Z1010 Loss of Network - GSM-Forum

**Odia The Ultimate** · 08-23-2006, 05:06

Quote:

Originally Posted by mike67

i have a Z1010 that is flashing and customising ok ..but No network after unlocking and the unlock was done by someone else so i do not have any backup of this phone ,, when u insert the sim card phone freezes on searching and no keys work ,, but its not hardware for sure ,,, if i remove sim card all keys work good ,,, so definitely wrong unlocking

Loss of network is usually caused by corrupt/bad GDFS, but I have never seen it lock the phone and then unlock when the SIM card is removed ...

Can you click Info and post the output here, so I can see the status of the phone, also make a backup of the GDFS using Read (GDFS Area) and Read GDFS options just in case you need it later.

Odia.

mike67 · 08-23-2006, 17:04

Thanks Odia

Here is the screenshot and i am also sending the GDFS file and also the Initial backup when the phone came to me first ..Also remember i did not unlock this phone so i dont have the original back up

But i trie to flash it with different files from HWK and here is the Screen shot of Info Flash and Unlock .. 2 Mcu files Flashed and than the Cust/FS seperate and unlock and Info ....

McuId: 71000301FFFFFF, CID: 16, 4 (Red)
Mcert: A1_SEMC_3
Baud Rate: 460800
Trying: CXC1325413_040614_1539_R3M{0101020301}.bin
Trying: CXC1325413_040614_1539_R3M{0101020101}.bin
PayLoader Certificate Accepted
Prolgue Ok
PayLoader: 040614 1539 LLECXC1325413_CERTLOADER R3M, Ok
IMEI : 353456-00-029941-0, CID: 16, CDT: 1 0 1 (Red)
FlId0: 8964, Intel 640W18TD
OTP_F: 19629A01174020FE - Locked
OTP_U: 0080B06405504F07 - Locked
FlId1: 8964
OTP_F: 08629A0117407C99 - Locked
OTP_U: FFFFFFFFFFFFFFFF - Open
FlId2: 896C
OTP_F: 0D93A8013340ACDC - Locked
OTP_U: FFFFFFFFFFFFFFFF - Open
041109 1252 GOHCXC125904_SEMC_VIOLA_FILE_SYSTEM_LOADER_R1E
ITP Sw : CXC 125 631 R1K
Brand :
CUST Lp: EMEA_3
CDA ver:
CXC ver: cxc125677 R1G007
CustBundle: Z1010_CDA102239-25_TELE2_GL_SV_R5A.bib
Folder/File Exists, Skipped: /tpa
Folder/File Exists, Skipped: /tpa/preset
Folder/File Exists, Skipped: /tpa/preset/custom
CUST Flashing Done, Time: 00:16
McuId: 71000301FFFFFF, CID: 16, 4 (Red)
Mcert: A1_SEMC_3
Baud Rate: 460800
Trying: V800_CXC1325414_050103_1324_R3S_{0101020301}.bin
PayLoader Certificate Rejected :00 46 32 A9 DA
Trying: CXC1325414_040716_1009_R3M{0101020101}.bin
PayLoader Certificate Accepted
Prolgue Ok
PayLoader: 040614 1100 LLECXC1325414_FLASHLOADER R3M, Ok
IMEI : 353456-00-029941-0, CID: 16, CDT: 1 0 1 (Red)
FlId0: 8964, Intel 640W18TD
Security Backup: Z1010_35345600029941_23082006_61303.sim
IMEI : 353456-00-029941-0
OTP CID: 16, GDFS CID: 16
ULCK : 0000 - Off
NCK : Open [5-5] 246-01
NSCK : Open [5-5] 246-01
SPCK : Open [5-5] 246-01
CCK : Open [5-5] 246-01
PCK : Open [5-5] 246-01
ESLK : Open [5-5]
Flags : 01FFFFFFFFFFFFFFFFFF [UMTS]
Model : Z1010
Brand :
CUST Lp: EMEA_3
CDA ver:
CXC ver: cxc125677 R1G007

