Can't calibrate touch screen on Alfatel H1 - GSM-Forum

amol_sm · 05-25-2009, 16:49

Hello to all,

I have one phone H1 in my hand phone is working fine. But i can't calibrate the touch screen Here is the Log of calibration.

Code:

COM5 [VCP1] selected
module  v2.82
Action: touchscreen calibration
mode: 1
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:3503:000D
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
warning: can't read software version, probably unknown firmware
detecting structure #2...
 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18warning: wrong packet cs
 19 20 21 22 23 24 25 26 27warning: wrong packet cs
 28 29error: detection failed (30 tries), read flash and send to support
connection lost
error: operation failed !
Finished, time used: 10 sec
Remove/Install battery now !

Also i try with Reverse calibration too but same error show
Anyone know how to solve this problem !!!!!

Thankx in advance.

InfinityHelp · 05-26-2009, 23:45

hello!

what do you use as interface?

amol_sm · 05-28-2009, 07:47

I use Infinity as Interface.
Spider Couldn't find this set pin out.
That's why i open the set & use Rx-Tx-Gnd point for connect the phone.

InfinityHelp · 05-31-2009, 22:04

hello!

make format FFS comlete
power on phone, wait 30 sec
power off phone
repeat calibration again
please note that you must try all calibration methods
if will not work- post here all logs, we will check them all and if needed i will request full flash for processing

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Can't calibrate touch sceen of Alfatel H1	amol_sm	Infinity-Box	6	03-24-2009 16:10
N82 CRAZY problem in calibration touch screen	MDK23	Infinity-Box	3	01-08-2009 02:43
N82 problem in calibration touch screen	MDK23	Infinity-Box	1	01-07-2009 21:43
i750 can't calibrate touch screen.....	aikonmani	Samsung Hardware Repair	2	11-25-2008 17:45
unable to calibrate touch screen	jbbasha	Infinity-Box	10	09-12-2008 14:23

05-26-2009, 23:45	#2 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! what do you use as interface?

05-28-2009, 07:47	#3 (permalink)
amol_sm No Life Poster Join Date: Sep 2006 Posts: 2,929 Member: 343326 Status: Offline Thanks Meter: 1,463	I use Infinity as Interface. Spider Couldn't find this set pin out. That's why i open the set & use Rx-Tx-Gnd point for connect the phone.

05-31-2009, 22:04	#4 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! make format FFS comlete power on phone, wait 30 sec power off phone repeat calibration again please note that you must try all calibration methods if will not work- post here all logs, we will check them all and if needed i will request full flash for processing