Alcatel OT 8000D Firmware/ROM needed

[zizoux07]

Originally Posted by Brka

Be warned that you can easily brick your device.

Under bricked, I mean HARD BRICKED. And it wont be easy to repair.
Qualcomm MSM8225 Snapdragon S4 Play is inside OT Scribe Easy (ot-8000D).

FULL Rom image -
Cloning tool, to write ROM -

Instruction :

- Put phone to download mode (Volume up + Volume down + insert cable to phone)
- Start image writing software, it should see eMMC drive
- If not, use OTU updater for that model, start it, when detecting phone, kill OTU process from windows, use clone software
- Copy mode : IMAGE to DRIVE
- Select image file, and select destination drive (eMMC 4Gb drive)
- Check option "Copy free areas" in advanced options
- Press start, at the end of copying, message come "how to create a partition table?" - Choose "automatically"
- After done, exit the program. Disconnect the phone.
- Turn on (long press the power button).

that's it.

b.r.
Alex

is it the official stock rom for the onetouch scribe easy 8000d? if so how to flash it on a bricked phone (I guess) ?

[El_Nahy]

Originally Posted by Brka

Download - HERE

b.r.
Alex

please help Brka

i have 8000d it was working fine but infected with monkey test
tried to flash it now it's dead just detect QDloader 9008

how to revive it again???

tried with ONE TOUCH Upgrade Q 2.7.1 and it's error cannot find desk

Help please

with otu

[Brka]

Try with utility I posted in THIS thread,
and if finish successfully, you will have phone visible by OTU Updater.

b.r.
Alex

[TOTOS.POPOS]

I need alcatel 8000d arabic firmware please

[papu3090]

i have 8000d it's dead just detect QDloader 9008

[MiRoOo]

Someone with a working phone contains Arabic language can easily pull the whole mmcblk image through adb or even with HDClone.




Sent from my iPhone 6 using Tapatalk.

[Brka]

Originally Posted by papu3090

i have 8000d it's dead just detect QDloader 9008

First, before ANYTHING ELSE, check battery voltage.
It MUST be over 3.75v. If it's not, CHARGE IT first.

Then ....

Try with THIS Archive.

Open device manager, to be able to see when Port 9008 appaears,
and (fortunately) if it goes well, Port 9006 together with new hard drive
(eMMC storage device under hard disks section).


Unpack and try go.cmd from folder "1", and other folders.
Result should be qblank flash with some error, and new port / drive.

If that fails ... your phone is PROBABLY a total brick, with malfunctioned eMMC memory.

But ... if eMMC drive appears ... post here, I will give link
with full eMMC image, that can be written with HDClone, and phone should be unbricked.

b.r.
Alex

[m u prince]

I need alcatel one touch 8000d flash file
alcatel one touch 8000d flash file
how to Flashing alcatel one touch 8000d Plz Help me

[Brka]

Originally Posted by m u prince

I need alcatel one touch 8000d flash file
alcatel one touch 8000d flash file
how to Flashing alcatel one touch 8000d Plz Help me

Try with official OTU Updater, download - HERE

b.r.
Alex

[Romu]

Hello
Please i need urgently alcatel OT-8000a firmware. Alcatel one touch scribe easy 8000a.
Thanks

[emmaugoh]

Brka pls sir is there any possible way I can restore an 8000d that shows encryption failed after booting successful... Not realy encryption failed but it comes with different language telling me to click two icon, one is a good mark like Nike and the other is in red cancel form.

After that it reboot and hang one boot menu

[Brka]

Originally Posted by emmaugoh

Brka pls sir is there any possible way I can restore an 8000d that shows encryption failed after booting successful... Not realy encryption failed but it comes with different language telling me to click two icon, one is a good mark like Nike and the other is in red cancel form.

After that it reboot and hang one boot menu

If it still shows "encryption bla bla" after making wipe data/cache,
eMMC (flash memory) probably went into read-only state,
and solutions are : reflowing eMMC, repairing it with some eMMC box,
or changing eMMC with new one.

b.r
Alex

[emmaugoh]

Originally Posted by Brka

If it still shows "encryption bla bla" after making wipe data/cache,
eMMC (flash memory) probably went into read-only state,
and solutions are : reflowing eMMC, repairing it with some eMMC box,
or changing eMMC with new one.

b.r
Alex

I just found out It was the recovery menu...... The image file you uploaded is it for single sim also because this one is a single sim 8000D with ThL at boot up , if can u re-upload the clone tool file again, I will be happy thanks

*** merged post ***

BRKA, the problem now is, Is there a way to trick updater tool to update the phone. After it detects the phone... It shows your have the latest version and stops... If I can get the updater to update the phone.. My problem would be solved..... Thanks for your earlier response

*** merged post ***

Brka, sir am awaiting your response regarding making the the update utility force update the os and if the one u posted is for one SIM also, I don't mind flashing it,,

Thanks in anticipation of your response.

[Brka]

Contact me via PM, maybe we can sort it out remotely.

p.s. Dont play with the phone, you may end with total brick.

b.r.
Alex

[scorpian1982]

Originally Posted by Brka

Be warned that you can easily brick your device.

Under bricked, I mean HARD BRICKED. And it wont be easy to repair.
Qualcomm MSM8225 Snapdragon S4 Play is inside OT Scribe Easy (ot-8000D).

FULL Rom image - HERE
Cloning tool, to write ROM - HERE

Instruction :

- Put phone to download mode (Volume up + Volume down + insert cable to phone)
- Start image writing software, it should see eMMC drive
- If not, use OTU updater for that model, start it, when detecting phone, kill OTU process from windows, use clone software
- Copy mode : IMAGE to DRIVE
- Select image file, and select destination drive (eMMC 4Gb drive)
- Check option "Copy free areas" in advanced options
- Press start, at the end of copying, message come "how to create a partition table?" - Choose "automatically"
- After done, exit the program. Disconnect the phone.
- Turn on (long press the power button).

that's it.

b.r.
Alex

Thanks alot sir Perfect working file + procedure, Well Done