Tiger - Clip Philips 330 hang on TAT Mode
 

hello,

Tiger - Clip hang on TAT mode 4 unlocking philips 330

this steps i do

turn tiger-clip on (use external power 9v 500mAh)
cable in phone (GPG003 - PH820) and in Clip (RJ 45)
select Model - NEW-EXT?
clip LCD "POWER ON Phone"
1x short press power button on phone
Phone LCD " TAT MODE"
Clip LCD "Entering TAT Mode"

that all - no change in CLIP - LCD

what happends? any idear?

best regards

read the manual
www.c4-pack.com

in phillips NEVER put off the battery when phone is en tat mode...
always power off with on/off buttom
BR

hello,

i read the manual

mobile enters to TAT mode and thats all


maybe this phone not supported ?


best regards

phone is suported but i think you need make small modification on your clip.

http://www.tiger-clip.com/images/products/home.jpg

Look your clip and tell me if you see the logo like this below the screen.

I wait your reply to tell u what to do.

BR.
Steve.

hi Steve

the same was on my clip when power on, this messages show

1
Tiger clip power
ed by Furious

2
Team, engineered
by gsmVolume

3
http://www.tiger
-clip.com

4
Version
06-02-02



best regards

Im talking about the Tiger Clip logo in red not about the screen.
Just tell me if you have this logo like this or no below the screen.

Br.
Steve.

oh - sorry

on my clip, the metal under the screen is blank, no tiger-clip-logo.




best regards

please visit the support web of the clip... and read the first on your left up.....
you need to do hard modification...


Hardware modificationhttp://www.tiger-clip.com/images/spacer.gifhttp://www.tiger-clip.com/images/spacer.gif If you buy TIGER-CLIP before 8 february please check support area you have to do a small modification on pcb. Start today if you buy TIGER-CLIP from us you wont need to modify anything. You will receive clip fully tested and working. BR. Steve.


BR

thx

i will do it - i post the results of it works or not


BR

hm - the clip has not the same layout --

+---TC1602A------1-2-3-4-5-6--b-b-b-b-7-8-9-10-11-12---+

b=blank

witch line (7-12) must cut ? Line number 9 ???

ok i cut number 11 and make the modify - but the same problem again,

phone in TAT-mode ---- tiger-clip display hang in -- entering TAT mode

what can i do now ?

phone-model = 996140003559 ct3308
cn = HI140433H01872
PN = E0350432
made in france

no sim in phone
cable type is GPG003 - PH820 ( was include by the tiger-clip )
i opend the cable and saw that no 1,5kOhm inside - only 3 cabel
black to pin 1, white to pin 3 and blue to pin 4,

like this
++++++++++++++++++++++
+ B------B--B--blue--B---bl+
+B------B--B--B-Wh-B-----+
++++++++++++++++++++++
B = blank
bl = black (pin 12 grd)
W =white (pin 9 Tx)
blue = blue (pin 8 Rx)

RJ45
................xxxxxxx....................
++++++++++++++++++++++++++
+B--blue--white--B--B--B--B--bl.+
++++++++++++++++++++++++++
front view
B = blank
blue = blue (pin 2)
bl. = black (pin 8)
white = white (pin3)

the R1,5kOm must plase where ? (who is the +5v line ? box? or external?)



BR

Hello Furious-Team

where are you ??

im here. Please read what follow.

You have 1st stock of tiger clip and we made small mistake on pcb assembling.

Please look here :

http://www.tiger-clip.com/guru1/cliprepair.jpg

you must do like this and will works 200%

let me know.

BR.
Steve.

you see this picture

that the modify i make

and it do´nt solve the problem.

i saw on the pinout picture (on tiger-clip support-side) that the philips 330 cable have a R1,5kOm ,
my cable did´nt have a R1,5kOhm -- is that ok ?



BR

u didn't modify like my picture. Look better u need to add resistor like on my picture. Exist 3 pcb version of tiger clip and 2 modifications. As you told me you do not have the tiger clip logo below the LCD screen mean you have the 1st version of pcb so you have to do this one like on my picture. Beleve me do this will works 100% ;)

BR.
Steve.

u made modification for the 2nd version but you have the 1st one.