WG5 touchscreen calibration - GSM-Forum

Stoyan · 11-17-2010, 11:15

Well this is may be new model phone, bcs i cant find it anywhere.
Come to me with touchscreen working just in right side(when i press right-> indicates that i press in full left side). So calibration was fvcked.
Used all methods of calibration. Just on auto mode - calibration was disabled - i press anywhere on whole screen and just vibrating.
Tried ffs format all modes, then calibration -> same state.
When i formatted whole flash chip - phone dead.

I dont want to dissable touchscreen , i just want to calibrate it.
How to get calibration setting, phone have just 3 buttons.

Any suggestions are welcome

http://rapidshare.com/files/43136806...103836.B4M.bin

InfinityHelp · 11-17-2010, 21:26

hello!

restore phone to initial state by writing back backup.
after this is done access to phone settings and run "touchscreen calibration".
calibrate screen manually, by tapping test points

Stoyan · 11-18-2010, 09:50

access to phone settings and run "touchscreen calibration" -
impossible for now (touchscreen not function, just vibrate on touch)
Not any other buttons just 3 down, and volume up&down.

need factory reset by software

btw this a new firmware not in your database

InfinityHelp · 11-18-2010, 20:33

hello!

make format FFS, after that phone LCD will be touchable.
just will respond opposite.
access settings and run calibration via menu

Stoyan · 11-19-2010, 10:02

Finally i managed to enter in calibration menu.
But can not exit it

. Obviously i have damaged touchscreen.
Is that right?

InfinityHelp · 11-21-2010, 21:50

hello!

did you run it via phone menu? this is important

Stoyan · 11-22-2010, 09:43

yes i did. But calibration process is endless.
TY

InfinityHelp · 11-22-2010, 22:26

hello!

it could be either touchscreen problem or eeprm data fault.
currently NAND eeprom area is not writeable.
we are working under this

11-17-2010, 11:15	#1 (permalink)
Stoyan No Life Poster Join Date: Aug 2002 Location: BULGARIA Age: 53 Posts: 1,186 Member: 14868 Status: Offline Thanks Meter: 44	WG5 touchscreen calibration Well this is may be new model phone, bcs i cant find it anywhere. Come to me with touchscreen working just in right side(when i press right-> indicates that i press in full left side). So calibration was fvcked. Used all methods of calibration. Just on auto mode - calibration was disabled - i press anywhere on whole screen and just vibrating. Tried ffs format all modes, then calibration -> same state. When i formatted whole flash chip - phone dead. I dont want to dissable touchscreen , i just want to calibrate it. How to get calibration setting, phone have just 3 buttons. Any suggestions are welcome http://rapidshare.com/files/43136806...103836.B4M.bin

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
c35 EEPROM - calibration parameters	gin1978	x1x to x45/x50	34	03-03-2002 00:01
Help Me!S35 dead after calibration!!!	Witek	x1x to x45/x50	3	02-17-2002 17:47
NOKIA calibration?>	GsMen	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	18	09-07-2001 23:43
NEC DB2000 ????? NO L1 CALIBRATION DATA	Pandemonio100	Hardware Repair by brands	0	08-03-2001 19:37
rf calibration of 8850-wintesla	tagheuer	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	04-07-2001 05:25

11-17-2010, 21:26	#2 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! restore phone to initial state by writing back backup. after this is done access to phone settings and run "touchscreen calibration". calibrate screen manually, by tapping test points

11-18-2010, 09:50	#3 (permalink)
Stoyan No Life Poster Join Date: Aug 2002 Location: BULGARIA Age: 53 Posts: 1,186 Member: 14868 Status: Offline Thanks Meter: 44	access to phone settings and run "touchscreen calibration" - impossible for now (touchscreen not function, just vibrate on touch) Not any other buttons just 3 down, and volume up&down. need factory reset by software btw this a new firmware not in your database

11-18-2010, 20:33	#4 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! make format FFS, after that phone LCD will be touchable. just will respond opposite. access settings and run calibration via menu

11-19-2010, 10:02	#5 (permalink)
Stoyan No Life Poster Join Date: Aug 2002 Location: BULGARIA Age: 53 Posts: 1,186 Member: 14868 Status: Offline Thanks Meter: 44	Finally i managed to enter in calibration menu. But can not exit it . Obviously i have damaged touchscreen. Is that right?

11-21-2010, 21:50	#6 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! did you run it via phone menu? this is important

11-22-2010, 09:43	#7 (permalink)
Stoyan No Life Poster Join Date: Aug 2002 Location: BULGARIA Age: 53 Posts: 1,186 Member: 14868 Status: Offline Thanks Meter: 44	yes i did. But calibration process is endless. TY

11-22-2010, 22:26	#8 (permalink)
InfinityHelp Product Supporter Join Date: May 2005 Location: uae Posts: 29,245 Member: 148515 Status: Offline Thanks Meter: 19,534	hello! it could be either touchscreen problem or eeprm data fault. currently NAND eeprom area is not writeable. we are working under this