n8 mtk6235 read errror - GSM-Forum

anil_prajapati · 04-18-2011, 16:08

Code:

COM28 [VCP0] selected
module  v3.29
Device: Autodetect 6205-6239 NOR
Checking data, wait...
advanced flash detection enabled
Action: read flash
====>  Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6235:8B00:8A01]...
CPU: MT6235
high speed boot On
chip: 0000:0000:0003
status: FF
boot packet size: 0400
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 11 sec
Remove/Install battery now !

anil_prajapati · 04-18-2011, 16:11

Code:

Action: read/check information
Model: Autodetect 6205-6239 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
Hardware version: MT6235B, E0
Hardware version: MTK35_09A_GEMINI_HW
Software version: TDCN8S_V2.1_19_512_0
Software date: 2000.00.00
Barcode: 1202011                                                     10
imei-1: 3
Finished, time used: 8 sec
Remove/Install battery now !

anil_prajapati · 04-18-2011, 16:24

Code:

COM28 [VCP0] selected
module  v3.82
Device: Micromax-Q5
Checking data, wait...
Action: read flash NAND
interface: BROM_DLL_v3.1016.00
Connect...
Phone should be Switched OFF !
Press and HOLD Power button now !
Connecting...
Booting...
Release Power button now !
bootcode current/expected: 3.2/3.2
CPU: 6235:8B00:8A00
status: FF
bbchip bl ver: FE
NOR flash chip: not installed
NAND flash id[001E]: 0020:007600200076 [ST] ST512W3A
chip size: 64Mb
page/spare size: 0200/0010
pages per block: 0020
bits i/o: 08
address cycles: 04
internal RAM size: 00010000
external RAM: S_DA_RAM_ERROR
done
Set baudrate (921600)...
done
interesting cpu type found: 6235:8B00:8A00
ram test...
testing 32bit...
32bit ram test passed
testing 16bit...
16bit ram test passed
ram test passed
===>  detect existing firmware structure...
detect ffs...
ffs offset/size: 02000000/02000000
firmware size: 32Mb
ffs size: 32Mb
detect sec ro...
detect custom parameters...
detect project-id...
project-id: TDCN8S_V2.1_19_512_0.3
detect NAND info...
number of areas/bytes to read: 1:00034000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
nfi area detection...
bootloader version: MTK35_09A_BOOTLOADER_V005_MT6235B_TDCN8S_V2_1_19_512_0_3.bin
nfi area detection (3 cores) finished: Ok
TCL-ID detection...
TCL-ID detection done
startup code area #1 detection...
startup code area #1 detection done
rom info ver: 07
sw version: MTK35_09A_PCB01_GPRS_MT6235B_S01.TDCN8S_V2_1_19_512_0_3.BIN
project-id: TDCN8S_V2.1_19_512_0.3, 00000000
code offset: 00000000
ffs offset/size [01]: 02000000/02000000
rom info structure: [standard] type (07)
TCL-ID is absent
===>  done
====================
New firmware found (v.3.82, database date: 04.04.2011): 
MTK35_09A_PCB01_GPRS_MT6235B_S01.TDCN8S_V2_1_19_512_0_3.BIN

This firmware is missing in support area. If this phone is good and working:

- download latest software from support area and try again, probably this firmware already supported in latest software
- make "Read full flash" operation
- send flash backup files to support: support@infinity-box.biz or upload files to http://rapidshare.com or http://4shared.com
- include in your e-mail full text from phone back label (phone name etc.)
====================
area size: 64Mb
number of areas/bytes to read: 1:04000000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...

tien19852007 · 04-18-2011, 16:28

why do you use the last version(3.30) or you try decrease baurate

anil_prajapati · 04-18-2011, 16:40

i can try all bautrate but same

InfinityHelp · 04-18-2011, 20:56

hello!

last Mmodule log was reading flash
"reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)..."

rameez_gsm · 04-20-2011, 08:54

Quote:

Originally Posted by anil_prajapati

Code:

COM28 [VCP0] selected
module  v3.29
Device: Autodetect 6205-6239 NOR
Checking data, wait...
advanced flash detection enabled
Action: read flash
====>  Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6235:8B00:8A01]...
CPU: MT6235
high speed boot On
chip: 0000:0000:0003
status: FF
boot packet size: 0400
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 11 sec
Remove/Install battery now !

Hello use new version chinese maricle software 3.30 & select 6253NOR type cpu.....

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
Eeprom reading	KLImax	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	2	09-22-2011 15:55
read eeprom write eeprom, what do i need?	jonthe	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	5	12-08-2010 05:24
unable to reads phone type..	Rosshire	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	2	07-17-2000 15:55
Silly question!! Why is it impossible to read out the mastercode of Nokia phones????	MyKe	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	0	09-26-1999 14:31

04-18-2011, 16:28	#4 (permalink)
tien19852007 Junior Member Join Date: Aug 2007 Posts: 22 Member: 570765 Status: Offline Thanks: 9 Thanked 2 Times in 2 Posts	why do you use the last version(3.30) or you try decrease baurate

04-18-2011, 16:40	#5 (permalink)
anil_prajapati Banned Join Date: Nov 2009 Posts: 1,207 Member: 1162712 Status: Offline Sonork: 100.1594855 Thanks: 218 Thanked 229 Times in 118 Posts	i can try all bautrate but same

04-18-2011, 20:56	#6 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Age: 36 Posts: 17,223 Member: 148515 Status: Offline Thanks: 2,319 Thanked 2,135 Times in 1,652 Posts	hello! last Mmodule log was reading flash "reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)..."