Another Sharp 902SH - GSM-Forum

vitaminc1 · 04-24-2010, 12:47

There is power when i connect cable to phone sharp902sh/battery full - also tried with several older version that work with this model but always failing to recognize phone

Code:

v0.91380095/UNI
Card serial:00xxxxx
Loaded 51 flash descriptors
No server found.
CARD COUNTERS: FLASH 0, UNLOCK 0
Elapsed:2 secs.
No server found.
CARD COUNTERS: FLASH 0, UNLOCK 0
Elapsed:2 secs.
Open COM port OK
Abort all operations.
phone pre-boot failed,possible RECOVERY needed.
Elapsed:129 secs.
RECOVERY MODE STARTED
Open COM port OK
Abort all operations.
Elapsed:70 secs.

even when i try to recover Phone just says Please wait.. and goes off in sort of grey/black screen. Already read all solutions here and some other forums but can't use it cause phone is not even recognized by sw.Any idea i might try?

vitaminc1 · 04-27-2010, 18:06

Full Flash with Setool now phone working Ok with original IMEI.

Code:

v0.914035/UNI
CARD SERIAL: 00
Loaded 51 flash descriptors
Open COM port OK
ChipID:7100,EMP protocol:0301

PHONE IS BROWN
FLASH CID detected:24
Speed:921600
DB2000 only supports 460800,fallback.
OTP LOCKED:1 CID:24 PAF:0 IMEI:350257xxxxxx CERT:BROWN
LDR:040622 1339 LLECXC1325712_PRODUCTION P2J
Flash ID check:B00B
Flash props sent ok
Setting up GDFS...
IMEI MISMATCH !!!! POSSIBLE STOLEN PHONE !!!!!
ORIGINAL IMEI:35025700xxxxxx
CURRENT IMEI:35025700664327
Writing simlocks...
ALL UNLOCK/LOCK CODES SET TO "74373411"
Signing...
control keys complete.
full sig complete.
Unlock DONE
Elapsed: 28 secs.
Open COM port OK
phone pre-boot failed,possible RECOVERY needed.
PROCEDURE WAS STOPPED BY USER
Elapsed: 7 secs.
Open COM port OK
ChipID:7100,EMP protocol:0301

PHONE IS BROWN
FLASH CID detected:24
Speed:921600
DB2000 only supports 460800,fallback.
OTP LOCKED:1 CID:24 PAF:0 IMEI:350257006xxxxxx CERT:BROWN
LDR:040622 1339 LLECXC1325712_PRODUCTION P2J
Flash ID check:B00B
Flash props sent ok
Switching to USB...
interface not changed
writing C:\SeTool_older\v0.914035\firmware\902_133ferrari\1.33F.ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:642
Will flash 642 blocks...
SSW loading returns:0
writing C:\SeTool_older\v0.914035\firmware\902_133ferrari\21C0_TPR7D_J300_Type1_ver1.00build066_Sharp.ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:64
Will flash 64 blocks...
SSW loading returns:0
writing C:\SeTool_older\v0.914035\firmware\902_133ferrari\2220_FS(forTPR7D)_ver1.00build061_Sharp.ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:16
Will flash 16 blocks...
SSW loading returns:0
writing C:\SeTool_older\v0.914035\firmware\902_133ferrari\Checksum_java1.33F.ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:1
Will flash 1 blocks...
SSW loading returns:0
writing C:\SeTool_older\v0.914035\firmware\902_133ferrari\FSB220(2M,SharpFlash).ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:32
Will flash 32 blocks...
SSW loading returns:0
writing C:\SeTool_older\v0.914035\firmware\902_133ferrari\JPA2241_Ferrari.ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:5
Will flash 5 blocks...
SSW loading returns:0
writing C:\SeTool_older\v0.914035\firmware\902_133ferrari\scgd_0block_InitFlagOn.ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:1
Will flash 1 blocks...
SSW loading returns:0
Setting up GDFS...
Writing simlocks...
ALL UNLOCK/LOCK CODES SET TO "77840503"
Signing...
control keys complete.
full sig complete.
Elapsed: 1190 secs.
Open COM port OK
ChipID:7100,EMP protocol:0301

