MY 501C unlock problem - GSM-Forum

arimob · 03-20-2007, 14:42

Hello
I am sorry maybe has been so much disccusing about this problem but I have another one.
I have my 5001c I did all disamble pgone conect battery conect the Adapter but I didnt have a charger. The phone is powered one by adapter but program dont read it. In Auto speed apear change speed settings and in ohere speed stteting like 19200 apears Failed to read imei. Where is problem. Could be reason of the problem that I didnt use an charger.

Thank you for cooperation

Best
Ari MOb

Oxo_Boxo · 03-20-2007, 17:03

There is TP adapters not compatible with SagDD TP cable!
Better solder TP wires as we show in TP picture!

BR

Multi-COM · 03-20-2007, 21:00

Please note that always check what cable you ordered and what cable you got - on our page each customer can choose if they want SagDD metal Box, palstic Box or SCDR cable but as I saw many of our resseler don't even mention this - they sell adapters as they are and customer buy them but cable are diffrent for diffrent devices and this are here main problem. TP are workign withtou any problems at all with:
1) LCD connected for 501C models and 401Z (for both of these models LCD must be connected)
2) Properly installed cable - factory made RJ45 goes to device and manual punched cable to adapter
3) Charger connected in case of reading problems - it's uses miniUSB connector
Ofcourse these are only valid if you got correct cable so not for diffrent device, you can check by link that Latigido gives here

arimob · 03-21-2007, 11:12

Dear Sir
I bought the testpoint directly from you Multi Com (ordered at site www.gsmzone.net) and I receive the testpoing with special cable. The testpoint is with switch and the cable. where can be a problem

Best
Arimob

Multi-COM · 03-21-2007, 20:44

@arimob: make sure that you connect factory made to Box and manually made to adapter - please then if you got few minutes contact my by Sonork or ICQ so we can check Online where are problem, we sold many of these by ourself as to our resselers and most of problem (adapter gettign hot etc) are wrong cable or wrong punching/moulding RJ45...anyway I can help you Online in this

sweddy · 03-23-2007, 13:14

I have a sagem myv-76 I want to unlock it but i dont know the right box to use please help me to solve this problem if possible

Oxo_Boxo · 03-23-2007, 15:47

myV-76 are same as myX6-2 and can't be unlocked till now via ANY box!

arimob · 03-27-2007, 13:05

DO you have the scheme of the cable I am dont know if is cable or not I had today anotherone and he didnt read it at all. Is there any possibilities to ha the scheme to check if is right cable or to modify them.

Best

Ari mob

arimob · 03-28-2007, 09:59

Quote:

Originally Posted by Multi-COM

@arimob: make sure that you connect factory made to Box and manually made to adapter - please then if you got few minutes contact my by Sonork or ICQ so we can check Online where are problem, we sold many of these by ourself as to our resselers and most of problem (adapter gettign hot etc) are wrong cable or wrong punching/moulding RJ45...anyway I can help you Online in this

I dont have sonork or IQ can we co0ntact via msn I allready add you addres on my msn

Multi-COM · 03-28-2007, 22:48

OK - we are onLine usually from 9 to 16 CET

ReyTech · 04-02-2007, 08:00

@Mutli-com
I too hve the same problem! it gives error "PROBLEM: Setting phone speed failed!" im waiting for you online!
WBR
ReyTech,

03-20-2007, 14:42	#1 (permalink)
arimob No Life Poster Join Date: May 2005 Age: 61 Posts: 556 Member: 147694 Status: Offline Thanks Meter: 69	MY 501C unlock problem Hello I am sorry maybe has been so much disccusing about this problem but I have another one. I have my 5001c I did all disamble pgone conect battery conect the Adapter but I didnt have a charger. The phone is powered one by adapter but program dont read it. In Auto speed apear change speed settings and in ohere speed stteting like 19200 apears Failed to read imei. Where is problem. Could be reason of the problem that I didnt use an charger. Thank you for cooperation Best Ari MOb

