GSM-Forum

GSM-Forum (http://forum.gsmhosting.com/vbb/)
-   McnPro Box (http://forum.gsmhosting.com/vbb/f532/)
-   -   ★★★★★Discussion here>> Mcnpro Box version 3.3.0 ★★★★★ (http://forum.gsmhosting.com/vbb/f532/discussion-here-mcnpro-box-version-3-3-0-a-1496820/)

Mcnbox 06-27-2012 07:03

★★★★★Discussion here>> Mcnpro Box version 3.3.0 ★★★★★
 
What's new for Mcnpro box version 3.3.0 ? New!! Hot!!


  • Add CoolSand CPU complete supported
    • Read / Write
    • IMEI Change
    • Format
    • Unlock
    • Factory Set
    • Read Code
  • Spreadtrum new Flash ICs added (6610/20)
  • Spreadtrum read/write bugs fixed (6800H)
  • Spreadtrum bootloader improved(880xG)
  • MTK new Rx/Tx pin detection method added
  • MTK read /write bugs fixed (For New CPU)
  • Other small report bugs fixed
    Quote:

    Welcome to use McnBox!
    Selected COM9
    Baud setting ...
    Set Baud done
    Initialize in progress ...
    Checking data ...
    Serial No. MCNxxxxxxxxxxxx
    Firmware V1.15
    Checksum 15B9-21BE
    Software V3.30
    Box Connected!
    Ready working at COM9
    ...



Upgrading from Previous Versions:
As usual, We recommend that all customers running previous versions now upgrade to new version which is available for all customers with valid, To download that from support section , You also can using updater direct upgrade your software online!




Best regards !


Mcnbox Team

pshycoboy 06-27-2012 07:09

nice update mcn team,thx for mcn pro box new update...

medariy 06-27-2012 07:14

thx u for this update.....

Mcnbox 06-27-2012 07:23

Thanks, we hope all customer to report the bugs, post Successfully unlocked/repaired phones by Mcnpro Box at here !


Best regards !

Mcnbox Team

mubashar757 06-27-2012 07:34

thanks good update....................

sandulxxx 06-27-2012 07:41

great update...YOU DO CUSTOMER NEEDED....!!!!

pshycoboy 06-27-2012 07:44

fastpin finder mtk 6253,,so cool...


Welcome to use McnBox!
Selected COM3
Baud setting ...
Set Baud done
Initialize in progress ...
Checking data ...
Serial No.xxxxxxxxxx
Firmware V1.15
Checksum 5BEB-73BE
Software V3.30
Box Connected!
Ready working at COM3
-------------------------------
Start Scanning...
->.....
Results:
CPU: MT6253.
GND:5,RXD:3,TXD:2,BOOT:1
[G:1 5 R:3 T:2] Apply to Box
Press and Holding Power button now !
Connecting, wait...
Phone detected, wait..
CPU: 6253 Ver: 8A04 SW:8A00
Initialize Boot6 ...
Flash(Nor) Type [SPANSION] S29VS128R_T
Flash(Nor) Code 0001007E(00630001)
Flash(Nor) Size 0x01000000 Hex Bytes
Checking baud...
Set Baud:921600 Done.
Start Reading(Nor)...
The phone information:
BVTTECH53_09B_GEMINI_PCB01_GPRS_MT6253_S00.MAUI_09 B_W10_12_MP_V3.BIN_FLNS71VS128RC0AHK4L0
Checksum Error in 00EB4000
File Saved: D:\file china\gvon 677\read mcn


what this error info?this phone normal,just iwant tes this update..

