UFSx+HWK Release 28/10/2013 - Discussion - GSM-Forum

GsmMunna · 10-28-2013, 05:11

Release 28/10/2013

WARNING !!!
If the HWK is a "TRIAL" or affected by 3rd party tools, this software may not work properly, so use at your own risk.

You need to uninstall old HWK Setup Suite and HWK Support Suite and use the new UFSx Support Suite.

UFS_DCTxBB5 V 2.3.0.2
----------------------

1. BB5 RAPU Based Products USB Flashing / UI support added:
RM-884 (302)
2. DCT4 INFINEON Based Products Flashing / UI support added:
RM-908,RM-924,RM-925,RM-926,RM-928,RM-929,RM-961,RM-962
(105,210,.. 210,107,106)
3. Added HiBauds (up to 3Mbaud) on UFST Box, for Infineon
XG101 and XG110 Platforms.
4. DCT4 MTK Based Products UI support added:
RM-944,RM-945 (108)
5. Windows8 64bit support.

UFS_ATRz v2.3.0.2
------------------

1. Increased Baud Rate for J220,J230
2. Windows8 64bit support.

UFS_KZF v2.3.0.2
-----------------

1. Added Windows8 64 bit Support.

UFS_RTP v2.3.0.2
----------------

1. Added Windows8 64 bit Support.

SeDBx v2.3.0.2
--------------

1. Added Windows8 64 bit Support.

LG v 2.3.0.2
------------

1. Common: Windows8 64bit support.

SAMs V 2.3.0.2
--------------

SWIFT-AEROFONE
E1260B,E1260L added (PUNL,PIM,FL)
E1265,E2262 added (UNL,SECT,IM,FL)
INFINEON
C3322i,C3590,C3592 added (CUNL,PUNL,PIM,FL,UFL)

Many thanks to all those who have supported us!!!

Official SarasSoft Mirrors:-
http://forum.gsmhosting.com/vbb/f311...tions-1216246/

Odia The Ultimate · 10-28-2013, 11:27

Any download links supplied by users in this thread or sub-forum will be removed.

Please do not make any thanks posts in this thread, you can use the Thanks button for that.

Please do not post anything about why something has not been added or why some model has not been added, or they will be removed.

This thread is to discuss the 02.30.00.03 release, nothing else, installation issues should be posted in http://forum.gsmhosting.com/vbb/f311...oblems-822845/

Odia The Ultimate · 10-28-2013, 11:38

The latest release of the Panel software contains a new Backup and Restore Registry option, we urge our customers to use it.

1. Uninstall ALL previous versions, you MUST uninstall HWK Suite BEFORE trying to uninstall HWK Support Suite Setup.
2. Install UFSx Support Suite Setup
3. Connect your UFSx+HWK before running the UFSx Control Panel
4. Run UFSx Control Panel
5. Switch to the "Hardware" Tab
6. If you only have one UFSx connected it will be selected, if more than one, select the check box next to the required UFSx. You can click "Scan Boxes" to refresh the list if you have connected further boxes since opening the Control Panel
7. Click "Check Box"
8. Click "Update Box"
9. Click "Check Box" - Make sure "Box Status" = "True" or "Bad Software" and "Server Status" = "Support Ok", before proceeding
10. Switch to the "Software" Tab
11. Amend "Application Install Path" and/or "Nokia Install Path", if required.
12. Click "Check Server"
13. Click "Install"
14. If you have more than 1 UFSx+HWK run steps 5-13 for each UFSx+HWK (NOTE: You must install something at step 13)
15. Switch to the "Software" Tab
16. Click "Check Box" - Make sure "Box Status" = "True" and "Server Status" = "Support Ok", before proceeding
17. Click "Backup Registry" - Save this file on a removable media.

If you decide to re-install Windows, you can Install the setup suite, run the panel and click "Restore Registry", then "Check Box", this process should save you some install logs.

The registry backup can also be restored if you get some unexpected auth error when all was working fine before, this happens due to some registry cleaning software.

andre128 · 10-28-2013, 13:01

can't flash nokia 105

Quote:

CPU: GenuineIntel, Sp: 5
Platform: Windows NT 6.1 (Build 7601 Service Pack 1)
Versions: Ufs2xx.dll 3.2.4, Ufs2xx.sys 2.8.14
Current Paths:
EXE : C:\Program Files (x86)\Nokia\Phoenix
TESLA: C:\Wintesla\
DCT3 : C:\Program Files (x86)\Nokia\Phoenix\Flash3\
DCT4 : C:\Program Files (x86)\Nokia\Phoenix\Flash\
BB5 : C:\Program Files (x86)\Nokia\Phoenix\Flash\
UFxBoot V2.2 (c) SarasSoft 2003. Id: 62 CF 1 10
UFS_USB V2.8 (c) SarasSoft 2007. Sn: 13175
HID: 1A68273D00210039, HWK: A1.04-PRO1
Features: 00000001
Licence: True
LogFile: .\_!_LOG\13175_28137582_0_LOG.txt
If used non Auto-Ignition cable, press Power-On button
IF_SBL: XGOLD110, Ok
IF_EBL: Default_RAM_Bootloader 10.24, Mode: CC
BAUD_R: 921600
IFXFR_ERR_BAD_CMD
IFEBL_ERR_GSYS:
Process Failed, Repowering Mobile