PHONE IS BROWN
FLASH CID detected:24
Speed:921600
DB2000 only supports 460800,fallback.
OTP LOCKED:1 CID:24 PAF:0 IMEI:350257006xxxxx CERT:BROWN
LDR:040622 1339 LLECXC1325712_PRODUCTION P2J
Flash ID check:B00B
Flash props sent ok
Switching to USB...
interface not changed
writing C:\SeTool_older\v0.914035\firmware\sharp902_144_euro\1.40H.ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:644
Will flash 644 blocks...
SSW loading returns:0
writing C:\SeTool_older\v0.914035\firmware\sharp902_144_euro\21C0_TPR7D_J300_Type1_ver1.00build066_Sharp.ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:64
Will flash 64 blocks...
SSW loading returns:0
writing C:\SeTool_older\v0.914035\firmware\sharp902_144_euro\2220_FS(forTPR7D)_ver1.00build061_Sharp.ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:16
Will flash 16 blocks...
SSW loading returns:0
writing C:\SeTool_older\v0.914035\firmware\sharp902_144_euro\Checksum_java1.40H.ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:1
Will flash 1 blocks...
SSW loading returns:0
writing C:\SeTool_older\v0.914035\firmware\sharp902_144_euro\FSB220(2M,SharpFlash).ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:32
Will flash 32 blocks...
SSW loading returns:0
writing C:\SeTool_older\v0.914035\firmware\sharp902_144_euro\GDATA4_2170.ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:8
Will flash 8 blocks...
SSW loading returns:0
writing C:\SeTool_older\v0.914035\firmware\sharp902_144_euro\JPA2240.ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:6
Will flash 6 blocks...
SSW loading returns:0
writing C:\SeTool_older\v0.914035\firmware\sharp902_144_euro\scgd_0block_InitFlagOn.ssw.cry
CURRENT FLASH FILE CID:24
SSW uses dynamic hash, dynamic hash len is:1
Will flash 1 blocks...
SSW loading returns:0
Setting up GDFS...
Writing simlocks...
ALL UNLOCK/LOCK CODES SET TO "52743038"
Signing...
control keys complete.
full sig complete.
Elapsed: 1196 secs.

recoshaa · 11-15-2011, 22:06

how did you get the phone to detect on setool

04-24-2010, 12:47	#1 (permalink)
vitaminc1 Junior Member Join Date: Mar 2010 Posts: 30 Member: 1256230 Status: Offline Thanks Meter: 4	Another Sharp 902SH There is power when i connect cable to phone sharp902sh/battery full - also tried with several older version that work with this model but always failing to recognize phone Code: v0.91380095/UNI Card serial:00xxxxx Loaded 51 flash descriptors No server found. CARD COUNTERS: FLASH 0, UNLOCK 0 Elapsed:2 secs. No server found. CARD COUNTERS: FLASH 0, UNLOCK 0 Elapsed:2 secs. Open COM port OK Abort all operations. phone pre-boot failed,possible RECOVERY needed. Elapsed:129 secs. RECOVERY MODE STARTED Open COM port OK Abort all operations. Elapsed:70 secs. even when i try to recover Phone just says Please wait.. and goes off in sort of grey/black screen. Already read all solutions here and some other forums but can't use it cause phone is not even recognized by sw.Any idea i might try?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
My 5130 shows 25 mA in stdby, another 4mA in Netmonitor test 23	mr_x4you	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	12-23-2001 11:07
another freakin' update...	Dark Lemming	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	5	10-02-2001 23:24
another 3210 problem	Joker	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	08-26-2001 22:56
Another opinion	Nitas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	03-14-2000 20:34
Copy from one 6110 to another	Leif Nielsen	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	06-10-1999 22:36

11-15-2011, 22:06	#3 (permalink)
recoshaa Banned Join Date: Mar 2009 Location: paradise Posts: 312 Member: 1000967 Status: Offline Thanks Meter: 27	how did you get the phone to detect on setool