V3i Dead after PDS Repair - GSM-Forum

PIMP123 · 08-16-2006, 20:58

This phone was unlocked OK (TP was not damaged, bcos I drilled a hole on top od shield, and 100000000% no contact with phone PCB)
But phone restarts when accessing network if phone is open.
So I decided to do PDS repair.
But immediately after doing this, phone is dead: ONLY the green charging light shows permanently when I put battery.
Worst still, when I connect cable, PC shows unknown usb device.
Also with TP, phone cant enter Blank again.

How can I resolve this
(BTW, I did not use the newest version of p2k (I think the last 3 updates i dont have)

**viru** · 08-16-2006, 22:14

Chk the test point resistor u might have damaged it

B.R
Viru

PIMP123 · 08-17-2006, 12:42

But as I said, the hardware is 100% sure OK.
Make a search with this topic, and you will see others too have same problem, but non stated how to solve it.
Its surely a software problem, but how to resolve it is a problem now.

B4 I did PDS repair I must use TP to get it into Blank mode, and until that, phone went into blank mode 1st attemp.
Immediately after PDS repair says phone is repaired OK, then phone could not power anylonger.

Thanks though, but I still need help

the real bender · 08-18-2006, 08:00

Quote:

Originally Posted by PIMP123

But as I said, the hardware is 100% sure OK.
Make a search with this topic, and you will see others too have same problem, but non stated how to solve it.
Its surely a software problem, but how to resolve it is a problem now.

B4 I did PDS repair I must use TP to get it into Blank mode, and until that, phone went into blank mode 1st attemp.
Immediately after PDS repair says phone is repaired OK, then phone could not power anylonger.

Thanks though, but I still need help

It is not solved yet. V3i pds repair for p2k tool 4.1 - 5.3 do not work. Do not use V3i pds repair with p2k tool.

gyuszko · 08-18-2006, 10:06

it must enter in blank flash mode with TP if no HW damage, even if flash IC is empty!

08-16-2006, 20:58	#1 (permalink)
PIMP123 Freak Poster Join Date: Nov 2005 Posts: 244 Member: 196467 Status: Offline Thanks: 0 Thanked 13 Times in 7 Posts	V3i Dead after PDS Repair This phone was unlocked OK (TP was not damaged, bcos I drilled a hole on top od shield, and 100000000% no contact with phone PCB) But phone restarts when accessing network if phone is open. So I decided to do PDS repair. But immediately after doing this, phone is dead: ONLY the green charging light shows permanently when I put battery. Worst still, when I connect cable, PC shows unknown usb device. Also with TP, phone cant enter Blank again. How can I resolve this (BTW, I did not use the newest version of p2k (I think the last 3 updates i dont have)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
V3i DEAD AFTER REPAIR PDS	hummy	P2k Series	14	07-08-2007 12:09
Dead V360 after PDS repair	mihaser	P2k Series	3	10-01-2006 10:15
Dead V360 after PDS repair	mihaser	Smart-Clip	6	09-28-2006 15:33
V3i Dead After Flash And Reapir Pds " Plz Help Mr Zula"	amiriratel	Motorola P2K (USB-Smart)	1	06-14-2006 18:22
v3i dont cant go to flash mode after pds repair	btl	Smart-Clip	0	04-02-2006 14:53

08-16-2006, 22:14	#2 (permalink)
viru Product Manager Join Date: Jan 2006 Location: 亚洲 / Asia Age: 25 Posts: 10,565 Member: 222198 Status: Offline Sonork: 100.102981 Thanks: 301 Thanked 3,771 Times in 717 Posts	Chk the test point resistor u might have damaged it B.R Viru

08-17-2006, 12:42	#3 (permalink)
PIMP123 Freak Poster Join Date: Nov 2005 Posts: 244 Member: 196467 Status: Offline Thanks: 0 Thanked 13 Times in 7 Posts	But as I said, the hardware is 100% sure OK. Make a search with this topic, and you will see others too have same problem, but non stated how to solve it. Its surely a software problem, but how to resolve it is a problem now. B4 I did PDS repair I must use TP to get it into Blank mode, and until that, phone went into blank mode 1st attemp. Immediately after PDS repair says phone is repaired OK, then phone could not power anylonger. Thanks though, but I still need help

08-18-2006, 10:06	#5 (permalink)
gyuszko Product Supporter Join Date: Dec 2001 Location: in my skin Age: 36 Posts: 1,229 Member: 8086 Status: Offline Thanks: 30 Thanked 180 Times in 64 Posts	it must enter in blank flash mode with TP if no HW damage, even if flash IC is empty!