03-20-2007, 21:00	#3 (permalink)
Multi-COM No Life Poster Join Date: Nov 2003 Location: Poland Age: 46 Posts: 2,759 Member: 43823 Status: Offline Thanks Meter: 308	Please note that always check what cable you ordered and what cable you got - on our page each customer can choose if they want SagDD metal Box, palstic Box or SCDR cable but as I saw many of our resseler don't even mention this - they sell adapters as they are and customer buy them but cable are diffrent for diffrent devices and this are here main problem. TP are workign withtou any problems at all with: 1) LCD connected for 501C models and 401Z (for both of these models LCD must be connected) 2) Properly installed cable - factory made RJ45 goes to device and manual punched cable to adapter 3) Charger connected in case of reading problems - it's uses miniUSB connector Ofcourse these are only valid if you got correct cable so not for diffrent device, you can check by link that Latigido gives here Last edited by Multi-COM; 03-20-2007 at 21:52.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
My 501c unlock problem	msantar	SAGEM JTAG UNLOCKER	5	11-26-2009 04:54
my 501c unlock problems	GSM FREE	SAGEM JTAG UNLOCKER	1	08-06-2009 13:07
Sagem my 501c unlocking cable	hussainafridi	Basic Micro-Box Software Support (SAMSUNG, HUAWEI, etc...)	3	03-13-2009 10:58
my 501c unlocking	ZEBUN	SCDR II	1	07-22-2008 09:48
My 501c Unlocking	ZEBUN	SagMaster	0	07-21-2008 21:00

03-20-2007, 17:03	#2 (permalink)
Oxo_Boxo No Life Poster Join Date: Jun 2002 Location: East Europe Age: 51 Posts: 3,950 Member: 12837 Status: Offline Thanks Meter: 2,740	There is TP adapters not compatible with SagDD TP cable! Better solder TP wires as we show in TP picture! BR

03-21-2007, 11:12	#4 (permalink)
arimob No Life Poster Join Date: May 2005 Age: 61 Posts: 556 Member: 147694 Status: Offline Thanks Meter: 69	Dear Sir I bought the testpoint directly from you Multi Com (ordered at site www.gsmzone.net) and I receive the testpoing with special cable. The testpoint is with switch and the cable. where can be a problem Best Arimob

03-21-2007, 20:44	#5 (permalink)
Multi-COM No Life Poster Join Date: Nov 2003 Location: Poland Age: 46 Posts: 2,759 Member: 43823 Status: Offline Thanks Meter: 308	@arimob: make sure that you connect factory made to Box and manually made to adapter - please then if you got few minutes contact my by Sonork or ICQ so we can check Online where are problem, we sold many of these by ourself as to our resselers and most of problem (adapter gettign hot etc) are wrong cable or wrong punching/moulding RJ45...anyway I can help you Online in this

03-23-2007, 13:14	#6 (permalink)
sweddy Junior Member Join Date: Mar 2007 Posts: 5 Member: 473200 Status: Offline Thanks Meter: 0	I have a sagem myv-76 I want to unlock it but i dont know the right box to use please help me to solve this problem if possible

03-23-2007, 15:47	#7 (permalink)
Oxo_Boxo No Life Poster Join Date: Jun 2002 Location: East Europe Age: 51 Posts: 3,950 Member: 12837 Status: Offline Thanks Meter: 2,740	myV-76 are same as myX6-2 and can't be unlocked till now via ANY box!

03-27-2007, 13:05	#8 (permalink)
arimob No Life Poster Join Date: May 2005 Age: 61 Posts: 556 Member: 147694 Status: Offline Thanks Meter: 69	DO you have the scheme of the cable I am dont know if is cable or not I had today anotherone and he didnt read it at all. Is there any possibilities to ha the scheme to check if is right cable or to modify them. Best Ari mob

03-28-2007, 22:48	#10 (permalink)
Multi-COM No Life Poster Join Date: Nov 2003 Location: Poland Age: 46 Posts: 2,759 Member: 43823 Status: Offline Thanks Meter: 308	OK - we are onLine usually from 9 to 16 CET

04-02-2007, 08:00	#11 (permalink)
ReyTech No Life Poster Join Date: Apr 2005 Location: india Posts: 1,410 Member: 135945 Status: Offline Thanks Meter: 85	@Mutli-com I too hve the same problem! it gives error "PROBLEM: Setting phone speed failed!" im waiting for you online! WBR ReyTech,