Unsupported NOR Flash type

[riders4siam]

any solution to this problem? tried with spiderman v2.64 but the same.

Timer: _2010_4_28_11_6_11>> [MTK] Open COM7 success!
Timer: _2010_4_28_11_6_18>> Press ON/OFF key please...
Timer: _2010_4_28_11_6_21>> Target's hw_ver :0x8A02
Timer: _2010_4_28_11_6_21>> Target's hw_code :0x6228
Timer: _2010_4_28_11_6_21>> Target's sw_ver :0x8A02
Timer: _2010_4_28_11_6_23>> Get correct bootloader for target...
Timer: _2010_4_28_11_6_23>> MTK_AllInOne_DA_v3.0912.03.00
[DA0] selected!Timer: _2010_4_28_11_6_23>> You can release ON/OFF key!
Timer: _2010_4_28_11_6_23>> [DA] loading the 1st bootloader...
SuccessTimer: _2010_4_28_11_6_45>> [BROM] start to test UART link...
Timer: _2010_4_28_11_6_45>> Waiting the bootloader initilize...
Timer: _2010_4_28_11_6_50>> [COM] Success to set baudrate!
Timer: _2010_4_28_11_6_50>> [DA] Bootloader running now,OK
Timer: _2010_4_28_11_6_50>> [Note] Unsupported NOR Flash type!
Timer: _2010_4_28_11_6_50>> [Note] Please upgrade to lastest version,then try again!
Timer: _2010_4_28_11_6_50>> Boot the target fail,Abort!
Timer: _2010_4_28_11_6_50>> [MTK] Close COM7 success!

[verma rinku]

this is hardware problem check hardware

[riders4siam]

i have reflow heat to the NAND flash ic and now the sets turn on with progress bar and when it reach 100%, the LCD lights out but still withdraww current. anymore suggestion?

[inseee]

I think it is not hardware problem because, I got same message from a good working (NKTEL E71 mtk6235) set at the time of backup. I think Spiderman this version not support that using flash IC. wait for next update.

[riders4siam]

Originally Posted by riders4siam

i have reflow heat to the NAND flash ic and now the sets turn on with progress bar and when it reach 100%, the LCD lights out but still withdraww current. anymore suggestion?

the flash backup was successfull but when i rewrite the backup file, this error comes up. here's the log

Timer: _2010_4_29_21_4_53>> [MTK] Open COM7 success!
Timer: _2010_4_29_21_4_53>> Press ON/OFF key please...
Timer: _2010_4_29_21_4_54>> Target's hw_ver :0x8A02
Timer: _2010_4_29_21_4_54>> Target's hw_code :0x6228
Timer: _2010_4_29_21_4_54>> Target's sw_ver :0x8A02
Timer: _2010_4_29_21_4_56>> Get correct bootloader for target...
Timer: _2010_4_29_21_4_56>> MTK_AllInOne_DA_v3.0912.03.00
[DA0] selected!Timer: _2010_4_29_21_4_56>> You can release ON/OFF key!
Timer: _2010_4_29_21_4_56>> [DA] loading the 1st bootloader...
SuccessTimer: _2010_4_29_21_5_19>> [BROM] start to test UART link...
Timer: _2010_4_29_21_5_19>> Waiting the bootloader initilize...
Timer: _2010_4_29_21_5_24>> [COM] Success to set baudrate!
Timer: _2010_4_29_21_5_24>> [DA] Bootloader running now,OK
Timer: _2010_4_29_21_5_24>> [DA]Start to downloading:A688_R6000TV_TL_ML_01_0.4T04S1114.bin
Timer: _2010_4_29_21_5_24>> nand_total_size = [04200000H]
Timer: _2010_4_29_21_5_24>> [FILE]analysising flash file...
Timer: _2010_4_29_21_5_24>> Boot_Ver:V005
BootSize:0x5750Timer: _2010_4_29_21_5_24>> [FILE]Image1:Off_Block[0x2] size:[0x51AA78]
Timer: _2010_4_29_21_5_24>> [FILE]Image2:Off_Block[0x149] size:[0xE12A10]
Timer: _2010_4_29_21_5_24>> [FILE]Attrible Page = 0x5F
Timer: _2010_4_29_21_5_24>> Start to read flash block...
Timer: _2010_4_29_21_5_24>> [FILE]Malloc memory for flash success!
Timer: _2010_4_29_21_5_24>> [FILE]Get bootloader zone success!
Timer: _2010_4_29_21_5_24>> [ERR] Read Image1 error!Pos=0x40 Size:0x51AA78
Timer: _2010_4_29_21_5_25>> [MTK] Close COM7 success!