N70 Dead after changed language - GSM-Forum

mccm · 07-04-2006, 07:13

Now phone stuck at Nokia with no leds then power off.

This is a new phone,how to retrieve it?

Cables had add 5.1k resistor,disabled VPP while flashing & factory default setting check.

Heres the log:

VPP is DISABLED.
Processing File: RM84_50616203.C0
Boot...
rap3gv2_2nd.fg
RAP3Gv3_algo.fg
helen3_2nd.fg
h3_sam_nand_gbbm.fg
Erase RAP3 [00000000 - 0052AB9D]
Erase RAP3 [006A0000 - 006BFFFF]
Erase RAP3 [006DF000 - 006EFFFF]
Erase RAP3 [00700000 - 007EFFFF]
Erase APE [00000000 - 0000FFFF]
Erase APE [00010000 - 0001FFFF]
Erase APE [00020000 - 000203FF]
Erase APE [00050000 - 03ECFFFF]
Erase[68.92 MB]...
Waiting response for 320 Sec...in 7.46s
Flash[31.17 MB]...in 86.11s
* * Processed file in 100.91 seconds
Processing File: RM84_50616203_v2.V15
Boot...
rap3gv2_2nd.fg
RAP3Gv3_algo.fg
helen3_2nd.fg
h3_sam_nand_gbbm.fg
Erase APE [01DE0000 - 028FFFFF]
Erase APE [02900000 - 03ECFFFF]
Erase[32.94 MB]...
Waiting response for 320 Sec...in 3.59s
Flash[6.05 MB]...in 18.30s
* * Processed file in 29.22 seconds
* * * Phone flashing done in 2:16 minutes
Post Flash serial tunning of phone....
Pooling mode for full factory set...
Phone not responding, try to set manually!

mccm · 07-04-2006, 16:34

Any one can help or address my problem?

Please........

stefanusrudy · 07-06-2006, 10:14

hi,
try enable low level format before content.

regards

mccm · 07-06-2006, 23:30

thanks for your reply,as I send to the SC to reload the software cos it was a customised version for specific teco i-mode.

We dont have the software out yet,waiting for the solution to decustomise this type of phones,any ideas?

Support not seen to be as good as the past,sad.

stefanusrudy · 07-07-2006, 05:58

hi,
what was phone original version?
(then you flash it with 50616203) if same version, or original version is lower, shouldn't have any problem...
but there're so many thing that we don't understand about bb5, i have ever flashed 6680 with same version also dead, flash again didn't help. only higher version can revive it..

07-04-2006, 07:13	#1 (permalink)
mccm No Life Poster Join Date: Aug 2005 Posts: 2,351 Member: 173565 Status: Offline Thanks: 158 Thanked 68 Times in 60 Posts	N70 Dead after changed language Now phone stuck at Nokia with no leds then power off. This is a new phone,how to retrieve it? Cables had add 5.1k resistor,disabled VPP while flashing & factory default setting check. Heres the log: VPP is DISABLED. Processing File: RM84_50616203.C0 Boot... rap3gv2_2nd.fg RAP3Gv3_algo.fg helen3_2nd.fg h3_sam_nand_gbbm.fg Erase RAP3 [00000000 - 0052AB9D] Erase RAP3 [006A0000 - 006BFFFF] Erase RAP3 [006DF000 - 006EFFFF] Erase RAP3 [00700000 - 007EFFFF] Erase APE [00000000 - 0000FFFF] Erase APE [00010000 - 0001FFFF] Erase APE [00020000 - 000203FF] Erase APE [00050000 - 03ECFFFF] Erase[68.92 MB]... Waiting response for 320 Sec...in 7.46s Flash[31.17 MB]...in 86.11s * * Processed file in 100.91 seconds Processing File: RM84_50616203_v2.V15 Boot... rap3gv2_2nd.fg RAP3Gv3_algo.fg helen3_2nd.fg h3_sam_nand_gbbm.fg Erase APE [01DE0000 - 028FFFFF] Erase APE [02900000 - 03ECFFFF] Erase[32.94 MB]... Waiting response for 320 Sec...in 3.59s Flash[6.05 MB]...in 18.30s * * Processed file in 29.22 seconds * * * Phone flashing done in 2:16 minutes Post Flash serial tunning of phone.... Pooling mode for full factory set... Phone not responding, try to set manually!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
N70 dead after change new tahvo	M1ngsan	Nokia Hardware & Hardware-Repair Area	12	01-09-2010 05:56
n70 dead after changing power switch, no pwr, no charge!	DjDecibel	Nokia Hardware & Hardware-Repair Area	6	07-24-2009 10:31
N70 dead after changing lcd driver	east asia link	Nokia Hardware & Hardware-Repair Area	4	02-21-2007 20:03
x300 dead after changing language	zata222	Redbox	10	04-04-2006 17:41
be4 dead after changing language .	makona	Alcatel & TCL Old Models	5	11-16-2001 11:58

07-04-2006, 16:34	#2 (permalink)
mccm No Life Poster Join Date: Aug 2005 Posts: 2,351 Member: 173565 Status: Offline Thanks: 158 Thanked 68 Times in 60 Posts	Any one can help or address my problem? Please........

07-06-2006, 10:14	#3 (permalink)
stefanusrudy No Life Poster Join Date: Mar 2005 Location: S7°1x'xxx" - E112°4x'xxx" Posts: 2,806 Member: 128035 Status: Offline Thanks: 11 Thanked 315 Times in 88 Posts	hi, try enable low level format before content. regards

07-06-2006, 23:30	#4 (permalink)
mccm No Life Poster Join Date: Aug 2005 Posts: 2,351 Member: 173565 Status: Offline Thanks: 158 Thanked 68 Times in 60 Posts	thanks for your reply,as I send to the SC to reload the software cos it was a customised version for specific teco i-mode. We dont have the software out yet,waiting for the solution to decustomise this type of phones,any ideas? Support not seen to be as good as the past,sad.

07-07-2006, 05:58	#5 (permalink)
stefanusrudy No Life Poster Join Date: Mar 2005 Location: S7°1x'xxx" - E112°4x'xxx" Posts: 2,806 Member: 128035 Status: Offline Thanks: 11 Thanked 315 Times in 88 Posts	hi, what was phone original version? (then you flash it with 50616203) if same version, or original version is lower, shouldn't have any problem... but there're so many thing that we don't understand about bb5, i have ever flashed 6680 with same version also dead, flash again didn't help. only higher version can revive it..