C75 testpoint - GSM-Forum

erogsm · 02-06-2006, 23:11

Dear could someone exactly tell me where is stored TP for C75. I open it, so picture regarding TP use 100Ohm(maybe this is a problem because I don't have 10-50Ohm) and see two points one in the near with other. I don't know exactly which one i need to conect via resitor to GND.
I tried both of them but without success. This is my first C75 for unlock, even If I unlocked several C65, with this one have a problem Normal Version 11, have new Papuas, but problem is with TP, I don't see in the pictures right TP, because all of the pictures are the same, and can't see right point on board.
Please does anybody has better picture for TP?
Thanks

erogsm · 02-07-2006, 02:11

Please answer me
Does C75 works with Siemens Eeprom Tool 3.15
I selected
phone=X65 and selected precheck
When I press Init get scanning, and when press red button nothings happend.

Do I need any TP for reading eeprom from C75 with Siemens Eeprom Tool 3.1.5?

Something confused me, because 2 hours before I get connection and save eeprom, but can't be sure that was C75 or my M65.

CAble is good, because with my M65 SET(Siemens eeprom tool) works fine, but with C75 I can't get information after I pressed Init buttom.

Please any sugestion?
Regards

erogsm · 02-07-2006, 13:28

Dear Chris02,
you answered on all message except mine, why?
Please try to solve my problem too
Regards,

electrosoft · 02-07-2006, 13:50

no need resitor connect directly the wire to gnd (for eeprom tool no need test point ) do search before posting newe topic all respances are here
http:///vbb/showthread.php?t=248431

erogsm · 02-07-2006, 15:18

@electrosoft
Thanks a lot friend,
I always made search option for this cases, but even if I opened more then 30 different topics, I can't found right answer.
Problem was because I made eeprom backup with eeprom tool 3.1.5, but now can't get it with the same tool. Problem maybe is because two contacts on the board which were very close eachother I connected, and know
Siemens eeprom tool 3.1.5 with =X65 and precheck enabled doesn't work anymore
What can I do to unlock it, becuase can't contact eeprom tool, that means also can't contact Papuas software to get it work?
Thanks my friend, still one more
Regards

02-06-2006, 23:11	#1 (permalink)
erogsm No Life Poster Join Date: Jul 2001 Location: EU Posts: 567 Member: 5423 Status: Offline Thanks Meter: 10	C75 testpoint Dear could someone exactly tell me where is stored TP for C75. I open it, so picture regarding TP use 100Ohm(maybe this is a problem because I don't have 10-50Ohm) and see two points one in the near with other. I don't know exactly which one i need to conect via resitor to GND. I tried both of them but without success. This is my first C75 for unlock, even If I unlocked several C65, with this one have a problem Normal Version 11, have new Papuas, but problem is with TP, I don't see in the pictures right TP, because all of the pictures are the same, and can't see right point on board. Please does anybody has better picture for TP? Thanks

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
C75 dead after cutting testpoint	colepipo	S-Gold Based Phones	3	10-05-2006 17:56
help in C75 TESTPOINT IS DAMAGED	sofiame2006	S-Gold Based Phones	5	04-20-2006 20:35
Testpoint or No Testpoint ?	khoavtran	FuriouS II	1	10-15-2005 01:22
unlocking newbie [part2]: what cut testpoint does mean? -A65 as MC60 new testpoint-	ciropizza	E-Gold Based Phones	3	07-20-2005 09:31
siemens testpoint,wrong cut repairA60,C60, back testpoint and more	NELIX	Siemens-Benq RingTones and WallPapers	30	06-16-2004 21:15

02-07-2006, 02:11	#2 (permalink)
erogsm No Life Poster Join Date: Jul 2001 Location: EU Posts: 567 Member: 5423 Status: Offline Thanks Meter: 10	Please answer me Does C75 works with Siemens Eeprom Tool 3.15 I selected phone=X65 and selected precheck When I press Init get scanning, and when press red button nothings happend. Do I need any TP for reading eeprom from C75 with Siemens Eeprom Tool 3.1.5? Something confused me, because 2 hours before I get connection and save eeprom, but can't be sure that was C75 or my M65. CAble is good, because with my M65 SET(Siemens eeprom tool) works fine, but with C75 I can't get information after I pressed Init buttom. Please any sugestion? Regards

02-07-2006, 13:28	#3 (permalink)
erogsm No Life Poster Join Date: Jul 2001 Location: EU Posts: 567 Member: 5423 Status: Offline Thanks Meter: 10	Dear Chris02, you answered on all message except mine, why? Please try to solve my problem too Regards,

02-07-2006, 13:50	#4 (permalink)
electrosoft Freak Poster Join Date: Nov 2004 Location: Tunisia Age: 43 Posts: 388 Member: 93850 Status: Offline Thanks Meter: 48	no need resitor connect directly the wire to gnd (for eeprom tool no need test point ) do search before posting newe topic all respances are here http:///vbb/showthread.php?t=248431

02-07-2006, 15:18	#5 (permalink)
erogsm No Life Poster Join Date: Jul 2001 Location: EU Posts: 567 Member: 5423 Status: Offline Thanks Meter: 10	@electrosoft Thanks a lot friend, I always made search option for this cases, but even if I opened more then 30 different topics, I can't found right answer. Problem was because I made eeprom backup with eeprom tool 3.1.5, but now can't get it with the same tool. Problem maybe is because two contacts on the board which were very close eachother I connected, and know Siemens eeprom tool 3.1.5 with =X65 and precheck enabled doesn't work anymore What can I do to unlock it, becuase can't contact eeprom tool, that means also can't contact Papuas software to get it work? Thanks my friend, still one more Regards