nokia 1200 Contents Package Extracting Failed: Process Failed, Repowering Mobile - GSM-Forum

romey_singh2 · 02-19-2010, 08:28

1st Boot: Ok, DCT4, UPP: 2292 [Rh-99] [2.0.9.0]
2nd Boot: u3_2nd.fia, Ver: 4.79.0
Fl0: 0x01000000-0x013FFFFF,00208828,St M58MR032
Algorithm: u3_st_i.fia, Ver: 4.79.0
Algorithm Ok, MSID: 84167EAE3D758EDBC7F2EF394C
Decoded MSID: 3E4EBAE9-00110FA3-A8000000
Encoded FAID: 77688210-0C69F39F-8BFE0B0B
IMAGE: rh99_05.230
Area1: 0x01000000-0x0100FFFF Erased, Time: 00:01
Area2: 0x01010000-0x013AFFFF Erased, Time: 01:05
Area3: 0x013B0000-0x013EFFFF Erased, Time: 00:05
Area4: 0x017C0000-0x017EFFFF Out of Chip Bounds
Area5: 0x01FC0000-0x01FEFFFF Out of Chip Bounds
MCU Flashing Completed, Time: 00:13
IMAGE: rh990_nai5.23mg
Area1: 0x01380000-0x013AFFFF Erased, Time: 00:03
CNT Flashing Completed, Time: 00:00
Extracting Contents Package ...
Init Local Mode Failed
Contents Package Extracting Failed:
Process Failed, Repowering Mobile

Ramzan khan · 02-19-2010, 08:43

earse full flash and then again write full flash.write pm.full factory set.if still problem then check hardware

farihabest · 02-19-2010, 08:50

its because of not goto to local mode for writing PPM file. So flash with UB and all will be okey.

OR

Erase.
Flash with latest version
then pm and ui settings

metals · 02-19-2010, 16:56

no need c**lone just fallow as above means just erease full then flash ui after write pm full factory setting every thing become ok don't care about version anyway 5.23 is the best

khalidjan · 02-19-2010, 18:38

just drop the down point. I mean the last point should not be touched with cable. Put some thing on the last point, flash it & post result.

iets · 02-21-2010, 10:28

entering into local mode/test mode is BSI path fault. check ur cable inside BSI resister( should be 5.1k).or press & hold pwr button of mobile whn msg appears entering local mode.

chk & post result.

sajohaker · 02-21-2010, 10:36

downgrade use old version and flash phone .....phost rezult.......

software zone · 02-21-2010, 11:26

use easy cable.100/100% tested even you can flash unlock with any device with out problem

shiburock · 02-21-2010, 16:28

Quote:

Originally Posted by romey_singh2

1st boot: Ok, dct4, upp: 2292 [rh-99] [2.0.9.0]
2nd boot: U3_2nd.fia, ver: 4.79.0
fl0: 0x01000000-0x013fffff,00208828,st m58mr032
algorithm: U3_st_i.fia, ver: 4.79.0
algorithm ok, msid: 84167eae3d758edbc7f2ef394c
decoded msid: 3e4ebae9-00110fa3-a8000000
encoded faid: 77688210-0c69f39f-8bfe0b0b
image: Rh99_05.230
area1: 0x01000000-0x0100ffff erased, time: 00:01
area2: 0x01010000-0x013affff erased, time: 01:05
area3: 0x013b0000-0x013effff erased, time: 00:05
area4: 0x017c0000-0x017effff out of chip bounds
area5: 0x01fc0000-0x01feffff out of chip bounds
mcu flashing completed, time: 00:13
image: Rh990_nai5.23mg
area1: 0x01380000-0x013affff erased, time: 00:03
cnt flashing completed, time: 00:00
extracting contents package ...
Init local mode failed
contents package extracting failed:
Process failed, repowering mobile

use only easy cable then flash your phone
10000000000000000% your problem solved

br,

shibu rock

SMLATLAS · 02-22-2010, 22:56

then full flash, 100% ok, tested by me.