ABUU YUUNUS · 10-30-2013, 18:31

Quote:

Originally Posted by andre128

can't flash nokia 105

Check for any liquid presence under the LCD. These kinds of mobile are prone to liquid attack due the torch facility that they enoy.

cpu486 · 10-31-2013, 09:58

So, if I want to upgrade from 2.3.0.1 to 2.3.0.2 I have to uninstall all and then install it again. It is not enough to just upgrade. Am I right or ...?

Nasir Mobiles · 10-31-2013, 11:49

Quote:

Originally Posted by andre128

can't flash nokia 105

how can you flash without flash files???

Odia The Ultimate · 10-31-2013, 12:59

Quote:

Originally Posted by cpu486

So, if I want to upgrade from 2.3.0.1 to 2.3.0.2 I have to uninstall all and then install it again. It is not enough to just upgrade. Am I right or ...?

Correct, but when you remove UFSx Support Suite none of the software modules will be remove, ONLY the support files, so when you run the panel it will update what was already installed via the panel before.

ABUU YUUNUS · 10-31-2013, 19:45

Dear Odia, I tried today to unlock two sony ericsson phones, T630 and T610 but without success. Each time I clicked on "GO" to get mobile booted, after a few incomplete info, software displays this error " invalid file name". As a result booting process is not completely done and phones couldn't be unlocked. Please what is the way out?

Odia The Ultimate · 10-31-2013, 22:47

Quote:

Originally Posted by ABUU YUUNUS

Dear Odia, I tried today to unlock two sony ericsson phones, T630 and T610 but without success. Each time I clicked on "GO" to get mobile booted, after a few incomplete info, software displays this error " invalid file name". As a result booting process is not completely done and phones couldn't be unlocked. Please what is the way out?

My local museum not have these relics, try RSA instead GO, if not helps I will need to refer to Saras.

ABUU YUUNUS · 11-01-2013, 11:02

Quote:

Originally Posted by Odia The Ultimate

My local museum not have these relics, try RSA instead GO, if not helps I will need to refer to Saras.

Thanks a lot Odia, I had tried using the RSA but the situation was the same. I think may be it has to do with the module and its files. Hoping to hear from your reply after contacting with Saras.

akhtar.abbas · 11-01-2013, 11:21

MCU SW : V 07.00 11-09-12 RM-647 (c) Nokia
PPM SW : V 07.00 11-09-12 RM-647 (c) Nokia IA
Platform: Infineon XG110
Prd.Code: 0592312
Bpr.Code: 0589577
Prod.Sn : 3E36681AI
HW Vers : 3001
UEM : 1328
UPP : 8850 [2292]
LCD Type: WIN:SERI:90 NT7542
IMEI : 358285-04-211272-7
SL Conf : 001-01-00000000000
SL Prof : 000000000003000-2
SL Var : 00003582850421127200
SL Aux : 000B0000
HW Sig : C763CCF910272051
Box Id : FFFFFFFFFFFFFFFF
BLK1= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN
BLK2= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN
BLK3= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN
BLK4= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN
BLK5= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN
BLK6= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN
BLK7= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN
Provider: GSM Test Equipment
UI Defaults Failed
Set UI Factory Defaults Failed
Set Full Factory Defaults Failed
Set Security Failed
-------------------------------------------fail sa like old version

Odia The Ultimate · 11-01-2013, 12:31

Quote:

Originally Posted by akhtar.abbas

UI Defaults Failed
Set UI Factory Defaults Failed
Set Full Factory Defaults Failed
Set Security Failed
-------------------------------------------fail sa like old version

Possible incorrect BSI resistance in cable, next to UI Settings is a combo box with local, test and normal, use this to check phone is switching mode correct.

Odia The Ultimate · 11-01-2013, 12:33

Quote:

Originally Posted by ABUU YUUNUS

Thanks a lot Odia, I had tried using the RSA but the situation was the same. I think may be it has to do with the module and its files. Hoping to hear from your reply after contacting with Saras.