INFO

McuId: 71000301FFFFFF, CID: 16, 4 (Red)
Mcert: A1_SEMC_3
Baud Rate: 460800
Trying: V800_CXC1325414_050103_1324_R3S_{0101020301}.bin
PayLoader Certificate Rejected :00 46 32 A9 DA
Trying: CXC1325414_040716_1009_R3M{0101020101}.bin
PayLoader Certificate Accepted
Prolgue Ok
PayLoader: 040614 1100 LLECXC1325414_FLASHLOADER R3M, Ok
IMEI : 353456-00-029941-0, CID: 16, CDT: 1 0 1 (Red)
FlId0: 8964, Intel 640W18TD
Security Backup: Z1010_35345600029941_23082006_62742.sim
IMEI : 353456-00-029941-0
OTP CID: 16, GDFS CID: 16
ULCK : 0000 - Off
NCK : Open [5-5] 246-01
NSCK : Open [5-5] 246-01
SPCK : Open [5-5] 246-01
CCK : Open [5-5] 246-01
PCK : Open [5-5] 246-01
ESLK : Open [5-5]
Flags : 01FFFFFFFFFFFFFFFFFF [UMTS]
Model : Z1010
Brand : Tele2
CUST Lp: EU_3
CDA ver: CDA102239/25 R5A
CXC ver: cxc125677 R1K010

GDFS FILE :

mike67 · 08-23-2006, 17:29

This is the GDFS read by HWK software ,,, with add dummy certificate ticked

the abpve gdfs is the one that was used to unlock the phone by someone else ..

mike67 · 08-23-2006, 17:33

Actually the phone is frozen ,,, without simcard phone works fine ,, all keys work ,, but as soon as i start with sim card everything freezes and searching .. and it can stay like that until battry drains out after 6-8 hrs

So bro please help me with the solution cuz i searched the forum and it seems many people have this problem but No solution ...

thanks again for your help Odia ,, i really appreciatte your support
Mike

**Odia The Ultimate** · 08-23-2006, 19:01

I cannot see a problem in the Info or the flash log output, all seems to be fine.

Can I just check are you testing with a UMTS (3G) simcard or not? Or are you expecting the unlock to allow 2G operation?

Odia.

mike67 · 08-23-2006, 22:43

Yes i dont have 3G in my country but i put a 3G sim card of 3 UK and it still freezes ... ofcourse there wud be no network but atleast it shudnt freeze right ...?

And what is the solution to use 2g CARD CAUSE the owner says he was using a 2G card before ,,, and than it started to freeze on him ...

So any solution boss ..?

Thanks again Odia for yr reply
Mike

**Odia The Ultimate** · 08-24-2006, 06:14

Quote:

Originally Posted by mike67

Yes i dont have 3G in my country but i put a 3G sim card of 3 UK and it still freezes ... ofcourse there wud be no network but atleast it shudnt freeze right ...?

Aha ok, so now we maybe getting somewhere ...

As I have said I have never seen the freeze problem before, but I would guess its due to bad calibration data in the phone, also maybe the other person who did the unlock did it via uploading an alien GDFS, which would explain the bad GDFS ...

You will notice that the Flags: for the phone is 01FF... this is UMTS only, you would need to do an InitSB and add the further band locks for GSM, I also think you would need to add some flags in the GDFS to allow 2G/3G network selection, try adding the further bandlocks first and see what happens.

It could also be the firmware version, maybe ealier firmware did not allow 2G operation and later firmware did, I am just guessing as I have not seen the Z1010 and tried to convert to 2G operation.

But I think you need a good GDFS and I dont think one has been posted for the Z1010, so maybe you need to ask in the forum. (anyone reading this has a good GDFS please attach here)

Odia.

