Repair SL75 Eeprom - GSM-Forum

warmsteel · 12-06-2006, 13:14

I have a SL75 that has a problem with the Eeprom that I would like to fix! The problem occurred when I was attempting a full flash with VKlay when the connection was broken, now all the phone does is beep when the power switch is pressed. Some research in the forums has suggested that the Eeprom is damaged? I have attempted a repair with Siemens EEPROM tool V3.15 however all I get is an error message that some blocks were not written to the phone, leaving me with the same problem.
Any advice and suggestions are most welcome.
Thank you

warmsteel · 12-12-2006, 11:25

Surely there must be someone who can help? All these views and no replies, come on guys help me out a little!

Cryspim · 12-14-2006, 20:47

Sl75 hardware ID 017E...new phones. No solution at this moment. bootcore area damaged. i have the same problem with a brand new phone fu**ed by martech, and waiting for solution.

Cryspim

dnteam · 12-15-2006, 08:09

well i have try also and i even have and bootloader from them
i just need some software to use it whit

warmsteel · 12-16-2006, 19:39

Using EEPROM tool, I have managed to make a copy of the EEPROM/BOOTCORE file but when I try to load it into my phone I keep getting and unable to load messages for different blocks, 5005, 5007, 5008 and 5009 but to mention just a few? How does Siemens load the files? I would imagine that there must be a way of installing these files?

dnteam · 12-17-2006, 10:47

there is but u need tools from siemens to do that and what u need is a bootadapter made bye siemens 2002
and then the hardest part the software to use the bootadapter

warmsteel · 12-21-2006, 12:03

What kind of software are we talking about? Is it readily available? If it is not, where does this leave us? Are we stuck?

12-06-2006, 13:14	#1 (permalink)
warmsteel Junior Member Join Date: May 2006 Posts: 17 Member: 284464 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	Repair SL75 Eeprom I have a SL75 that has a problem with the Eeprom that I would like to fix! The problem occurred when I was attempting a full flash with VKlay when the connection was broken, now all the phone does is beep when the power switch is pressed. Some research in the forums has suggested that the Eeprom is damaged? I have attempted a repair with Siemens EEPROM tool V3.15 however all I get is an error message that some blocks were not written to the phone, leaving me with the same problem. Any advice and suggestions are most welcome. Thank you

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
Repair SL75 AMD CHIP STEP BY STEP	sidcell	DreamBox	1	08-13-2007 07:52
Repair damaged EEPROM and 4 Locks closed in NOKIA	Freestyler2000	Main Sales Section	0	01-11-2002 18:57
Repair of EEPROM with 4 locks closed in NOKIA	Freestyler2000	Main Sales Section	16	01-05-2002 02:15
Could sb help me repairing this EEPROM checksums of 3330 ??	majid	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	9	12-10-2001 03:21
i need 922FT4,1 E backup to repair PB3 eeprom plzz	makona	Infineon C16X M51 & ARM7 M52 BASED	8	04-05-2001 07:51

12-12-2006, 11:25	#2 (permalink)
warmsteel Junior Member Join Date: May 2006 Posts: 17 Member: 284464 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	Surely there must be someone who can help? All these views and no replies, come on guys help me out a little!

12-14-2006, 20:47	#3 (permalink)
Cryspim Freak Poster Join Date: Apr 2004 Location: Made In Brazil Posts: 447 Member: 62561 Status: Offline Thanks: 7 Thanked 704 Times in 70 Posts	Sl75 hardware ID 017E...new phones. No solution at this moment. bootcore area damaged. i have the same problem with a brand new phone fu**ed by martech, and waiting for solution. Cryspim

12-15-2006, 08:09	#4 (permalink)
dnteam Junior Member Join Date: Dec 2006 Posts: 22 Member: 407788 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	well i have try also and i even have and bootloader from them i just need some software to use it whit

12-16-2006, 19:39	#5 (permalink)
warmsteel Junior Member Join Date: May 2006 Posts: 17 Member: 284464 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	Using EEPROM tool, I have managed to make a copy of the EEPROM/BOOTCORE file but when I try to load it into my phone I keep getting and unable to load messages for different blocks, 5005, 5007, 5008 and 5009 but to mention just a few? How does Siemens load the files? I would imagine that there must be a way of installing these files?

12-17-2006, 10:47	#6 (permalink)
dnteam Junior Member Join Date: Dec 2006 Posts: 22 Member: 407788 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	there is but u need tools from siemens to do that and what u need is a bootadapter made bye siemens 2002 and then the hardest part the software to use the bootadapter

12-21-2006, 12:03	#7 (permalink)
warmsteel Junior Member Join Date: May 2006 Posts: 17 Member: 284464 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	What kind of software are we talking about? Is it readily available? If it is not, where does this leave us? Are we stuck?