Can you provide a screenshot?

akhtar.abbas · 11-01-2013, 12:47

Test mode set
Settings Full Factory Defaults...
Set OK!
Settings Software Upgrade Defaults...
Set OK!
Settings Service Centre Defaults...
Set OK!
Settings Production Tune Defaults...
Set OK!
Settings User Data Defaults...
Set OK!
Settings Leave Factory defaults...
Set OK!

Elapsed: 00:00:12

Reading Phone Info....
SW ver : V 07.00 11-09-12 RM-647 (c) Nokia
IMEI : V 07.00
11-09-12
RM-647
(c) Nokia
PPM : V 07.00
11-09-12
RM-647
(c) Nokia
CNT : V 07.00
11-09-12
RM-647
(c) Nokia
DSP Ver : 07.00
11-09-12
RM-647
(c) Nokia
PCode : V 07.00
11-09-12
RM-647
(c) Nokia
BPCode : V 07.00
11-09-12
RM-647
(c) Nokia
HWID : V 07.00
11-09-12
RM-647
(c) Nokia
LCDVer : V 07.00
11-09-12
RM-647
(c) Nokia
IMEI : V 07.00
11-09-12
RM-647
(c) Nokia
Sl Conf : 2E3-03-00A31312D30
Sl Prof : 392D31320A524D2-D
-----------------------------------sir ufs with best dongle don but--- not don on hwk setup

10-28-2013, 05:11	#1 (permalink)
GsmMunna No Life Poster Join Date: May 2004 Location: A ROUGH ROAD LEADS 2 THE STARS Posts: 3,452 Member: 66937 Status: Offline Thanks Meter: 5,053	UFSx+HWK Release 28/10/2013 - Discussion Release 28/10/2013 WARNING !!! If the HWK is a "TRIAL" or affected by 3rd party tools, this software may not work properly, so use at your own risk. You need to uninstall old HWK Setup Suite and HWK Support Suite and use the new UFSx Support Suite. UFS_DCTxBB5 V 2.3.0.2 ---------------------- 1. BB5 RAPU Based Products USB Flashing / UI support added: RM-884 (302) 2. DCT4 INFINEON Based Products Flashing / UI support added: RM-908,RM-924,RM-925,RM-926,RM-928,RM-929,RM-961,RM-962 (105,210,.. 210,107,106) 3. Added HiBauds (up to 3Mbaud) on UFST Box, for Infineon XG101 and XG110 Platforms. 4. DCT4 MTK Based Products UI support added: RM-944,RM-945 (108) 5. Windows8 64bit support. UFS_ATRz v2.3.0.2 ------------------ 1. Increased Baud Rate for J220,J230 2. Windows8 64bit support. UFS_KZF v2.3.0.2 ----------------- 1. Added Windows8 64 bit Support. UFS_RTP v2.3.0.2 ---------------- 1. Added Windows8 64 bit Support. SeDBx v2.3.0.2 -------------- 1. Added Windows8 64 bit Support. LG v 2.3.0.2 ------------ 1. Common: Windows8 64bit support. SAMs V 2.3.0.2 -------------- SWIFT-AEROFONE E1260B,E1260L added (PUNL,PIM,FL) E1265,E2262 added (UNL,SECT,IM,FL) INFINEON C3322i,C3590,C3592 added (CUNL,PUNL,PIM,FL,UFL) Many thanks to all those who have supported us!!! Official SarasSoft Mirrors:- http://forum.gsmhosting.com/vbb/f311...tions-1216246/ Last edited by Odia The Ultimate; 10-28-2013 at 11:53.

10-31-2013, 19:45	#9 (permalink)
ABUU YUUNUS No Life Poster Join Date: Jul 2006 Location: IBADAN, OYO STATE, NIGERIA Posts: 724 Member: 319112 Status: Offline Thanks Meter: 164	T630 and T610 unlock problem with new RTP module. Dear Odia, I tried today to unlock two sony ericsson phones, T630 and T610 but without success. Each time I clicked on "GO" to get mobile booted, after a few incomplete info, software displays this error " invalid file name". As a result booting process is not completely done and phones couldn't be unlocked. Please what is the way out?

10-28-2013, 11:27	#2 (permalink)
Odia The Ultimate No Life Poster Join Date: Apr 2001 Location: Where dreams become reality. Age: 54 Posts: 5,752 Member: 4042 Status: Offline Thanks Meter: 24,043	Any download links supplied by users in this thread or sub-forum will be removed. Please do not make any thanks posts in this thread, you can use the Thanks button for that. Please do not post anything about why something has not been added or why some model has not been added, or they will be removed. This thread is to discuss the 02.30.00.03 release, nothing else, installation issues should be posted in http://forum.gsmhosting.com/vbb/f311...oblems-822845/

