can i use setool com port in z3x software - GSM-Forum

quasim0438 · 02-06-2013, 08:59

does z3x box have same pinout as setool interface ?
i tried it with sam c160 , s7560m , both worked
do they match for all mobiles or not ?

deepakgarg · 02-06-2013, 11:05

Quote:

Originally Posted by quasim0438

does z3x box have same pinout as setool interface ?
i tried it with sam c160 , s7560m , both worked
do they match for all mobiles or not ?

setool pinouts and z3x pinouts are different so it might not work

quasim0438 · 02-06-2013, 15:31

Quote:

Originally Posted by deepakgarg

setool pinouts and z3x pinouts are different so it might not work

but i have flashed above mentioned models with setool com port in z3x software.
if rx tx mismatch then why these set connected and flashed successfully ?

deepakgarg · 02-06-2013, 15:42

may be i have different hardware

quasim0438 · 02-07-2013, 17:39

Selected model: C5212I_m
Selected com port: COM5
Selected speed port: 921600
Please, connect phone and press shortly power button
Phone Detected
Sending loader1... OK
ARM version 3B11
Sending loader2... OK
Flash ID: 00EC2206000100000034
Unlock block
Unlock block
Unlock - ok
If lock - not deactivate: Please make full reset *2767*3855# + input code #7465625*638*00000000#
Elapsed time: 137 second, sw ver: 3.5.0040

gsmfriend · 02-07-2013, 18:22

verify setool pinout here

but TX,RX in Z3x are pins 2,3 and 7,8 are gnd, pin1 is +5v

ORANGE MOB · 02-07-2013, 18:27

any Setool Like GPG with uni pin out Can possible use with z3x as interface

CAMA FRANCIS · 08-06-2013, 10:28

Using LGtool/SGtool software, Can UFS Tonado cable works on setool3 box com port?

02-06-2013, 08:59	#1 (permalink)
quasim0438 No Life Poster Join Date: Feb 2006 Location: P A K I S T A N Age: 42 Posts: 739 Member: 237155 Status: Offline Thanks Meter: 415	can i use setool com port in z3x software does z3x box have same pinout as setool interface ? i tried it with sam c160 , s7560m , both worked do they match for all mobiles or not ?

02-06-2013, 15:42	#4 (permalink)
deepakgarg No Life Poster Join Date: Jan 2006 Location: Chandigarh,India Age: 40 Posts: 5,790 Member: 220603 Status: Offline Thanks Meter: 1,164	may be i have different hardware

02-07-2013, 17:39	#5 (permalink)
quasim0438 No Life Poster Join Date: Feb 2006 Location: P A K I S T A N Age: 42 Posts: 739 Member: 237155 Status: Offline Thanks Meter: 415	Selected model: C5212I_m Selected com port: COM5 Selected speed port: 921600 Please, connect phone and press shortly power button Phone Detected Sending loader1... OK ARM version 3B11 Sending loader2... OK Flash ID: 00EC2206000100000034 Unlock block Unlock block Unlock - ok If lock - not deactivate: Please make full reset 27673855# + input code #746562563800000000# Elapsed time: 137 second, sw ver: 3.5.0040

02-07-2013, 18:27	#7 (permalink)
ORANGE MOB Product Supporter Join Date: Nov 2010 Location: Every where Posts: 2,936 Member: 1549240 Status: Offline Thanks Meter: 1,130	any Setool Like GPG with uni pin out Can possible use with z3x as interface

08-06-2013, 10:28	#8 (permalink)
CAMA FRANCIS Junior Member Join Date: Aug 2011 Posts: 17 Member: 1645482 Status: Offline Thanks Meter: 0	Using LGtool/SGtool software, Can UFS Tonado cable works on setool3 box com port?