**Odia The Ultimate** · 08-24-2006, 06:35

Quote:

Originally Posted by Odia The Ultimate

But I think you need a good GDFS and I dont think one has been posted for the Z1010

Check the KZF Special folder, it contains both BIN and GDF version of the Z1010 GDFS.

Odia.

mike67 · 08-24-2006, 12:24

OK lets take this step by step ,,,

1). So how do i rectify the calibaration data ?

2). And yes i have notice the UMTS only .. the GDFS which i sent u says OAFFFFFFFFFFFFFFF (????) after init SB so i changed it to 1F but even with OAFFFFFFFFFFFFFFF it does the same thing

3) yes i need a GDFS that works with 2G but everyone sends me in either the cruiser format or Sonics

Hoping for your reply

Thanks
Mike

mike67 · 08-24-2006, 12:25

I did check the special folder .. Now tell me do i restore both the BIN and GDFS if YES .. they are both for CID 29 is it ok to do that ?

thanks
Mike

cliffrock4u005 · 08-24-2006, 12:46

Well Mike i might have the GDFS u are looking for

mike67 · 08-24-2006, 13:02

@cliffrock4u005

Hey mate is it CID 16 or 29 ? Either ways can u send it to me please if possible either by email or msn or post it here please

muna66@hotmail.com

thanks
Mike

cliffrock4u005 · 08-24-2006, 13:04

Hey I have both of them and do u have yahoo id mine is mobileman_005@yahoo.com well i am online right now

**Odia The Ultimate** · 08-24-2006, 14:16

Quote:

Originally Posted by mike67

1). So how do i rectify the calibaration data ?

Nomal user cannot, you need special RF equipment to carry this out, your only other option is to find a best fit GDFS e.g. on that does not cause the phone to freeze.

Quote:

Originally Posted by mike67

2). And yes i have notice the UMTS only .. the GDFS which i sent u says OAFFFFFFFFFFFFFFF (????) after init SB so i changed it to 1F but even with OAFFFFFFFFFFFFFFF it does the same thing

I will assume you mean 0AFFFFFFFFFFFFFFFFFF but you would need to combine both 2G and 3G, check out InitSB and tick the required options.

In regards to the GDFS you can write the BIN or GDF, I perfer BIN, the GDF is useful for tweeking the GDFS, e.g. to enable the 2G/3G selection menu in this case, but you would need to know the GDFS block, record and bit(s) to change.

The CID 29 v CID 16 should not be a problem, just InitSB and it should recover the GDFS mis-match. If not you can do a Flash Rec to change the GDFS CID back to 16.

Odia.

mike67 · 08-24-2006, 17:30

I tried the Bip file but still the same and after that phone still freezing ,, but i dont know how to combine the bands i mean 2G and 3G man this is the first time i have come across such problem ... maybe i will try the GDFS file the person in this thread has promised me ,,

thanks again Odia
Mike

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
iphone 3g sometimes loss of network	orangade	iPhone ,iPod & iPad (Apple Inc. Products)	3	03-14-2010 00:36
Is There Any Relation to Unlocking and Loss of network...please answer 911GT	harim_1981	MT-BOX	10	10-23-2007 09:49
T28 & T29 problem causing loss of network	::Yasir::	Old Ericsson Phones & Sony Phones	9	02-19-2004 10:18
3330 ringtones slow and loss of reception	joakes	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	1	04-09-2002 06:01
6210 loss of signal (not due to flashing)	wildwhacker	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	0	07-31-2001 18:47

08-23-2006, 17:33	#4 (permalink)
mike67 No Life Poster Join Date: Nov 2005 Location: USA Posts: 1,148 Member: 197538 Status: Offline Thanks: 104 Thanked 97 Times in 67 Posts	Actually the phone is frozen ,,, without simcard phone works fine ,, all keys work ,, but as soon as i start with sim card everything freezes and searching .. and it can stay like that until battry drains out after 6-8 hrs So bro please help me with the solution cuz i searched the forum and it seems many people have this problem but No solution ... thanks again for your help Odia ,, i really appreciatte your support Mike