shanryzen · 02-23-2010, 05:23

if you use all of this ways that they gave 100% cpu problem

StRaNgE PeRsOn · 02-23-2010, 14:57

try only MCU and CNT then flash PpM seperately

post results

StRaNgE PeRsOn · 02-23-2010, 14:58

If no luck then try to flash with latest version

-=Meltech09=- · 05-19-2010, 08:51

Quote:

Originally Posted by romey_singh2

1st Boot: Ok, DCT4, UPP: 2292 [Rh-99] [2.0.9.0]
2nd Boot: u3_2nd.fia, Ver: 4.79.0
Fl0: 0x01000000-0x013FFFFF,00208828,St M58MR032
Algorithm: u3_st_i.fia, Ver: 4.79.0
Algorithm Ok, MSID: 84167EAE3D758EDBC7F2EF394C
Decoded MSID: 3E4EBAE9-00110FA3-A8000000
Encoded FAID: 77688210-0C69F39F-8BFE0B0B
IMAGE: rh99_05.230
Area1: 0x01000000-0x0100FFFF Erased, Time: 00:01
Area2: 0x01010000-0x013AFFFF Erased, Time: 01:05
Area3: 0x013B0000-0x013EFFFF Erased, Time: 00:05
Area4: 0x017C0000-0x017EFFFF Out of Chip Bounds
Area5: 0x01FC0000-0x01FEFFFF Out of Chip Bounds
MCU Flashing Completed, Time: 00:13
IMAGE: rh990_nai5.23mg
Area1: 0x01380000-0x013AFFFF Erased, Time: 00:03
CNT Flashing Completed, Time: 00:00
Extracting Contents Package ...
Init Local Mode Failed
Contents Package Extracting Failed:
Process Failed, Repowering Mobile

here is your 100% solution..

just follow this trick...

then fullflash it again

bigmarsa · 05-20-2010, 11:58

use easy cable u r problem will be solve . tested 100% . after flash post result.

02-19-2010, 08:28	#1 (permalink)
romey_singh2 No Life Poster Join Date: Apr 2009 Location: India Posts: 885 Member: 1014826 Status: Offline Thanks Meter: 88	nokia 1200 Contents Package Extracting Failed: Process Failed, Repowering Mobile 1st Boot: Ok, DCT4, UPP: 2292 [Rh-99] [2.0.9.0] 2nd Boot: u3_2nd.fia, Ver: 4.79.0 Fl0: 0x01000000-0x013FFFFF,00208828,St M58MR032 Algorithm: u3_st_i.fia, Ver: 4.79.0 Algorithm Ok, MSID: 84167EAE3D758EDBC7F2EF394C Decoded MSID: 3E4EBAE9-00110FA3-A8000000 Encoded FAID: 77688210-0C69F39F-8BFE0B0B IMAGE: rh99_05.230 Area1: 0x01000000-0x0100FFFF Erased, Time: 00:01 Area2: 0x01010000-0x013AFFFF Erased, Time: 01:05 Area3: 0x013B0000-0x013EFFFF Erased, Time: 00:05 Area4: 0x017C0000-0x017EFFFF Out of Chip Bounds Area5: 0x01FC0000-0x01FEFFFF Out of Chip Bounds MCU Flashing Completed, Time: 00:13 IMAGE: rh990_nai5.23mg Area1: 0x01380000-0x013AFFFF Erased, Time: 00:03 CNT Flashing Completed, Time: 00:00 Extracting Contents Package ... Init Local Mode Failed Contents Package Extracting Failed: Process Failed, Repowering Mobile

02-21-2010, 10:28	#6 (permalink)
iets Junior Member Join Date: Feb 2009 Location: hyderabad,India Posts: 12 Member: 981175 Status: Offline Thanks Meter: 3	nokia 1200 Contents Package Extracting Failed: Process Failed, Repowering Mobile entering into local mode/test mode is BSI path fault. check ur cable inside BSI resister( should be 5.1k).or press & hold pwr button of mobile whn msg appears entering local mode. chk & post result.

