No Power Sh903 Vodafone Succesful in flashing via TP in SE TOOL but still No power - GSM-Forum

dmaetrey · 03-07-2008, 08:48

I have Downloaded EU flashfile,China,Japan,taiwan, even 2 pcs read outs at the support!!! still no luck!!! what should i do???

Help

this was auto-off before!!! but now it is DEAD!~

HELP!

Quote:

v0.914026/UNI
CARD SERIAL: 0000VVVV
Loaded 51 flash descriptors
Connecting to UFS...
Found 1 FTDI device(s).
UFS #2243 READY
ATTACH TESTPOINT NOW, THEN PRESS "READY"
phone pre-boot failed,possible RECOVERY needed.
PROCEDURE WAS STOPPED BY USER
Elapsed: 95 secs.
ATTACH TESTPOINT NOW, THEN PRESS "READY"
phone pre-boot failed,possible RECOVERY needed.
PROCEDURE WAS STOPPED BY USER
Elapsed: 99 secs.
ATTACH TESTPOINT NOW, THEN PRESS "READY"
ChipID:7100,EMP protocol:0301
PHONE IS BLACK (00000000)
NO VALID FLASH CID DETECTED (103)
Speed:921600
DB2000 only supports 460800,fallback.
RELEASE TESTPOINT NOW, THEN PRESS "READY"
OTP LOCKED:1 CID:24 PAF:0 IMEI:35472100ZZZZZZ CERT:N/A
LDR:040622 1339 LLECXC1325712_PRODUCTION P2J
Flash ID check:B00B
Flash props sent ok
Switching to USB...
interface not changed
writing C:\a Sony Eric SE TOOL\sharp flashfiles\tw_1.03Q_9121_1.21_p1.ssw
CURRENT FLASH FILE CID:254
SSW uses dynamic hash, dynamic hash len is:528
Will flash 528 blocks...
SSW loading returns:0
writing C:\a Sony Eric SE TOOL\sharp flashfiles\tw_1.03Q_9121_1.21_p2.ssw
CURRENT FLASH FILE CID:254
SSW uses dynamic hash, dynamic hash len is:232
Will flash 232 blocks...
SSW loading returns:0
Elapsed: 1744 secs.
ATTACH TESTPOINT NOW, THEN PRESS "READY"
phone pre-boot failed,possible RECOVERY needed.
PROCEDURE WAS STOPPED BY USER
Elapsed: 97 secs.
ATTACH TESTPOINT NOW, THEN PRESS "READY"
ChipID:7100,EMP protocol:0301
PHONE IS BLACK (00000000)
NO VALID FLASH CID DETECTED (103)
Speed:921600
DB2000 only supports 460800,fallback.
RELEASE TESTPOINT NOW, THEN PRESS "READY"
OTP LOCKED:1 CID:24 PAF:0 IMEI:35472100ZZZZZZ CERT:N/A
LDR:040622 1339 LLECXC1325712_PRODUCTION P2J
Flash ID check:B00B
Flash props sent ok
Sharp3G patching started.
FOUND MODEL 9121 REV 1.21 VER 1.03Q
patch#0 not found
patch#1 not found
patch#2 not found
patch#3 not found
patch#4 not found
Setting up GDFS...
Writing simlocks...
ALL UNLOCK/LOCK CODES SET TO "66075666"
Signing...
control keys complete.
full sig complete.
Unlock DONE
Elapsed: 134 secs.

dmaetrey · 03-07-2008, 09:43

pls anybody help!!!
hope someone could help me

thanks!

dmaetrey · 03-08-2008, 01:40

i've been waiting for someone to help
and advice!!!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
z610i you can flash the phone but still no power	whalz	DreamBox	2	05-15-2008 21:53
j210i complete flashing but still no power	martin0709	Sony Ericsson	2	08-03-2006 13:09
c62 dead....flashing but still no power	megone	FuriouS II	6	10-18-2005 11:47
Flash 100% ok in dead 3310 but still no power	Burnt Cobba	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	18	09-14-2002 09:20

03-07-2008, 09:43	#2 (permalink)
dmaetrey No Life Poster Join Date: Jul 2006 Posts: 1,152 Member: 315550 Status: Offline Thanks: 418 Thanked 112 Times in 61 Posts	pls anybody help!!! hope someone could help me thanks!

03-08-2008, 01:40	#3 (permalink)
dmaetrey No Life Poster Join Date: Jul 2006 Posts: 1,152 Member: 315550 Status: Offline Thanks: 418 Thanked 112 Times in 61 Posts	i've been waiting for someone to help and advice!!!