GSM Shop GSM Shop
GSM-Forum  

Welcome to the GSM-Forum forums.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features.
Only registered members may post questions, contact other members or search our database of over 8 million posts.

Registration is fast, simple and absolutely free so please - Click to REGISTER!

If you have any problems with the registration process or your account login, please contact contact us .

Go Back   GSM-Forum > GSM & CDMA Phones / Tablets Software & Hardware Area > Samsung > QUALCOMM Models (3G)

QUALCOMM Models (3G) SGH-Z105x, SGH-Z107x, Z110, Z130, Z140, Z300, Z320i, Z500, Z510, ZM60, ZV10, ZV30, ZX10.

Reply
 
LinkBack Thread Tools Display Modes
Old 04-24-2006, 21:48   #1 (permalink)
Freak Poster
 
Join Date: Dec 2002
Age: 48
Posts: 203
Member: 18938
Status: Offline
Thanks Meter: 3
Multiloader No phone is connected


Hi I have a big problem:

One zv10 was freezed because of incorrect codes inserting more than 3 times.
I tried to flash it with usb+com cable. First I started the download mode in phone(key9 + power on), and after selected all flashes on multiloader.
The phone was well detected, and started to flash, but stopped at 49%
The error it gave was: "RX no response"
Now phone powers just for 2 seconds and switch off again(I can just see samsung logo).

I´m trying to flash it again: I put the phone in flash mode( I can read on small screen "DOWNLOAD"), the computer recognizes the samsung modem on com3, but when I click download on program it doesn´t do it. And if I click Port search, it tells "No phone is connected". Any solution pls? I have read a lot of posts, but cant get the solution if there is any

tx in advance
david
  Reply With Quote
Old 04-25-2006, 00:28   #2 (permalink)
Freak Poster
 
Join Date: Dec 2002
Age: 48
Posts: 203
Member: 18938
Status: Offline
Thanks Meter: 3
ohh...now I finally could flash it 100%, but phone still swichts on and off again..... lets try to flash it again and see ...
  Reply With Quote
Old 04-25-2006, 01:04   #3 (permalink)
Freak Poster
 
Join Date: Dec 2002
Age: 48
Posts: 203
Member: 18938
Status: Offline
Thanks Meter: 3
this is my result after flashing with multiloader 1.01:
Modem Code Download
------------------
ÆÐŶ ÀçÀü¼ÛÇÕ´Ï´Ù.
Flash erase Áß.. Àá½Ã¸¸ ±â´Ù¸®¼¼¿ä
Flash Programming Áß
Flash finalizing and verifying...
SHP Rsrc1 Download
----------------------
Flash erase Áß.. Àá½Ã¸¸ ±â´Ù¸®¼¼¿ä
Flash Programming Áß
SHP Rsrc2 Download
----------------------
Flash erase Áß.. Àá½Ã¸¸ ±â´Ù¸®¼¼¿ä
Flash Programming Áß
SHP FS Download
------------------
Flash erase Áß.. Àá½Ã¸¸ ±â´Ù¸®¼¼¿ä
Flash Programming Áß
ÆÐŶ ÀçÀü¼ÛÇÕ´Ï´Ù.

Now phone switchs on but, screen is always red colour:
when I tried to unlock it with winimei in the screen of the phone appeared:
error: fatal,.... press and hold * to reset and log
after 3 seconds: "press # to dmode"....

anyone knows what can I do??!!

i´ll really appreciate it
tx
  Reply With Quote
Old 04-26-2006, 00:34   #4 (permalink)
Freak Poster
 
Join Date: Dec 2002
Age: 48
Posts: 203
Member: 18938
Status: Offline
Thanks Meter: 3
no any help? I have read entire forum but havent found solution for this...
pls help!!
  Reply With Quote
Old 04-26-2006, 00:51   #5 (permalink)
Freak Poster
 
Join Date: Aug 2004
Location: OZ
Age: 49
Posts: 289
Member: 79390
Status: Offline
Thanks Meter: 29
follow these steps and should be ok..

The following information is for reference only.

1. Download multi-downloader (UMdloader V1.4).
2. Download the MDL.dll & unzip to same directory
3. Download software of appropriate carrier (again, appropriate carrier) & unzip
4. Install USB driver. You can use the USB driver for CDMA phones, e.g. A601, N361 & etc – attached.

Before you can flash, you need an USB data cable and setup the USB connection, using the attached USB driver. If you have installed this USB driver before, please ignore and you do not connect the phone at this time.

For USB driver installation – NOTE: Do not connect phone before USB driver installation!!!!!!!!!
- Install the USB driver
- Connect the phone
- All PC to select driver. You will be warned that something do not pass the window log test, you will click ‘Continue anyway’. This will appear 2 or 3 times.


(PS: The USB cable that comes in the Sales package is fully compatible to E720, S342i & etc.)

Power on the phone and connect it to computer. The computer will install the connection and you will see a new modem – check this out from
‘Control Panel->Phone & Modem Options’->’Modems’

If you find a ‘SAMSUNG CDMA Modem’ appeared and attached to a port. Otherwise, please check the installation procedure again. The Multi-downloader will use this port to flash. Power off the phone.

Now, open UMdloader 1.4 and enter the following information to multi-downloader (I choose Telstra for example).

Boot loader: Do not use
USB Boot: Do not use
MODEM Code: TMQZS
Rsrc: Rsrc_Z500_Telstra
Rsrc2: Rsrc2_Low
Factory Fs: FactoryFs_Z500_Telstra


On SGH-Z500 (make sure the phone is OFF), Press 9+END keys (white screen will display)
Then, connect the phone to the data cable.
Click ‘Apply configuration’ -> you will see the COM port will appear in the top half section of the downloader.
Click ‘Go X’ àX is the port number OR click ‘Download All’ to flash.

This multi-downloader supports 8 flashing concurrently.

Hope that helped..
  Reply With Quote
Old 04-29-2006, 00:32   #6 (permalink)
Freak Poster
 
Join Date: Dec 2002
Age: 48
Posts: 203
Member: 18938
Status: Offline
Thanks Meter: 3
Exclamation

I downloaded 1.4 from one web page and didn´t work. Also 1.1 from rapidshare link on this topic:
Unlocking ZV10BUFA2 fimware version(http://forum.gsmhosting.com/vbb/show...275952&page=4).

can u give give me the link where you downloaded the whole pack?
  Reply With Quote
Old 04-30-2006, 14:14   #7 (permalink)
Freak Poster
 
Join Date: Dec 2002
Age: 48
Posts: 203
Member: 18938
Status: Offline
Thanks Meter: 3
Ok Worked!!

I used multiloader 1.01 and flash: http://www.rexnet.it/firmware.../zv10buek1.zip (tx taorik.om!!).

best regards,
david
  Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
thread Thread Starter Forum Replies Last Post
Multiloader Not Recognising USB Connection Altad BlackBerry (RIM) 5 03-29-2009 12:47
mfi multiloader no mml mirumo BlackBerry (RIM) 1 01-15-2009 05:34
No phones connect!! gtifreeek UFS2 + UFS3-Tornadoflasher 2 08-03-2007 22:41
I Have T100 Every Thing Is Working But Phone Is Not Connecting Call OSSIE VLSI, Conexant, Skyworks and Old Models 3 05-16-2003 19:52
N3310, vibra & LEDs are on when connect battery, but phone is dead MaRiN Nokia Hardware & Hardware Repair 8 02-20-2003 02:32

 



All times are GMT +1. The time now is 05:09.



Powered by Searchlight © 2024 Axivo Inc.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2023 -
Page generated in 0.19822 seconds with 9 queries

SEO by vBSEO