Alcatel 6012x Unbrick / Language Change [EU-CH-Spain, Bulgaria, Arabic, etc.]

[alex ionut]

forced flash mode means by raw data ? using write from option ?

by flashing this rom again i get error 4032 enable dram failed but when tryed to flash that ROM_0 i get error 5054 enable dram setting fail, what could be the problem ?

[Brka]

Originally Posted by alex ionut

forced flash mode means by raw data ? using write from option ?

by flashing this rom again i get error 4032 enable dram failed but when tryed to flash that ROM_0 i get error 5054 enable dram setting fail, what could be the problem ?

Does the phone accepts Format ?

Forced flash mode = Volume up + power on + insert usb cable.

b.r.
Alex

[alex ionut]

i select autoformat whole flash and click start then keep pressing vol up + power? then connect to pc?

did i not mentioned that the phone is dead no chage icon no prealoder vcom in device manager?, the only thing that works on it its a blue led and its detected as mtk usb port(COM) in pc i think its meta mode, i don't have any backup, when i try to format whole flash using that scatter file still get the error 4032 enable Dram failed how to know if the phone supports format ?

[Brka]

two things :

1st - You have bricked (Hard bricked) phone, probably no solution.
2nd - STOP spamming the board, and writing message by message.

b.r.
Alex

[alex ionut]

ok im sorry. i did my best.
Best regards Alex

[moro2004]

why slplash tool ask me a legaly name of scatter file?

[gevorgmik]

Hello
I have the same problem.
I bricked my Alcatel 6012X while flashing it via SP flashtool.
Flashing went well, but phone didn't turn on.
Now it recognizes as MTK device, but when I try to flash I get errors (or 4032 , eiter 5054)
I tried to flash it's 6012X's original firmware and the debranded rom I found above.
In box is written 6012X-2BTWIE1
I couldn't find this firmare to try.
Please if you can help me with this problem.

[young_floyd]

Originally Posted by Brka

two things :

1st - You have bricked (Hard bricked) phone, probably no solution.
2nd - STOP spamming the board, and writing message by message.

b.r.
Alex

if I try to flash and the device is recognized as USB MTK port, it means I Have a hard bricked phone?

[Brka]

Originally Posted by young_floyd

if I try to flash and the device is recognized as USB MTK port, it means I Have a hard bricked phone?

If it doesn't accept correct preloader (preloader only, not full flash),
then it's bricked.

correct procedure is :

- FULL Format, with bootloader
- holding volume down or up, or both + power on and insert USB cable
- Flash preloader only from spft,
- After that phone accepts normal flash
- Fully flash phone, or flash TWRP and restore backup from sdcard

I have attached boot recovery pack - download HERE
Also, attached different scatter file, which can be problem also.

b.r.
Alex

[young_floyd]

Originally Posted by Brka

If it doesn't accept correct preloader (preloader only, not full flash),
then it's bricked.

correct procedure is :

- FULL Format, with bootloader
- holding volume down or up, or both + power on and insert USB cable
- Flash preloader only from spft,
- After that phone accepts normal flash
- Fully flash phone, or flash TWRP and restore backup from sdcard

I have attached boot recovery pack - download HERE
Also, attached different scatter file, which can be problem also.

b.r.
Alex

I have 2 questions about your procedure:

1: to flash preloader from sptf shall I use the one that is on your boot recovery pack?
2: the full flash should contain cache and user data?

[young_floyd]

Originally Posted by young_floyd

I have 2 questions about your procedure:

1: to flash preloader from sptf shall I use the one that is on your boot recovery pack?
2: the full flash should contain cache and user data?

I answer my self.

1: I did used the preloader from your pack
2: I used the full flash you uploaded on post #23

for now phone is on, but got imei invalid, now I'm flashing Rom_0 from post #3 and write results!

[young_floyd]

Originally Posted by young_floyd

I answer my self.

1: I did used the preloader from your pack
2: I used the full flash you uploaded on post #23

for now phone is on, but got imei invalid, now I'm flashing Rom_0 from post #3 and write results!

As bRkA said, imei invalid can be solved, just read carefully his instructions and the phone will be working again, I flashed phone with rom from post #3 and got original imei back, and even spanish language.

[enjoysunfire]

Hi,

Will it work for an OT-6012A ?

Originally Posted by Brka

There you go .... debranded rom, for SPFlashTool.

Flash it with "Write Memory" option.

if after flashing, doesn't boot to system, or have bootloop,
do format/wipe data/cache.

7zip to unpack ....


p.s. it also solves all imei/nvram related problems, returns original imei back,
which stays after reset.

thanx to Russian forums for initial solution.

press thanx if it was usefull for you.

b.r.
Alex

[enjoysunfire]

I tried and it works now! My phone was "locked" with the message "The slot has been permanently locked" (due to too many attemps for simunlock it).

[polyctro]

Thank you guys, it helped me to bring my phone alive...