08-23-2006, 19:01	#5 (permalink)
Odia The Ultimate Product Manager Join Date: Apr 2001 Location: Where dreams become reality. Age: 43 Posts: 5,530 Member: 4042 Status: Offline Thanks: 56 Thanked 21,856 Times in 1,078 Posts	I cannot see a problem in the Info or the flash log output, all seems to be fine. Can I just check are you testing with a UMTS (3G) simcard or not? Or are you expecting the unlock to allow 2G operation? Odia.

08-23-2006, 22:43	#6 (permalink)
mike67 No Life Poster Join Date: Nov 2005 Location: USA Posts: 1,148 Member: 197538 Status: Offline Thanks: 104 Thanked 97 Times in 67 Posts	Yes i dont have 3G in my country but i put a 3G sim card of 3 UK and it still freezes ... ofcourse there wud be no network but atleast it shudnt freeze right ...? And what is the solution to use 2g CARD CAUSE the owner says he was using a 2G card before ,,, and than it started to freeze on him ... So any solution boss ..? Thanks again Odia for yr reply Mike

08-24-2006, 12:24	#9 (permalink)
mike67 No Life Poster Join Date: Nov 2005 Location: USA Posts: 1,148 Member: 197538 Status: Offline Thanks: 104 Thanked 97 Times in 67 Posts	OK lets take this step by step ,,, 1). So how do i rectify the calibaration data ? 2). And yes i have notice the UMTS only .. the GDFS which i sent u says OAFFFFFFFFFFFFFFF (????) after init SB so i changed it to 1F but even with OAFFFFFFFFFFFFFFF it does the same thing 3) yes i need a GDFS that works with 2G but everyone sends me in either the cruiser format or Sonics Hoping for your reply Thanks Mike

08-24-2006, 12:25	#10 (permalink)
mike67 No Life Poster Join Date: Nov 2005 Location: USA Posts: 1,148 Member: 197538 Status: Offline Thanks: 104 Thanked 97 Times in 67 Posts	I did check the special folder .. Now tell me do i restore both the BIN and GDFS if YES .. they are both for CID 29 is it ok to do that ? thanks Mike

08-24-2006, 12:46	#11 (permalink)
cliffrock4u005 Freak Poster Join Date: Jul 2003 Location: india Age: 29 Posts: 267 Member: 35563 Status: Offline Thanks: 2 Thanked 4 Times in 4 Posts	Well Mike i might have the GDFS u are looking for

08-24-2006, 13:02	#12 (permalink)
mike67 No Life Poster Join Date: Nov 2005 Location: USA Posts: 1,148 Member: 197538 Status: Offline Thanks: 104 Thanked 97 Times in 67 Posts	@cliffrock4u005 Hey mate is it CID 16 or 29 ? Either ways can u send it to me please if possible either by email or msn or post it here please muna66@hotmail.com thanks Mike

08-24-2006, 13:04	#13 (permalink)
cliffrock4u005 Freak Poster Join Date: Jul 2003 Location: india Age: 29 Posts: 267 Member: 35563 Status: Offline Thanks: 2 Thanked 4 Times in 4 Posts	Hey I have both of them and do u have yahoo id mine is mobileman_005@yahoo.com well i am online right now

08-24-2006, 17:30	#15 (permalink)
mike67 No Life Poster Join Date: Nov 2005 Location: USA Posts: 1,148 Member: 197538 Status: Offline Thanks: 104 Thanked 97 Times in 67 Posts	I tried the Bip file but still the same and after that phone still freezing ,, but i dont know how to combine the bands i mean 2G and 3G man this is the first time i have come across such problem ... maybe i will try the GDFS file the person in this thread has promised me ,, thanks again Odia Mike