CX75 imei 000000000000000, can't turn on! - GSM-Forum

vanhh · 03-04-2007, 09:23

I'm use PapuaUtils read OTP imei is Ok and right but read Imei from fone is 00000000000000, use Freeze to write imei it said "Possible only with "Factory" Security Mode!".
How to fix it, pls? mybe need full flash for it, pls share for me. Thanks!

Gehstock · 03-04-2007, 10:09

On the flash tab
Recalc all keys (Testpoint needed)

Amir-SkillZ · 03-04-2007, 11:11

works for me at cx65 just tested....woks on all 65 75 series ....thankx

vanhh · 03-05-2007, 11:19

Thanks for Ur help!
when read Imei from phone is info(Don't TP):
Getting Information:
Model: SIEMENS CX75 23 lg7
Phone is in "Format FFS?" mode
IMEI: 000000000000000
SecurityStatus: CustomerMode
HWID: 5000
Accumulator Voltage: 3935 mV.

when read code(Don't TP)
Getting the codes from phone...
Phone was turned off by mistake:
EXIT: 0004:9126
FILE:
sddsacc_power
CPSR: A0000010
CepId: 3600
ExitString:
Receive Message

Use TP(dio.) Recall Keys it said:

Checking value of SKEY from page "Codes"...
Invalid SKEY !

How to do, pls? thankx!

ra1ex · 03-05-2007, 15:04

Quote:

Originally Posted by vanhh

Phone is in "Format FFS?" mode
IMEI: 000000000000000

FFS_C is formatted. Phone need to swup a file XFS or backup filesystem from other phone.

Quote:

Checking value of SKEY from page "Codes"...
Invalid SKEY !

Enter 12345678 or other in the Skey field on page Codes

vanhh · 03-11-2007, 08:36

Quote:

Originally Posted by ra1ex

Enter 12345678 or other in the Skey field on page Codes

Thanks, But it is still(can not turn on)

Checking value of SKEY from page "Codes"...
Used SKEY: 12345678
Auto Ignition...
Transfer boot...
BOOT is loaded...
Pause 2 sec...
Getting Information...
FlashID: 0089,880D
CX75 SIEMENS 35642xxxxxxxxx
HASH: 53A075CF34B16FA0535A333865BE27A2
OTP ESN: C5CAB327
OTP IMEI: 35642xxxxxxxxxxx
Error (55464545): Incorrect call!
Total EEP blocks: 233
Blocks 52,76,5008,5009,5077,5121,5122,5123 found.
Old block 5008 saved in 356429xxxxxxxxxxxxx_EEP_070312015052_5008
Block 5008 replaced.
Old block 5077 saved in 356429xxxxxxxxxx_EEP_070312015052_5077
Block 5077 replaced.
Block 5009 does not require replacement!
Old block 5121 saved in 356429xxxxxxxxxx_EEP_070312015052_5121
Block 5121 replaced.
New Master codes:
*#0000*12345678#
*#0001*12345678#
*#0002*12345678#
*#0003*12345678#
*#0004*12345678#
*#0005*12345678#
Old block 5122 saved in 356429xxxxxxxxxxxxx_EEP_070312015052_5122
Block 5122 replaced.
Old block 5123 saved in 356429xxxxxxxxxxx_EEP_070312015052_5123
Block 5123 replaced.
Old block 52 saved in 356429xxxxxxxxxxxx_EEP_070312015052_52
Block 52 replaced.
Block 76 does not require replacement!
Working with BCORE...
BCORE IMEI does not require change!
Reading segment BCORE...
Segment BCORE is stored in C5CAB327_A0000000_BCORE_070312015058.bin
New HASH written in BCORE.
Boot released. Everything is closed.

Quote:

Originally Posted by ra1ex

FFS_C is formatted. Phone need to swup a file XFS or backup filesystem from other phone.

How to write XFS file on it(i have CX75_2_ru-RussianRetail_23_0001.xfs)

Thankx!

ra1ex · 03-11-2007, 10:14

Use WinSwup with Options->Update-Concept->Force BSL and Check Box "Pre-Check Skip". Phone should be switched off. Tab START in WinSwap and push Red Button on the phone shortly. BUT the firmware in phone too should be 23 versions as well as XFS!!!

03-04-2007, 09:23	#1 (permalink)
vanhh No Life Poster Join Date: Jul 2004 Posts: 504 Member: 71603 Status: Offline Thanks Meter: 31	CX75 imei 000000000000000, can't turn on! I'm use PapuaUtils read OTP imei is Ok and right but read Imei from fone is 00000000000000, use Freeze to write imei it said "Possible only with "Factory" Security Mode!". How to fix it, pls? mybe need full flash for it, pls share for me. Thanks!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
8310 flash OK, once turn off, can't turn-on again!	kennyli	Nokia Hardware & Hardware Repair	17	04-02-2004 11:58
3410 can't turn on,but it turn on when I put battery inside ???	DaliborDu	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	10-22-2003 01:33
sgh a800 can't turn on	Destructor	VLSI, Conexant, Skyworks and Old Models	4	09-08-2003 12:22
3310 i can flash but i can't turn ON	Monty	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	9	12-10-2002 19:14
Siemens S25 Can't turn on	jivkobg	Siemens Hardware Repair Area	4	07-23-2002 18:34

03-04-2007, 10:09	#2 (permalink)
Gehstock Freak Poster Join Date: Jul 2005 Age: 46 Posts: 366 Member: 163721 Status: Offline Thanks Meter: 148	On the flash tab Recalc all keys (Testpoint needed)

03-04-2007, 11:11	#3 (permalink)
Amir-SkillZ No Life Poster Join Date: Nov 2004 Location: Capetown Posts: 6,709 Member: 91045 Status: Offline Thanks Meter: 8,696	works for me at cx65 just tested....woks on all 65 75 series ....thankx

03-05-2007, 11:19	#4 (permalink)
vanhh No Life Poster Join Date: Jul 2004 Posts: 504 Member: 71603 Status: Offline Thanks Meter: 31	Thanks for Ur help! when read Imei from phone is info(Don't TP): Getting Information: Model: SIEMENS CX75 23 lg7 Phone is in "Format FFS?" mode IMEI: 000000000000000 SecurityStatus: CustomerMode HWID: 5000 Accumulator Voltage: 3935 mV. when read code(Don't TP) Getting the codes from phone... Phone was turned off by mistake: EXIT: 0004:9126 FILE: sddsacc_power CPSR: A0000010 CepId: 3600 ExitString: Receive Message Use TP(dio.) Recall Keys it said: Checking value of SKEY from page "Codes"... Invalid SKEY ! How to do, pls? thankx!

03-11-2007, 10:14	#7 (permalink)
ra1ex Junior Member Join Date: Sep 2006 Posts: 15 Member: 358342 Status: Offline Thanks Meter: 0	Use WinSwup with Options->Update-Concept->Force BSL and Check Box "Pre-Check Skip". Phone should be switched off. Tab START in WinSwap and push Red Button on the phone shortly. BUT the firmware in phone too should be 23 versions as well as XFS!!!