Mj2 06-27-2012 07:53

thanks sir for update,.. fast detect pin and read mtk 6253

Welcome to use McnBox!
Selected COM9
Baud setting ...
Set Baud done
Initialize in progress ...
Checking data ...
Serial No. MCNxxxxx
Firmware V1.15
Checksum Axxx
Software V3.30
Box Connected!
Ready working at COM9
-------------------------------
Start Scanning...
->........
Results:
CPU: MT6253.
GND:10,RXD:3,TXD:1
[G:10 R:3 T:1] Apply to Box
[G:10 R:3 T:1] Apply to Box
Press and Holding Power button now !
Connecting, wait...
Phone detected, wait..
CPU: 6253 Ver: 8A02 SW:8A00
Initialize Boot6 ...
Flash(Nor) Type [TOSHIBA] TC58FYM7T8C
Flash(Nor) Code 0098009E(00000000)
Flash(Nor) Size 0x01000000 Hex Bytes
Checking baud...
Set Baud:921600 Done.
Start Reading(Nor)...
The phone information:
UNISCOPE53_09A_PCB01_GPRS_MT6253_S00.V53B76.BIN_FL NTY6701111184KC
Read Done !
Time used: 4 mins 22 s
File Saved: D:\firmware\Mcn\cross cb 95t\UNISCOPE53_09A_PCB01_GPRS_MT6253_S00.V53B76.BI N_FLNTY6701111184KC
Press and Holding Power button now !
Connecting, wait...
CPUMT6253 Ver: 8A02 SW:8A00
Release Power Button now
Phone detected
Infr: MT6253_V53B76_09A_HW_Melody_V0.0
NV Data saved to: D:\firmware\Mcn\cross cb 95t\NV_MT6253_V53B76_09A_HW_Melody_V0.0
Backup Done.

pshycoboy 06-27-2012 08:00

stop in 91%,,,phone normal,just i want tes and back updata...

http://img837.imageshack.us/img837/6172/16714843.png

pshycoboy 06-27-2012 08:03

Quote:

Originally Posted by Mj2 (Post 8537966)
thanks sir for update,.. fast detect pin and read mtk 6253

Welcome to use McnBox!
Selected COM9
Baud setting ...
Set Baud done
Initialize in progress ...
Checking data ...
Serial No. MCNxxxxx
Firmware V1.15
Checksum Axxx
Software V3.30
Box Connected!
Ready working at COM9
-------------------------------
Start Scanning...
->........
Results:
CPU: MT6253.
GND:10,RXD:3,TXD:1
[G:10 R:3 T:1] Apply to Box
[G:10 R:3 T:1] Apply to Box
Press and Holding Power button now !
Connecting, wait...
Phone detected, wait..
CPU: 6253 Ver: 8A02 SW:8A00
Initialize Boot6 ...
Flash(Nor) Type [TOSHIBA] TC58FYM7T8C
Flash(Nor) Code 0098009E(00000000)
Flash(Nor) Size 0x01000000 Hex Bytes
Checking baud...
Set Baud:921600 Done.
Start Reading(Nor)...
The phone information:
UNISCOPE53_09A_PCB01_GPRS_MT6253_S00.V53B76.BIN_FL NTY6701111184KC
Read Done !
Time used: 4 mins 22 s
File Saved: D:\firmware\Mcn\cross cb 95t\UNISCOPE53_09A_PCB01_GPRS_MT6253_S00.V53B76.BI N_FLNTY6701111184KC
Press and Holding Power button now !
Connecting, wait...
CPUMT6253 Ver: 8A02 SW:8A00
Release Power Button now
Phone detected
Infr: MT6253_V53B76_09A_HW_Melody_V0.0
NV Data saved to: D:\firmware\Mcn\cross cb 95t\NV_MT6253_V53B76_09A_HW_Melody_V0.0
Backup Done.

woooow,,my pc error?ok thx i try againt

leepswit 06-27-2012 08:05

wowwwwwww so very nice update!!!*** job mcn pro team.

Agunk Radical 06-27-2012 08:11

Tested for SPRD3 6800H

Welcome to use McnBox!
Selected COM7 COM6
Baud setting ...
Set Baud done
Initialize in progress ...
Checking data ...
Serial No. MCNxxxxxxxxxxxxx
Firmware V1.15
Checksum ED52-CABE
Software V3.30
Box Connected!
Ready working at COM7
[G:8 9 D-:3 D+:4 Up:12 Down:5] Apply to Box
Checking USB Serial port, wait...
SCI USB2Serial Port: COM8
Connecting, wait...
Phone Connected!
Info: SPRD3
Initialize boot12...
Boot Done.
Flash Type NAND (0)
Start Writing...Code
Write Done!

dj_fenola 06-27-2012 08:14

good news that the wait ...........


always successful MCNPro Team


thanks

umarnlw 06-27-2012 08:54

nice update and keep it more up

DinOlabs 06-27-2012 09:04

great job my bro... thanks to update :)


br,


All times are GMT +1. The time now is 00:29.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2017 -

Page generated in 0.28084 seconds with 5 queries

SEO by vBSEO