10-28-2013, 11:38	#3 (permalink)
Odia The Ultimate No Life Poster Join Date: Apr 2001 Location: Where dreams become reality. Age: 54 Posts: 5,752 Member: 4042 Status: Offline Thanks Meter: 24,043	The latest release of the Panel software contains a new Backup and Restore Registry option, we urge our customers to use it. 1. Uninstall ALL previous versions, you MUST uninstall HWK Suite BEFORE trying to uninstall HWK Support Suite Setup. 2. Install UFSx Support Suite Setup 3. Connect your UFSx+HWK before running the UFSx Control Panel 4. Run UFSx Control Panel 5. Switch to the "Hardware" Tab 6. If you only have one UFSx connected it will be selected, if more than one, select the check box next to the required UFSx. You can click "Scan Boxes" to refresh the list if you have connected further boxes since opening the Control Panel 7. Click "Check Box" 8. Click "Update Box" 9. Click "Check Box" - Make sure "Box Status" = "True" or "Bad Software" and "Server Status" = "Support Ok", before proceeding 10. Switch to the "Software" Tab 11. Amend "Application Install Path" and/or "Nokia Install Path", if required. 12. Click "Check Server" 13. Click "Install" 14. If you have more than 1 UFSx+HWK run steps 5-13 for each UFSx+HWK (NOTE: You must install something at step 13) 15. Switch to the "Software" Tab 16. Click "Check Box" - Make sure "Box Status" = "True" and "Server Status" = "Support Ok", before proceeding 17. Click "Backup Registry" - Save this file on a removable media. If you decide to re-install Windows, you can Install the setup suite, run the panel and click "Restore Registry", then "Check Box", this process should save you some install logs. The registry backup can also be restored if you get some unexpected auth error when all was working fine before, this happens due to some registry cleaning software.

10-31-2013, 09:58	#6 (permalink)
cpu486 No Life Poster Join Date: Mar 2001 Location: Europe Posts: 561 Member: 3918 Status: Offline Thanks Meter: 15	So, if I want to upgrade from 2.3.0.1 to 2.3.0.2 I have to uninstall all and then install it again. It is not enough to just upgrade. Am I right or ...?

11-01-2013, 11:21	#12 (permalink)
akhtar.abbas No Life Poster Join Date: Dec 2009 Location: pAK+Africa Posts: 1,603 Member: 1190193 Status: Offline Sonork: 1619687 Thanks Meter: 406	MCU SW : V 07.00 11-09-12 RM-647 (c) Nokia PPM SW : V 07.00 11-09-12 RM-647 (c) Nokia IA Platform: Infineon XG110 Prd.Code: 0592312 Bpr.Code: 0589577 Prod.Sn : 3E36681AI HW Vers : 3001 UEM : 1328 UPP : 8850 [2292] LCD Type: WIN:SERI:90 NT7542 IMEI : 358285-04-211272-7 SL Conf : 001-01-00000000000 SL Prof : 000000000003000-2 SL Var : 00003582850421127200 SL Aux : 000B0000 HW Sig : C763CCF910272051 Box Id : FFFFFFFFFFFFFFFF BLK1= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN BLK2= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN BLK3= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN BLK4= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN BLK5= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN BLK6= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN BLK7= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN Provider: GSM Test Equipment UI Defaults Failed Set UI Factory Defaults Failed Set Full Factory Defaults Failed Set Security Failed -------------------------------------------fail sa like old version

11-01-2013, 12:47	#15 (permalink)
akhtar.abbas No Life Poster Join Date: Dec 2009 Location: pAK+Africa Posts: 1,603 Member: 1190193 Status: Offline Sonork: 1619687 Thanks Meter: 406	Test mode set Settings Full Factory Defaults... Set OK! Settings Software Upgrade Defaults... Set OK! Settings Service Centre Defaults... Set OK! Settings Production Tune Defaults... Set OK! Settings User Data Defaults... Set OK! Settings Leave Factory defaults... Set OK! Elapsed: 00:00:12 Reading Phone Info.... SW ver : V 07.00 11-09-12 RM-647 (c) Nokia IMEI : V 07.00 11-09-12 RM-647 (c) Nokia PPM : V 07.00 11-09-12 RM-647 (c) Nokia CNT : V 07.00 11-09-12 RM-647 (c) Nokia DSP Ver : 07.00 11-09-12 RM-647 (c) Nokia PCode : V 07.00 11-09-12 RM-647 (c) Nokia BPCode : V 07.00 11-09-12 RM-647 (c) Nokia HWID : V 07.00 11-09-12 RM-647 (c) Nokia LCDVer : V 07.00 11-09-12 RM-647 (c) Nokia IMEI : V 07.00 11-09-12 RM-647 (c) Nokia Sl Conf : 2E3-03-00A31312D30 Sl Prof : 392D31320A524D2-D -----------------------------------sir ufs with best dongle don but--- not don on hwk setup