dead gd 67 - GSM-Forum

terminaseb · 06-29-2004, 15:36

I have just killed my gd67 using free unlocker. i used GD67 V1.0. loaded data file GD67Fc.plc, flashed the phone up to 100%. phone says CRC complete then switches off. i press SP-Unlock but programm says test mode fail. tried again...& again...both spunlock & flashing again...but still nothing. the battery was fully charged. .I have tried winmodo solution for gd67 fix A29 but still samething..If anybody have a solution please send it to me .
Regards.

eddiesoft · 06-29-2004, 15:44

test to flash with new winmodo. if problem... only jtag!!!

EDDIESoft

SaryK · 06-29-2004, 21:53

-Rename gd67sp.spu to PA13.bin
-Run ghost3D and select GD30
-press partial flash and select PA13,press and hold power buton
-when is finished you will see on LCD test mode and disconect
your phone,phone must be in test mode
-now rename PA13 to gd67sp.spu and run panasonic-gd67 and
conect phone
-load gd67sp.spu and press flash
-after flashing press unlock
-now your phone is live

Tested 100% with GD67 killed by free unlocker

eddiesoft · 06-30-2004, 09:06

if comunication phone<>computer is good - no problem, but if not comunication... only jtag

EDDIESoft

gabila · 03-18-2005, 23:40

i have jtag schematics... but what sw to use with jtag?
and how to get the bootzone? (from where)
i need this for gd 92

06-29-2004, 15:36	#1 (permalink)
terminaseb Junior Member Join Date: May 2004 Age: 56 Posts: 3 Member: 65989 Status: Offline Thanks Meter: 0	dead gd 67 I have just killed my gd67 using free unlocker. i used GD67 V1.0. loaded data file GD67Fc.plc, flashed the phone up to 100%. phone says CRC complete then switches off. i press SP-Unlock but programm says test mode fail. tried again...& again...both spunlock & flashing again...but still nothing. the battery was fully charged. .I have tried winmodo solution for gd67 fix A29 but still samething..If anybody have a solution please send it to me . Regards.

03-18-2005, 23:40	#5 (permalink)
gabila Junior Member Join Date: Apr 2003 Location: TM romania Age: 46 Posts: 26 Member: 26739 Status: Offline Thanks Meter: 0	what sw to use with jtag? i have jtag schematics... but what sw to use with jtag? and how to get the bootzone? (from where) i need this for gd 92

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
GD 67 dead	Tomáš Nejedlý	Panasonic	3	01-12-2004 23:49
GD 67 DEAD after unlocking with SPunlock soft	kone	Panasonic	13	08-03-2003 15:01
GD 67 dead	CezaricaGSM	Panasonic	4	06-24-2003 10:00
Nobody Unlock GD 67???	CoolWire	Panasonic	0	09-29-2002 18:13
Software for Panasonic GD 67	Scorpic	Panasonic	3	09-27-2002 10:52

06-29-2004, 15:44	#2 (permalink)
eddiesoft Freak Poster Join Date: Feb 2002 Location: Bulgaria,Pleven Age: 55 Posts: 346 Member: 9269 Status: Offline Thanks Meter: 2	test to flash with new winmodo. if problem... only jtag!!! EDDIESoft

06-29-2004, 21:53	#3 (permalink)
SaryK Freak Poster Join Date: May 2001 Location: CZ Age: 48 Posts: 236 Member: 4505 Status: Offline Thanks Meter: 4	-Rename gd67sp.spu to PA13.bin -Run ghost3D and select GD30 -press partial flash and select PA13,press and hold power buton -when is finished you will see on LCD test mode and disconect your phone,phone must be in test mode -now rename PA13 to gd67sp.spu and run panasonic-gd67 and conect phone -load gd67sp.spu and press flash -after flashing press unlock -now your phone is live Tested 100% with GD67 killed by free unlocker

06-30-2004, 09:06	#4 (permalink)
eddiesoft Freak Poster Join Date: Feb 2002 Location: Bulgaria,Pleven Age: 55 Posts: 346 Member: 9269 Status: Offline Thanks Meter: 2	if comunication phone<>computer is good - no problem, but if not comunication... only jtag EDDIESoft