Post here successfully job with Z3X-BOX Samsung (2010-2018)

[jataarya]

I downloaded these two files from z3x site
COMBINATION_ODD_FA60_G610FDDU1AQF1
G610FDDU1BQI2_ODD1BQH9
Can some one guide me how to do frp reset?
Is these both the files are good?

[chipscell25]

FRP G930P BIT5 DONE

Operation: Reset FRP
Selected model: SM-G930P
Software version: 33.8

You must activate ADB before reset FRP Yes
Goto 'Terms and conditions' press 'NEXT' and 'AGREE' EULA Yes
Waiting ADB device... OK
Reading phone info...
Model: SM-G930P
Android version: 7.0
PDA version: G930PVPS5BRA1
CSC version: G930PSPT5BRA1
Phone version: G930PVPS5BRA1
Product code: Not Active
CSC country code: USA
CSC sales code: SPR
Phone SN: 00000000000
IMEI: 35356208XXXXXXX
HW version: REV0.6
RF cal date: 2017.01.03
Chip name: MSM8996
Modem board: MSM8996
Security patch: 2018-01-01
Boot Warranty bit: 0
Bypass FRP... OK
For complete reset FRP, goto 'Backup and reset' and make 'Factory data reset'

Done with Samsung Tool PRO v.33.8

[saifulhaq28]

Originally Posted by jataarya

I downloaded these two files from z3x site

COMBINATION_ODD_FA60_G610FDDU1AQF1

G610FDDU1BQI2_ODD1BQH9

Can some one guide me how to do frp reset?

Is these both the files are good?

1. First you flash with combination file.
2. After flash put download mode again and connect the phone with pc.
3. Select the stock rom what you have (4 file- BL, AP, CP, CSC)
4. Before you flash you have to select only “boot+sboot+recovery+system+cache”
5. Now your phone is bypassed (FRP)
Enjoy

[goodname]

Operation: Unlock
Selected model: SM-G890A
Software version: 33.8

Searching Samsung modem... detected COM101
Reading phone info...
Model: SM-G890A
AP version: G890AUCS6CPK8
CSC version: G890AATT6CPK8
CP version: G890AUCU7ARA1
Product code: SM-G890AZWAATT
Phone SN: R38H30SFJYJ
IMEI: 352130073066424
Unique number: 0316035924B22904
Reading IMEI... OK
IMEI: 352130073066424 (SIGN: OK)
Reading data from phone... OK
Unlocking... OK
Rebooting phone... OK
Unlock done

Done with Samsung Tool PRO v

[technomak]

Operation: Reset FRP UFS
Selected model: SM-G935F
Selected port: COM8 Z3X BOX Serial Port
Software version: 33.8

Hold 'Vol down' and press 'POWER ON' for 2-3 seconds
Checking phone at COM8 OK
Phone detected, do not release 'Vol down'
Reading data from phone... OK
Release 'Vol down' now
Comparing selected model... match (G935F)
Setup connection... OK
Reseting FRP... OK
Rebooting phone... OK
Reset FRP done

Done with Samsung Tool PRO v.33.8

[apologized]

Operation: Read Codes via Server
Selected model: SM-A730F
Software version: 33.8

Checking Login and Password... OK
Ballance: 10 crd.
You have 10 credit(s) left. This operation takes 5 credits.Continue?  Yes
Waiting ADB device... OK
Reading phone info...
Model: SM-A730F
Android version: 7.1.1
PDA version: A730FXXU2ARE2
CSC version: A730FOJM2ARE1
Phone version: A730FXXU2ARE1
Product code: SM-A730FZKEMAT
CSC country code: MOROCCO
CSC sales code: MAT
Phone SN: RF8K40FK5LA
IMEI: 352021090757295
HW version: MP 0.502
RF cal date: 20180406
Chip name: EXYNOS7885
Modem board: SHANNON327
Security patch: 2018-05-01
Boot Warranty bit: 0
Searching server... OK
Checking server answer... OK
Initialization zTool... OK
Running zTool, please wait...
Start... OK
Initialization... OK
Generate and check client proof... OK
Verify proof by client... OK
Executing... OK
Reading data from phone... OK
Calculating... OK
Searching server... OK
Waiting for server answer... OK
Freeze code: 52860484
NET lock: 90258272
SUB lock: 00000000
SP lock: 00000000
CP lock: 00000000
SIM lock: 00000000
For check lock status: *#7465625#

Done with Samsung Tool PRO v.33.8

[..::GMSR::..]

