K608i unlocked ok and then no power... - GSM-Forum

Burnt Cobba · 12-10-2005, 13:51

hi all

tried this K608i with CID 49. used test point (had some trouble to make test point since it was surrounded with epoxy glue). It was shown that phone colour was RED. (in fact this is silver from 3).. anyway.....

Once cleared the locks , it was asked to repower again... phone then was detected as CID 16. and then test mode was disengaged (according to the log)

Tried to power it up and no power.

Tried to communicate again with phone it reacts ok but stops when sending boot loader.

Is this a hardware or software problem pls? need some guidance asap pls.

thanks for any help
al

Amir-SkillZ · 12-10-2005, 13:58

Try Again Changing CID color to RED and Then Unlock If still not...
Flash with k600 flash ........Hope It Works

essojay · 12-10-2005, 19:06

Quote:

Originally Posted by Burnt Cobba

hi all

tried this K608i with CID 49. used test point (had some trouble to make test point since it was surrounded with epoxy glue). It was shown that phone colour was RED. (in fact this is silver from 3).. anyway.....

Once cleared the locks , it was asked to repower again... phone then was detected as CID 16. and then test mode was disengaged (according to the log)

Tried to power it up and no power.

Tried to communicate again with phone it reacts ok but stops when sending boot loader.

Is this a hardware or software problem pls? need some guidance asap pls.

thanks for any help
al

you ve tampered the testpoint area i guess ... you need to check the resistor very well or remove it completely and joint the point directly..

bR

Burnt Cobba · 12-11-2005, 15:16

can i remove resistor compeltely and instead short the 2 points directly?

i dont know the value of the resistor also

i had problems since the area was imersed in epoxy glue.

thanks for the help
al

Zaihtam · 12-12-2005, 11:45

you just need to short the TP to the ground only, after the phone is detected you must disconnect the TP.

essojay · 12-12-2005, 13:33

Quote:

Originally Posted by Burnt Cobba

can i remove resistor compeltely and instead short the 2 points directly?

i dont know the value of the resistor also

i had problems since the area was imersed in epoxy glue.

thanks for the help
al

yes, you can do that,...

bR

Burnt Cobba · 12-15-2005, 09:54

problem solved phewww

as essojay suggested the resistor part had dislodged slightly from the track. had to connect the track and solder it back to the resistor section. If anyone has such a problem just plug in the charger. If the red light does not show up then the track has been damaged.

thanks essojay
al

12-10-2005, 13:51	#1 (permalink)
Burnt Cobba No Life Poster Join Date: Apr 2002 Location: The Green Mile Posts: 3,653 Member: 11325 Status: Offline Thanks Meter: 266	K608i unlocked ok and then no power... hi all tried this K608i with CID 49. used test point (had some trouble to make test point since it was surrounded with epoxy glue). It was shown that phone colour was RED. (in fact this is silver from 3).. anyway..... Once cleared the locks , it was asked to repower again... phone then was detected as CID 16. and then test mode was disengaged (according to the log) Tried to power it up and no power. Tried to communicate again with phone it reacts ok but stops when sending boot loader. Is this a hardware or software problem pls? need some guidance asap pls. thanks for any help al

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
T11 fomat ok...full flash ok..but still no power..	rolly_van	Infinity-Box	3	10-29-2008 11:08
K608i flashed and now no power...	Burnt Cobba	Universalbox	1	08-04-2006 16:35
S710a after flashing then no power	deepcook_dalat	Cruiser Suite	7	01-05-2006 16:20
t610 hang then no power	eureka8888	Sony Ericsson	4	09-28-2003 14:42

12-10-2005, 13:58	#2 (permalink)
Amir-SkillZ No Life Poster Join Date: Nov 2004 Location: Capetown Posts: 6,709 Member: 91045 Status: Offline Thanks Meter: 8,696	Try Again Changing CID color to RED and Then Unlock If still not... Flash with k600 flash ........Hope It Works

12-11-2005, 15:16	#4 (permalink)
Burnt Cobba No Life Poster Join Date: Apr 2002 Location: The Green Mile Posts: 3,653 Member: 11325 Status: Offline Thanks Meter: 266	can i remove resistor compeltely and instead short the 2 points directly? i dont know the value of the resistor also i had problems since the area was imersed in epoxy glue. thanks for the help al

12-12-2005, 11:45	#5 (permalink)
Zaihtam No Life Poster Join Date: Dec 2004 Location: 0x001FD00 Posts: 1,285 Member: 98572 Status: Offline Thanks Meter: 36	you just need to short the TP to the ground only, after the phone is detected you must disconnect the TP.

12-15-2005, 09:54	#7 (permalink)
Burnt Cobba No Life Poster Join Date: Apr 2002 Location: The Green Mile Posts: 3,653 Member: 11325 Status: Offline Thanks Meter: 266	problem solved phewww as essojay suggested the resistor part had dislodged slightly from the track. had to connect the track and solder it back to the resistor section. If anyone has such a problem just plug in the charger. If the red light does not show up then the track has been damaged. thanks essojay al