0120
Boot Loader: u_2nd.fia 2 kB
Version: 4.49.0

and everything was OK!...

but today, i want to flash some phone, i get this strange error:

MCU Nokia Version: 1.122, and up to date.
SMCU Nokia Version: 1.4, and up to date.
Terminated with error: No power connected, at least 4,50V needed [00000C03]. 00011204. 0000040D. 00000101. 0000020C. 0001023A. 000110D0. 00011140. 00011510

very funny, because without power box won´t work

i thought this was an stupid error, and tried again with a new error:

MCU Nokia Version: 1.122, and up to date.
SMCU Nokia Version: 1.4, and up to date.
Initializing phone...
Terminated with error: Output power at Line1 0,04V out of range of: 4,00V ±10,0% [00000C14]. 0001581C. 00011824

and this comes every time i tried to read or flash something! sometimes wit 0,02V, 0,04V and 0.08V! it´s the same if i connect the 9V supply!

and now i can´t do anything!

is this Hardware damage? any chance to repair this??

i need my box

BR hk2k2

[Handycracker2k2]

hmm, now i have tried again, and now i have the same problem like other users, DEVICE OPEN FAILED AT USB...


strange box

i think they are some hardware problems inside, maybe the PIC or ATMEGA?

any change to fix this problems myself?

like UFS repair tools

br hk2k2

[xileen2k]

this had happen to me too... I jusyt changed PC and now it works again...


May I suggest you plug only 4.5V DC to power beside USB plug to augment the voltage requirements of the box....


This i must say a hungry box.....


WBR,

[universalbox]

Originally Posted by Handycracker2k2

hello!

a few days ago i have tried to write some IMEI RPL files in my phone!





then i connect a 9V DC connector, and tried again:




and everything was OK!...

but today, i want to flash some phone, i get this strange error:



very funny, because without power box won´t work

i thought this was an stupid error, and tried again with a new error:


and this comes every time i tried to read or flash something! sometimes wit 0,02V, 0,04V and 0.08V! it´s the same if i connect the 9V supply!

and now i can´t do anything!

is this Hardware damage? any chance to repair this??

i need my box

BR hk2k2

This is power problem is a hw failure of the box in most cases. The RPL writing needs at least 6V thats why it asked you for more power, but the later messages are definetly hw problem.

[Handycracker2k2]

what should i do now? sending back to my reseller??



i´ve readed something about NEVER REMOVE THE BATTERY!

i´ve measured the battery, it is total empty!! maybe this is the fault??

very bad, because u have to change box all 2-3 months, depending on battery lifetime

BR hk2k2

[universalbox]

Originally Posted by Handycracker2k2

what should i do now? sending back to my reseller??
i´ve readed something about NEVER REMOVE THE BATTERY!
i´ve measured the battery, it is total empty!! maybe this is the fault??
very bad, because u have to change box all 2-3 months, depending on battery lifetime
BR hk2k2

Yes, that battery can cause this problem. If that is empty that means dallas forgot everything. In this case you will need a new box. I am very sorry.