02-22-2010, 22:56	#10 (permalink)
SMLATLAS Crazy Poster Join Date: Jan 2008 Location: Algeria Posts: 50 Member: 687988 Status: Offline Thanks Meter: 11	do ERASE first; then full flash, 100% ok, tested by me.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
1200 Contents Package Extracting Failed	sr8787	Nokia Hardware & Hardware Repair	8	09-28-2010 13:10
1200 Contents Package Extracting Failed	sr8787	Nokia Hardware & Hardware Repair	10	08-25-2009 03:23
1200 Contents Package Extracting Failed	sr8787	Nokia Hardware & Hardware Repair	1	08-20-2009 09:23

02-19-2010, 08:43	#2 (permalink)
Ramzan khan No Life Poster Join Date: Dec 2006 Posts: 522 Member: 405696 Status: Offline Thanks Meter: 148	earse full flash and then again write full flash.write pm.full factory set.if still problem then check hardware

02-19-2010, 08:50	#3 (permalink)
farihabest No Life Poster Join Date: Oct 2007 Location: MX-Key and me ...The Best Posts: 798 Member: 617692 Status: Offline Thanks Meter: 306	its because of not goto to local mode for writing PPM file. So flash with UB and all will be okey. OR Erase. Flash with latest version then pm and ui settings

02-19-2010, 16:56	#4 (permalink)
metals No Life Poster Join Date: Jul 2008 Posts: 1,010 Member: 811779 Status: Offline Thanks Meter: 242	no need c**lone just fallow as above means just erease full then flash ui after write pm full factory setting every thing become ok don't care about version anyway 5.23 is the best

02-19-2010, 18:38	#5 (permalink)
khalidjan No Life Poster Join Date: Nov 2007 Location: United State Of Islam Age: 34 Posts: 2,054 Member: 624551 Status: Offline Sonork: 100.1584837 Thanks Meter: 737	just drop the down point. I mean the last point should not be touched with cable. Put some thing on the last point, flash it & post result.

02-21-2010, 10:36	#7 (permalink)
sajohaker No Life Poster Join Date: Feb 2008 Location: Bosnia Posts: 865 Member: 698071 Status: Offline Sonork: 100.1622915 Thanks Meter: 283	downgrade use old version and flash phone .....phost rezult.......

02-21-2010, 11:26	#8 (permalink)
software zone No Life Poster Join Date: Apr 2007 Location: nothing Posts: 1,543 Member: 494167 Status: Offline Thanks Meter: 292	use easy cable.100/100% tested even you can flash unlock with any device with out problem

02-23-2010, 05:23	#11 (permalink)
shanryzen Cheater -Don't Deal with him- Join Date: Apr 2008 Location: California USA Posts: 679 Member: 743601 Status: Offline Sonork: 83392409 Thanks Meter: 138	if you use all of this ways that they gave 100% cpu problem

02-23-2010, 14:57	#12 (permalink)
StRaNgE PeRsOn No Life Poster Join Date: Nov 2006 Location: PAKISTAN Posts: 3,169 Member: 391445 Status: Offline Sonork: 100.1583575 Thanks Meter: 392	try only MCU and CNT then flash PpM seperately post results

02-23-2010, 14:58	#13 (permalink)
StRaNgE PeRsOn No Life Poster Join Date: Nov 2006 Location: PAKISTAN Posts: 3,169 Member: 391445 Status: Offline Sonork: 100.1583575 Thanks Meter: 392	If no luck then try to flash with latest version

05-20-2010, 11:58	#15 (permalink)
bigmarsa No Life Poster Join Date: Nov 2008 Location: india Age: 49 Posts: 599 Member: 901335 Status: Offline Sonork: 100.1652281 Thanks Meter: 151	use easy cable u r problem will be solve . tested 100% . after flash post result.