Operation: Patch Certificate
Selected model: SM-J530F
Software version: 33.8

Waiting ADB device... OK
Reading phone info...
Model: SM-J530F
Android version: 7.0
PDA version: J530FXWU2ARC1
CSC version: J530FOJV2ARC2
Phone version: J530FXXU2ARA2
Product code: SM-J530FZKAXFV
CSC country code: South Africa
CSC sales code: XFV
Phone SN: RF8J72LBFAM
IMEI: 356576586786781
HW version: MP 0.500
RF cal date: 20170724
Chip name: EXYNOS7870
Modem board: SHANNON315
Security patch: 2018-03-01
Boot Warranty bit: 1
Checking Super user right... true
Reading NV data... OK
Checking NV data... OK
Reading data... OK
Detecting MODEM... OK
Reading MODEM... OK
Calculating... OK
Writing zTool... OK
Initialization zTool... OK
Rebooting phone... OK
Patching CERT check... done

Done with Samsung Tool PRO v.33.8

[iAnell87]

Samsung SM_G531F FRP DONE

1. flash with ADB ENABLEhttps://mega.nz/#!2MBiSAzS!Kb6RO0wvT...VmXfaJ3QqwaVFA
2. FRP RESET WITH Z3X Pro

[tbwirelesstech]

You must activate ADB before reset FRP Yes
Goto 'Terms and conditions' press 'NEXT' and 'AGREE' EULA Yes
Waiting ADB device... OK
Reading phone info...
Model: SM-J327T1
Android version: 7.0
PDA version: J327T1UVS2ARE1
CSC version: J327T1TMK2ARE1
Phone version: J327T1UVS2ARE1
Product code: SM-J327TZSATMK
CSC country code: USA
CSC sales code: TMK
Phone SN: RV8K4138MWY
IMEI: 355417094758403
HW version: REV0.1
RF cal date: 20180425
Chip name: EXYNOS7570
Modem board: SHANNON305
Security patch: 2018-05-01
Boot Warranty bit: 0
Incorrect model selected. This may damage your phone. Continue? Yes
Bypass FRP... OK
For complete reset FRP, goto 'Backup and reset' and make 'Factory data reset'

no need for all the extra stuff...... just 1 file and your'e good

[tbwirelesstech]

You must activate ADB before reset FRP Yes
Goto 'Terms and conditions' press 'NEXT' and 'AGREE' EULA Yes
Waiting ADB device... OK
Reading phone info...
Model: SM-J327T1
Android version: 7.0
PDA version: J327T1UVS2ARE1
CSC version: J327T1TMK2ARE1
Phone version: J327T1UVS2ARE1
Product code: SM-J327TZSATMK
CSC country code: USA
CSC sales code: TMK
Phone SN: RV8K4138MWY
IMEI: 355417094758403
HW version: REV0.1
RF cal date: 20180425
Chip name: EXYNOS7570
Modem board: SHANNON305
Security patch: 2018-05-01
Boot Warranty bit: 0
Incorrect model selected. This may damage your phone. Continue? Yes
Bypass FRP... OK
For complete reset FRP, goto 'Backup and reset' and make 'Factory data reset'

no need for all the extra stuff...... just 1 file and your'e good

[alshanawe]

I'm facing problem connecting N900T , N910T to Z3X when activating the usb setting 0808 / DM+MODEM+ADB my z3x ADB won't detect

Actions done as below and still having the same problem:

* Before rooting and after rooting the same issue still going.
* Full flash done with N900T 5.0v / BBV N900TUVUFOL1 throw recovery mode Z3X pro.
* Charging connector replaced with new one.
* Different USB cables tried.

