MSL data corrupt - GSM-Forum

iceburnmarko · 03-19-2010, 15:05

Trying to unlock a S5230 phone. Have done 2 or 3 already and was fine. But today this phone wont unlock. (for some reason on the log it have not recorded the data when it went into servicemode) :-(

Rescanning ports...
Detected COM3 - STATUS: READY (COM)
Detected COM55 - STATUS: READY (MODEM)
13:46:08 - Broadcom Bootloader mode: Done
13:46:08 - Reading NAND data..Please Wait
(Remark: This can take up to 1 minute)
13:46:21 - Reading Done, Rebooting Phone
13:48:31 - Calculating MSL Security...Please Wait...
13:48:31 - MSL Data Corrupt

Now I wonder is the way to fix it goto advanced options and than put what IMEI and serial number that is on the handset? Or is it something else?

ssa · 03-19-2010, 19:15

try set the speed to normal instead of fast, then remove battery from phone, insert battery, and power on, now press direct unlock

iceburnmarko · 03-19-2010, 22:30

Did retry before posting normal transmission and took battery out, put it back in and power it up (mainly to be honest to get the IMEI & Serial off the back of the handset.) To check if it made any different

But something I didnt say at the beginning cause Jim who orginally did the handset only told me after I sent the original posting. (if it make a different.) First time he did have it on FAST, and it was doing it but whilst it was reading or writing to handset the battery of the phone fell out. Than when repeat that error came up.

Using NSPRO box as interface and E210 cable.

NNB: Surprise u replied SSA throught you would be too busy with new member of the family :-)..

Salami1_1 · 03-20-2010, 04:38

If you hit *#06# what do you get? normal IMEI or is it damaged? Because it is very likely you have some (or a lot) of corrupted data. Loosing connection while unlocking is like when of the worst things that can happen (that is why manual states like 100 times make sure battery is fully charged

).

iceburnmarko · 03-20-2010, 09:50

He just type the #*06# and the IMEI that come up is the same that is on the back of the handset.

iceburnmarko · 03-20-2010, 10:47

Just to keep you updated today did it on NSPRO and finish it and unlock it :-). Which is strange since one reason why got SRS cause NSPRO normally dont do S5600 / 5230 :-). Oh well at least it is unlock now he is happy.

03-19-2010, 15:05	#1 (permalink)
iceburnmarko Freak Poster Join Date: May 2008 Posts: 105 Member: 773305 Status: Offline Thanks: 11 Thanked 14 Times in 8 Posts	MSL data corrupt Trying to unlock a S5230 phone. Have done 2 or 3 already and was fine. But today this phone wont unlock. (for some reason on the log it have not recorded the data when it went into servicemode) :-( Rescanning ports... Detected COM3 - STATUS: READY (COM) Detected COM55 - STATUS: READY (MODEM) 13:46:08 - Broadcom Bootloader mode: Done 13:46:08 - Reading NAND data..Please Wait (Remark: This can take up to 1 minute) 13:46:21 - Reading Done, Rebooting Phone 13:48:31 - Calculating MSL Security...Please Wait... 13:48:31 - MSL Data Corrupt Now I wonder is the way to fix it goto advanced options and than put what IMEI and serial number that is on the handset? Or is it something else?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
M620 can't Restore MSL Data	siyamack	UST Pro II	2	03-30-2010 22:09
M620 can't Restore MSL Data	siyamack	HWK	14	03-30-2010 12:04
C140 MSL data analyse failed	kabiyal	UST Pro II	1	02-05-2010 10:53
cant get msl data?	YASMOBILENEEDS	Ultimate-Sam	4	12-22-2008 21:06
PMB6850 "flash data corrupted!"	chavrotti	Infineon C16X M51 & ARM7 M52 BASED	4	05-08-2004 19:54

03-19-2010, 19:15	#2 (permalink)
ssa No Life Poster Join Date: Feb 2003 Location: Inside CPU Age: 32 Posts: 1,775 Member: 23420 Status: Offline Thanks: 52 Thanked 3,023 Times in 420 Posts	try set the speed to normal instead of fast, then remove battery from phone, insert battery, and power on, now press direct unlock

03-19-2010, 22:30	#3 (permalink)
iceburnmarko Freak Poster Join Date: May 2008 Posts: 105 Member: 773305 Status: Offline Thanks: 11 Thanked 14 Times in 8 Posts	Did retry before posting normal transmission and took battery out, put it back in and power it up (mainly to be honest to get the IMEI & Serial off the back of the handset.) To check if it made any different But something I didnt say at the beginning cause Jim who orginally did the handset only told me after I sent the original posting. (if it make a different.) First time he did have it on FAST, and it was doing it but whilst it was reading or writing to handset the battery of the phone fell out. Than when repeat that error came up. Using NSPRO box as interface and E210 cable. NNB: Surprise u replied SSA throught you would be too busy with new member of the family :-)..

03-20-2010, 04:38	#4 (permalink)
Salami1_1 No Life Poster Join Date: Apr 2001 Posts: 1,552 Member: 3941 Status: Offline Thanks: 35 Thanked 619 Times in 125 Posts	If you hit *#06# what do you get? normal IMEI or is it damaged? Because it is very likely you have some (or a lot) of corrupted data. Loosing connection while unlocking is like when of the worst things that can happen (that is why manual states like 100 times make sure battery is fully charged ).

03-20-2010, 09:50	#5 (permalink)
iceburnmarko Freak Poster Join Date: May 2008 Posts: 105 Member: 773305 Status: Offline Thanks: 11 Thanked 14 Times in 8 Posts	He just type the #*06# and the IMEI that come up is the same that is on the back of the handset.

03-20-2010, 10:47	#6 (permalink)
iceburnmarko Freak Poster Join Date: May 2008 Posts: 105 Member: 773305 Status: Offline Thanks: 11 Thanked 14 Times in 8 Posts	Just to keep you updated today did it on NSPRO and finish it and unlock it :-). Which is strange since one reason why got SRS cause NSPRO normally dont do S5600 / 5230 :-). Oh well at least it is unlock now he is happy.