bold 9000 - GSM-Forum

sweetboy · 02-24-2010, 21:12

any body has solution for this error
please help

Unable to reconnect to the device during a multi-stage load operation.

The_Dj · 02-24-2010, 22:49

writing with Destock manager¿¿¿¿

sweetboy · 02-24-2010, 23:38

i have try that same problem i have 2 bold 9000 do ing same thing

Quote:

writing with Destock manager¿¿¿¿

**delower10** · 02-25-2010, 07:18

Quote:

Originally Posted by sweetboy

i have try that same problem i have 2 bold 9000 do ing same thing

Uninstall DM & install again DM5
restart PC
then make flash with loader.exe
Make sure u have 60% up charged at battery

Post report !

BR
Delower

sweetboy · 02-25-2010, 14:42

i have try your solution still
at waite for device installation
after that is not loading
i have try dm5/ dm4.6
when i try mfi its wipe and erase good with 1 on screen

Quote:

Uninstall DM & install again DM5
restart PC
then make flash with loader.exe
Make sure u have 60% up charged at battery

**delower10** · 02-25-2010, 15:01

Quote:

Originally Posted by sweetboy

i have try your solution still
at waite for device installation
after that is not loading
i have try dm5/ dm4.6
when i try mfi its wipe and erase good with 1 on screen

Did u typed START ?

if u didn't type START the u will get (unable to reconnect ...... )

BR
Delower

sweetboy · 02-25-2010, 15:49

i have bold screen radio core cat failed reset

Quote:

Did u typed START ?

if u didn't type START the u will get (unable to reconnect ...... )

The_Dj · 02-25-2010, 16:08

go to config net
and select only 2G

dez com · 02-25-2010, 16:28

Quote:

Originally Posted by sweetboy

any body has solution for this error
please help

Unable to reconnect to the device during a multi-stage load operation.

your solution is batt charge your batt well or change it and reflash your problem will soft 100%100%

lugarte · 02-25-2010, 16:32

its works whit DM 4.6 and type START in phone

**delower10** · 02-26-2010, 02:35

Quote:

Originally Posted by dez com

your solution is batt charge your batt well or change it and reflash your problem will soft 100%100%

Yes buddy i am agree with you.
If possible then change the battery.
Look at your network settings, make sure you set to use only 2G.

BR
Delower

umarmsn · 02-26-2010, 03:52

i have 8300 when put battery, it just show red led but phone not power on. how to fix it? i suppose it is flash so where to get it?

tigran80 · 02-26-2010, 08:19

Quote:

Originally Posted by umarmsn

i have 8300 when put battery, it just show red led but phone not power on. how to fix it? i suppose it is flash so where to get it?

download from blackberry.com or via torrent file I have attached.

chezral · 02-26-2010, 14:42

Did you get thru sweetboy?

The core cat failed error was probably due to 3g being enabled. If you can get the phone working, change network to 2g as others recommended.
First it either needs to wiped with JL Commander or use mfi to wipe/nuke, then flash.

Usually after i get a '1' after mfi, I press the power button, then type start, then flash the phone.
Like others said, most of the time 'could not connect multi-stage operation' problem is the battery. It either needs fully charging or try using another good battery.
But getting the '1' from mfi is good, usually 99% of error/red blink phones will flash good after seeing that on display.

BR

sweetboy · 02-28-2010, 02:05

Quote:

Did you get thru sweetboy?

The core cat failed error was probably due to 3g being enabled. If you can get the phone working, change network to 2g as others recommended.
First it either needs to wiped with JL Commander or use mfi to wipe/nuke, then flash.

Usually after i get a '1' after mfi, I press the power button, then type start, then flash the phone.
Like others said, most of the time 'could not connect multi-stage operation' problem is the battery. It either needs fully charging or try using another good battery.
But getting the '1' from mfi is good, usually 99% of error/red blink phones will flash good after seeing that on display.

phone still same i have try it with new battery
no luck

02-24-2010, 21:12	#1 (permalink)
sweetboy No Life Poster Join Date: May 2005 Age: 48 Posts: 846 Member: 146939 Status: Offline Thanks: 197 Thanked 177 Times in 70 Posts	bold 9000 any body has solution for this error please help Unable to reconnect to the device during a multi-stage load operation.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
Unlock Blackberry Bold 9000	malyfsborin88	Phone Unlocking Codes & Maps	1	10-30-2008 00:56

02-24-2010, 22:49	#2 (permalink)
The_Dj No Life Poster Join Date: Sep 2005 Location: ๑۩۞۩&& Posts: 1,229 Member: 178790 Status: Offline Sonork: 100.1593063 Thanks: 550 Thanked 1,235 Times in 255 Posts	writing with Destock manager¿¿¿¿

02-25-2010, 16:08	#8 (permalink)
The_Dj No Life Poster Join Date: Sep 2005 Location: ๑۩۞۩&& Posts: 1,229 Member: 178790 Status: Offline Sonork: 100.1593063 Thanks: 550 Thanked 1,235 Times in 255 Posts	go to config net and select only 2G

02-25-2010, 16:32	#10 (permalink)
lugarte Junior Member Join Date: Feb 2007 Posts: 4 Member: 458451 Status: Offline Thanks: 7 Thanked 0 Times in 0 Posts	its works whit DM 4.6 and type START in phone

02-26-2010, 03:52	#12 (permalink)
umarmsn No Life Poster Join Date: Oct 2007 Location: SL3 UNLOCK WITH IN 1 HOURS SER Age: 27 Posts: 2,753 Member: 616909 Status: Online Sonork: 1619121 Thanks: 188 Thanked 339 Times in 236 Posts	i have 8300 when put battery, it just show red led but phone not power on. how to fix it? i suppose it is flash so where to get it?

02-26-2010, 14:42	#14 (permalink)
chezral Freak Poster Join Date: Nov 2005 Posts: 253 Member: 203715 Status: Offline Thanks: 111 Thanked 231 Times in 41 Posts	Did you get thru sweetboy? The core cat failed error was probably due to 3g being enabled. If you can get the phone working, change network to 2g as others recommended. First it either needs to wiped with JL Commander or use mfi to wipe/nuke, then flash. Usually after i get a '1' after mfi, I press the power button, then type start, then flash the phone. Like others said, most of the time 'could not connect multi-stage operation' problem is the battery. It either needs fully charging or try using another good battery. But getting the '1' from mfi is good, usually 99% of error/red blink phones will flash good after seeing that on display. BR