[yonic69]

What i always do is clean the charging port with cleaning solution(alcohol) and brush it inside of it, then i let it dry for a few seconds.
I hope that can help.


Enviado desde mi iPhone utilizando Tapatalk

[bk.gsm]

hello every one..

today I'm going to show you how to remove FRP from S7 EDGE android 8.0.0 with binary 2 without full flash@downgrade the version

first u need flash BL file from android 7 I used this file:

BL_G935FXXU2DRAG_CL12365438_QB16560168_REV00_user_low_ship.tar.md5

after flashing this file,boot your phone again into download mode,plug uart cable,chose the correct box comport and press reset FRP UFS....

phone will reboots to recovery mode,just press reboot system now....
after finishing setup the phone,oem must be activated then phone must be flashed with android 8 BL file...I used this file:

BL_G935FXXU2EREM_CL13438344_QB18291953_REV00_user_low_ship.tar.md5

and here is the logs:

[ 10/14/2018 4:58:16 PM ] Operation: Flash
[ 10/14/2018 4:58:16 PM ] Selected model: SM-G935F
[ 10/14/2018 4:58:17 PM ] Software version: 33.8
[ 10/14/2018 4:58:17 PM ] 
[ 10/14/2018 4:58:18 PM ] File analysis... OK
[ 10/14/2018 4:58:18 PM ] Total file size: 0x00544A20 (5 Mb)
[ 10/14/2018 4:58:19 PM ] Searching USB Flash interface... COM5 detected
[ 10/14/2018 4:58:19 PM ] Setup connection... OK
[ 10/14/2018 4:58:20 PM ] Reading PIT from phone... OK
[ 10/14/2018 4:58:21 PM ] Sending sboot.bin... OK
[ 10/14/2018 4:58:21 PM ] Sending param.bin... OK
[ 10/14/2018 4:58:22 PM ] Sending cm.bin... OK
[ 10/14/2018 4:58:23 PM ] Flashing done (time - 00:00:04)
[ 10/14/2018 4:58:23 PM ] 
[ 10/14/2018 4:59:31 PM ] Operation: Reset FRP UFS
[ 10/14/2018 4:59:32 PM ] Selected model: SM-G935F
[ 10/14/2018 4:59:32 PM ] Selected port: COM3 USB Serial Port
[ 10/14/2018 4:59:32 PM ] Software version: 33.8
[ 10/14/2018 4:59:32 PM ] 
[ 10/14/2018 4:59:33 PM ] Hold 'Vol down' and press 'POWER ON' for 2-3 seconds
[ 10/14/2018 4:59:33 PM ] Checking phone at COM3 OK
[ 10/14/2018 4:59:43 PM ] Phone detected, do not release 'Vol down'
[ 10/14/2018 4:59:43 PM ] Reading data from phone... OK
[ 10/14/2018 4:59:45 PM ] Release 'Vol down' now
[ 10/14/2018 4:59:47 PM ] Comparing selected model... match (G935F)
[ 10/14/2018 4:59:48 PM ] Setup connection... OK
[ 10/14/2018 4:59:48 PM ] Reseting FRP... OK
[ 10/14/2018 4:59:49 PM ] Rebooting phone... OK
[ 10/14/2018 4:59:50 PM ] Reset FRP done
[ 10/14/2018 4:59:50 PM ] 
[ 10/14/2018 5:02:55 PM ] Operation: Flash
[ 10/14/2018 5:02:55 PM ] Selected model: SM-G935F
[ 10/14/2018 5:02:56 PM ] Software version: 33.8
[ 10/14/2018 5:02:56 PM ] 
[ 10/14/2018 5:02:57 PM ] File analysis... OK
[ 10/14/2018 5:02:58 PM ] Total file size: 0x00533220 (5 Mb)
[ 10/14/2018 5:02:58 PM ] Searching USB Flash interface... COM5 detected
[ 10/14/2018 5:02:59 PM ] Setup connection... OK
[ 10/14/2018 5:02:59 PM ] Reading PIT from phone... OK
[ 10/14/2018 5:03:00 PM ] Sending sboot.bin.lz4... OK
[ 10/14/2018 5:03:00 PM ] Sending param.bin.lz4... OK
[ 10/14/2018 5:03:01 PM ] Sending cm.bin.lz4... OK
[ 10/14/2018 5:03:02 PM ] Flashing done (time - 00:00:03)
[ 10/14/2018 5:03:02 PM ]

Note:the tutorial only for Binary 2

b.r.

