problems connecting phones to smti - GSM-Forum

$ide$tep · 09-08-2011, 11:00

i have some phones to unlock-change language. when i press detect phone, info reads ok:

Found Phone, Phone Info:
- Phone Type :myV-55
- Phone FW :KB3,MR: 101204 0931
- Phone HT :22 00 00
- Phone IMEI :355417001954376
- Phone Code :00000000 (inactive)
- Prod. Code :251545034
- Board Type :m62+

- NOR Flash ID :0001 227E 2212 2200
- Chip [0] :AMD 29LV128BM 128Mbit

- Use Ufl with FID12!

Boot Method: "GP Device" Autodetect

Operation Cost:
- Clear/Set Net Code :FREE
- Change Firmware :FREE

P.S. GP Method Work Only USE "SMTi Virtual Port(COM0)"
HS Method Clear User Code 1 Credit

but code reading, flashing does not work. phones are brand new. i tried to use jigs and solder wires to mainboard, nothing helps. error is always the same:
Look For Target ...Not Found!
- MSG: CHECK TP!

how to solve that? if i make hw modification with zener diode as shown in sticky topic, will it help? few month ago i flashed some phones and it was ok

$ide$tep · 09-08-2011, 13:16

try to flash myx-6 using jig:

Look For Target ...Found!
- Target IDCODE: 3100E02F
Stopping Target ...Success!
after that nothing happens. buttons become active and i can press flash again, but phone wont be detected until i reconnect battery. press flash again, again it shows
Look For Target ...Found!
- Target IDCODE: 3100E02F
Stopping Target ...Success!
and nothing. what happened with my box?

09-08-2011, 11:00	#1 (permalink)
$ide$tep Freak Poster Join Date: Oct 2004 Location: Kiev, Ukraine Age: 39 Posts: 119 Member: 88304 Status: Offline Thanks Meter: 9	problems connecting phones to smti i have some phones to unlock-change language. when i press detect phone, info reads ok: Found Phone, Phone Info: - Phone Type :myV-55 - Phone FW :KB3,MR: 101204 0931 - Phone HT :22 00 00 - Phone IMEI :355417001954376 - Phone Code :00000000 (inactive) - Prod. Code :251545034 - Board Type :m62+ - NOR Flash ID :0001 227E 2212 2200 - Chip [0] :AMD 29LV128BM 128Mbit - Use Ufl with FID12! Boot Method: "GP Device" Autodetect Operation Cost: - Clear/Set Net Code :FREE - Change Firmware :FREE P.S. GP Method Work Only USE "SMTi Virtual Port(COM0)" HS Method Clear User Code 1 Credit but code reading, flashing does not work. phones are brand new. i tried to use jigs and solder wires to mainboard, nothing helps. error is always the same: Look For Target ...Not Found! - MSG: CHECK TP! how to solve that? if i make hw modification with zener diode as shown in sticky topic, will it help? few month ago i flashed some phones and it was ok

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
news headlines to gsm phone	mos	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	7	05-22-2016 11:42
How to add a language in 51xx/61xx	tati	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	05-21-2013 19:20
How to upload a new firmware...	Brand	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	06-08-2012 18:29
Copy from one 6110 to another	Leif Nielsen	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	06-10-1999 22:36

09-08-2011, 13:16	#2 (permalink)
$ide$tep Freak Poster Join Date: Oct 2004 Location: Kiev, Ukraine Age: 39 Posts: 119 Member: 88304 Status: Offline Thanks Meter: 9	try to flash myx-6 using jig: Look For Target ...Found! - Target IDCODE: 3100E02F Stopping Target ...Success! after that nothing happens. buttons become active and i can press flash again, but phone wont be detected until i reconnect battery. press flash again, again it shows Look For Target ...Found! - Target IDCODE: 3100E02F Stopping Target ...Success! and nothing. what happened with my box?