nokia 1200 dead by flashing - GSM-Forum

jitugrover · 11-26-2008, 04:27

nokia 1200 handset was restarting i flash with hwk ufs-3.. and handset is dead now . plz give n e solution
log is here:\
1st Boot: Ok, DCT4, UPP: 2292 [Rh-99] [2.0.8.0]
2nd Boot: u3_2nd.fia, Ver: 4.76.0
Fl0: 0x01000000-0x013FFFFF,00898872,Int 28F320W18
Algorithm: u3_intel.fia, Ver: 4.76.0
Algorithm Ok, MSID: 84B439045D5FCE84D203534122
Decoded MSID: 3E4EBAE9-00421234-AA000000
Encoded FAID: 1721DF1F-0FE2504D-50DCD533
IMAGE: rh99_03.440
Area1: 0x01000000-0x0100FFFF Erased, Time: 00:00
Area2: 0x01010000-0x013BFFFF Erased, Time: 00:36
Area3: 0x013C0000-0x013EFFFF Erased, Time: 00:01
Area4: 0x017C0000-0x017EFFFF Out of Chip Bounds
Area5: 0x01FC0000-0x01FEFFFF Out of Chip Bounds
MCU Flashing Completed, Time: 00:20
IMAGE: rh990_nai3.44mg
Area1: 0x01380000-0x013BFFFF Erased, Time: 00:02
CNT Flashing Completed, Time: 00:01
Extracting Contents Package ...
Init Local Mode Failed
Contents Package Extracting Failed:
Process Failed, Repowering Mobile

my toh · 11-26-2008, 04:57

Are your phone water damage?

try rehot uem and cpu, then try again!

xerraco · 11-26-2008, 05:51

Reheat Flash IC then reflash.

amol_sm · 11-26-2008, 06:09

When this message show Extracting Contents Package ...
Try to power on the set manually.

Post result.

dongspi · 11-26-2008, 06:15

hi!

did you try to flash the unit to jaf?
if not try first..

nhoy'sbarage · 11-26-2008, 06:21

Quote:

Originally Posted by jitugrover

Extracting Contents Package ...
Init Local Mode Failed
Contents Package Extracting Failed:
Process Failed, Repowering Mobile

meaning.... the phone did not boot into local mode!..

after flashing the phone must show "local mode" if it doesn't?...

upp fault..

reflow.., rebol.., or replace....!

Odia The Ultimate · 11-26-2008, 07:48

Quote:

Originally Posted by nhoy'sbarage

meaning.... the phone did not boot into local mode!..

after flashing the phone must show "local mode" if it doesn't?...

upp fault..

reflow.., rebol.., or replace....!

or simply bad cable.

Odia.

MOURAD™ · 11-26-2008, 08:41

1- remove conedsators Behind conector battery.

2- clean it

2- full erase.

4- full flash.

or can skip erase from area replace 9 by 1

...............good......................

venuno · 11-26-2008, 08:51

erase flash then flash it again using jaf or hwk
after flash write pm unlock thats it...

AZZ14 · 11-27-2008, 15:38

bad cable like says odia or chage other mcu if its made in india use india packs

11-26-2008, 04:27	#1 (permalink)
jitugrover Freak Poster Join Date: Nov 2006 Posts: 472 Member: 392151 Status: Offline Thanks Meter: 80	nokia 1200 dead by flashing nokia 1200 handset was restarting i flash with hwk ufs-3.. and handset is dead now . plz give n e solution log is here:\ 1st Boot: Ok, DCT4, UPP: 2292 [Rh-99] [2.0.8.0] 2nd Boot: u3_2nd.fia, Ver: 4.76.0 Fl0: 0x01000000-0x013FFFFF,00898872,Int 28F320W18 Algorithm: u3_intel.fia, Ver: 4.76.0 Algorithm Ok, MSID: 84B439045D5FCE84D203534122 Decoded MSID: 3E4EBAE9-00421234-AA000000 Encoded FAID: 1721DF1F-0FE2504D-50DCD533 IMAGE: rh99_03.440 Area1: 0x01000000-0x0100FFFF Erased, Time: 00:00 Area2: 0x01010000-0x013BFFFF Erased, Time: 00:36 Area3: 0x013C0000-0x013EFFFF Erased, Time: 00:01 Area4: 0x017C0000-0x017EFFFF Out of Chip Bounds Area5: 0x01FC0000-0x01FEFFFF Out of Chip Bounds MCU Flashing Completed, Time: 00:20 IMAGE: rh990_nai3.44mg Area1: 0x01380000-0x013BFFFF Erased, Time: 00:02 CNT Flashing Completed, Time: 00:01 Extracting Contents Package ... Init Local Mode Failed Contents Package Extracting Failed: Process Failed, Repowering Mobile

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Nokia 1200 Dead	..::Rizwan::..	Nokia Hardware & Hardware Repair	9	08-10-2014 19:35
1200 Dead by Cyclone Help Please....	Sydney_Unlocker	Cyclonebox	16	05-21-2009 15:00
nokia 1200 dead in battey , in sw"insert sim card"	ameerali19	Nokia Hardware & Hardware Repair	4	01-26-2009 12:09
nokia 1200 dead	noman shakir	Nokia Digital Core Technology 4 ( DCT-4 )	2	01-17-2009 09:47

11-26-2008, 04:57	#2 (permalink)
my toh Freak Poster Join Date: Sep 2005 Location: penang Posts: 163 Member: 183739 Status: Offline Thanks Meter: 11	Are your phone water damage? try rehot uem and cpu, then try again!

11-26-2008, 05:51	#3 (permalink)
xerraco No Life Poster Join Date: Nov 2008 Location: RVIII Posts: 11,696 Member: 890926 Status: Offline Thanks Meter: 2,053	Reheat Flash IC then reflash.

11-26-2008, 06:09	#4 (permalink)
amol_sm No Life Poster Join Date: Sep 2006 Posts: 2,929 Member: 343326 Status: Offline Thanks Meter: 1,463	When this message show Extracting Contents Package ... Try to power on the set manually. Post result.

11-26-2008, 06:15	#5 (permalink)
dongspi Junior Member Join Date: Aug 2007 Posts: 33 Member: 564294 Status: Offline Thanks Meter: 18	hi! did you try to flash the unit to jaf? if not try first..

11-26-2008, 08:41	#8 (permalink)
MOURAD™ No Life Poster Join Date: Mar 2007 Location: Guangzhou-China Posts: 1,289 Member: 468587 Status: Offline Sonork: 100.1612429 Thanks Meter: 681	1- remove conedsators Behind conector battery. 2- clean it 2- full erase. 4- full flash. or can skip erase from area replace 9 by 1 ...............good......................

11-26-2008, 08:51	#9 (permalink)
venuno No Life Poster Join Date: Jun 2007 Location: Talk to * and He Will Listen Posts: 3,820 Member: 532761 Status: Offline** Sonork: 100-1592994 Thanks Meter: 1,104	erase flash then flash it again using jaf or hwk after flash write pm unlock thats it...

11-27-2008, 15:38	#10 (permalink)
AZZ14 Freak Poster Join Date: Jul 2007 Location: BATNA/ALGERIA Posts: 130 Member: 538022 Status: Offline Thanks Meter: 93	bad cable like says odia or chage other mcu if its made in india use india packs