Bold 9000 charging port - GSM-Forum

SIXTUS · 09-10-2010, 14:01

I'm in a very hot soup!!!!!
I tried to replace bold 9000 charging port, in the process of removing the bad one it pull from the panel base. so no way to slder the new one.pls can someone here give me a picture on how to run the wire, i have searched the entire forum but i cant get the diagram... i need very urgent pls, pls and pls

10x in advance for ever can help me out

cpr.orlando · 09-10-2010, 17:08

Not sure there is are other contacts anywhere else on a 9000.. Just hang tight some one might know

SIXTUS · 09-10-2010, 17:40

i hope some one will, otherwise i am buying a new phone, cos i dont know how to tell customers stories.

SIXTUS · 09-24-2010, 09:58

i am still holding tight, can some pls make some move pls.

Hussein_Gramon · 09-24-2010, 15:23

your answer is here
http://forum.gsmhosting.com/vbb/6358362-post1.html

enjoy it

gsm_freak · 09-24-2010, 17:01

here sir.... it might help you..

TESTED 100 percent working...

enjoy.................

wbr,

brew99 · 09-24-2010, 18:44

Althought this solution might work, it isn't really a very usable one due to the requirement of removing the sheild to get to that small IC (Escpecially if this is a customers phone). What we really need is a solution that doesn't require the removal of the shield!

SIXTUS · 09-24-2010, 19:03

thank u all 4 this posts i will tyr it tomorrow and post result.
@brew99
it doesnt matter where the connection is, the most important thing is to solve ur customers problem, he doesnt care how ur solve it, as far as the problem is fixed and the data is intact.

Rise · 10-07-2011, 19:26

it's much better to cut the shield on working side, more safe and recommended.

09-10-2010, 14:01	#1 (permalink)
SIXTUS No Life Poster Join Date: Jun 2004 Age: 45 Posts: 562 Member: 69727 Status: Offline Thanks Meter: 49	Bold 9000 charging port I'm in a very hot soup!!!!! I tried to replace bold 9000 charging port, in the process of removing the bad one it pull from the panel base. so no way to slder the new one.pls can someone here give me a picture on how to run the wire, i have searched the entire forum but i cant get the diagram... i need very urgent pls, pls and pls 10x in advance for ever can help me out

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Phone Not Charging	tiggerwilk	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	10-21-2012 16:23
Charging.	PhoeniX	Nokia Hardware & Hardware Repair	7	07-06-2004 08:35
51xx charging problem	kage	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	9	03-06-2002 00:42
how to charge your battery?	g2000	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	12	09-26-2000 14:32
Is it possible to use the Nokia 6150 with the IR Port of a Toshiba Laptop?	telefonman	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	02-13-2000 20:06

09-10-2010, 17:08	#2 (permalink)
cpr.orlando Freak Poster Join Date: Aug 2008 Location: cpr-orlando.com Posts: 369 Member: 843747 Status: Offline Thanks Meter: 40	Not sure there is are other contacts anywhere else on a 9000.. Just hang tight some one might know

09-10-2010, 17:40	#3 (permalink)
SIXTUS No Life Poster Join Date: Jun 2004 Age: 45 Posts: 562 Member: 69727 Status: Offline Thanks Meter: 49	i hope some one will, otherwise i am buying a new phone, cos i dont know how to tell customers stories.

09-24-2010, 09:58	#4 (permalink)
SIXTUS No Life Poster Join Date: Jun 2004 Age: 45 Posts: 562 Member: 69727 Status: Offline Thanks Meter: 49	i am still holding tight, can some pls make some move pls.

09-24-2010, 15:23	#5 (permalink)
Hussein_Gramon Insane Poster Join Date: Jan 2006 Posts: 80 Member: 225297 Status: Offline Thanks Meter: 7	your answer is here http://forum.gsmhosting.com/vbb/6358362-post1.html enjoy it

09-24-2010, 17:01	#6 (permalink)
gsm_freak Freak Poster Join Date: Dec 2005 Location: inside nibiru Posts: 172 Member: 205990 Status: Offline Thanks Meter: 73	here sir.... it might help you.. TESTED 100 percent working... enjoy................. wbr,

09-24-2010, 18:44	#7 (permalink)
brew99 Junior Member Join Date: May 2010 Posts: 30 Member: 1311370 Status: Offline Thanks Meter: 3	Althought this solution might work, it isn't really a very usable one due to the requirement of removing the sheild to get to that small IC (Escpecially if this is a customers phone). What we really need is a solution that doesn't require the removal of the shield!

09-24-2010, 19:03	#8 (permalink)
SIXTUS No Life Poster Join Date: Jun 2004 Age: 45 Posts: 562 Member: 69727 Status: Offline Thanks Meter: 49	thank u all 4 this posts i will tyr it tomorrow and post result. @brew99 it doesnt matter where the connection is, the most important thing is to solve ur customers problem, he doesnt care how ur solve it, as far as the problem is fixed and the data is intact.

10-07-2011, 19:26	#9 (permalink)
Rise No Life Poster Join Date: Sep 2003 Location: Dubai Posts: 1,402 Member: 39022 Status: Offline Sonork: 1575244 Thanks Meter: 94	it's much better to cut the shield on working side, more safe and recommended.