[ksm_lovers2000]

Operation: Reset FRP
Selected model: SM-G935T
Software version: 33.8

You must activate ADB before reset FRP Yes
Goto 'Terms and conditions' press 'NEXT' and 'AGREE' EULA Yes
Waiting ADB device... OK
Reading phone info...
Model: SM-G935T
Android version: 7.0
PDA version: G935TUVU4BQB1
CSC version: G935TTMB4BQB1
Phone version: G935TUVU4BQB1
Product code: Not Active
CSC country code: USA
CSC sales code: TMB
Phone SN: RF8H91SSLNA
IMEI: 357751075343480
HW version: MSM8996.00
RF cal date: 2016.03.06
Chip name: MSM8996
Modem board: MSM8996
Security patch: 2017-02-01
Boot Warranty bit: 0
Bypass FRP... OK
For complete reset FRP, goto 'Backup and reset' and make 'Factory data reset'

Done with Samsung Tool PRO v.33.8

[chipscell25]

FRP J530G USING J200M TALKBACK METHOD
we connect to the wifi (FULL INTERNET)
* we return to the beginning of the menu *
* we press with two fingers to activate talkback or if we press the two volume keys
* we draw an L on the screen
* we give talkback settings
* Let's help and comments
* about improved accessibility
* pley to the video of you tube that appears in the center
* we give you in the share arrow of you tube
* youtube opens
* We give back to the youtube share arrow
* we choose Gmail
* add an account in Outlock, (if you have it is easy to create one)
* We give you next two times, and the account will be synchronized
* We give Go to Gmail
* we give in the 3 dots and go to configuration
* at 3 dots again
*Account manager
* already with this we are within Settings.
* we go to applications
* We look for YouTube
*Mobile data
* see application settings
*about
*Privacy Policy
-We write Google up
-We write Chrome (or samsung browser)
-
in Chrome we look for the app that we all know QuickShortCutMaker.apk
-we select the first one that comes out and we download it
-When we think that you have already downloaded, we go to Favorites (it is in the tabs below)
then History, then Download history, there will be the downloaded app,
we install it and open it
-
in the app we write calculator and we give it where it says "try"
-We put the known code (+30012012732+
-brand * # 0808 #
-We activate the last option and the most important thing we give in REBOOT.

With this we will have ADB active and Quitanos the account with the tool we want.

In my case the Z3X in model j200m Remove frp but there are many more.


Operation: Reset FRP
Selected model: SM-J200M
Software version: 33.8

You must activate ADB before reset FRP Yes
Goto 'Terms and conditions' press 'NEXT' and 'AGREE' EULA Yes
Waiting ADB device... OK
Reading phone info...
Model: SM-J530G
Android version: 7.0
PDA version: J530GUBU1AQI4
CSC version: J530GUWA1AQJ1
Phone version: J530GUBU1AQI3
Product code: SM-J530GZDICDR
CSC country code: Dominican Republic
CSC sales code: CDR
Phone SN: RF8K10JAKKN
IMEI: 35717408XXXXXXX
HW version: MP 0.500
RF cal date: 20180106
Chip name: EXYNOS7870
Modem board: SHANNON315
Security patch: 2017-08-01
Boot Warranty bit: 0
Incorrect model selected. This may damage your phone. Continue? Yes
Bypass FRP... OK
For complete reset FRP, goto 'Backup and reset' and make 'Factory data reset'
Done with Samsung Tool PRO v.33.8