|
Discussion and Post Success Stories here>> Mcnpro Box version 3.05 Discussion and Post Success Stories here>> Mcnpro Box version 3.0.5 More news will be coming in those days too Again, thank you to everyone who support US , we sincerely appreciate your assistance - and we hope with this release that will help you around. Thanks Mcnpro customer help for beta test version 3.04 (Not for pulic) Mcnbox E-Mail : [email protected] Yahoo: [email protected] Sonork: 100.76027 |
Some tested post info: http://forum.gsmhosting.com/vbb/7070782-post60.html http://forum.gsmhosting.com/vbb/7070867-post61.html http://forum.gsmhosting.com/vbb/7070913-post62.html Welcome to use McnBox! Selected COM5 Baud setting ... Set Baud done Initialize in progress ... Checking data ... Serial No. MCN************* Firmware V1.09 Checksum 4BE0-**** Box Connected! Ready working at COM5 ================================== Suggest: Power supply with the tran-clamp to read the pin-status Scanning pin-status,please waiting... ->..................................... 13,17,18 Short-pin Pin-status Scan Done ------------------------------- Scanning,waiting... ->=. Operation done, Pin detect out. USB D-: 9 USB D+: 10 Spread Total expend 4 seconds ... Operation done, Pin detect out. BOOT: 7 set as oInvert USB D-: 9 USB D+: 10 GND:8 11 12 16 Press [ Save ] to save Pinout [G:7 8 11 12 16 D-:9 D+:10] Apply to Box If Scan other phone, please click [Stop] [G:8 11 12 16 D-:9 D+:10 oI:7] Apply to Box Checking SCI USB2Serial port, wait... SCI USB2Serial Port: COM8 Connecting, wait... Phone Connected! Info: Spreadtrum Boot Block version 2.0 Initialize boot... Boot Done. Setting baudrate... 921600 Set baud Done CPU Info 6600M/E Flash Type NOR Flash ID 00EC257E(25082501) Flash Model K5L2931CAM Flash Size 0x1000000(16.0M) Start Reading... Read Done! File saved: D:\mcnpro files\6600M_E_K5L2931CAM.bin [G:8 11 12 16 D-:9 D+:10 oI:7] Apply to Box Checking SCI USB2Serial port, wait... SCI USB2Serial Port: COM8 Connecting, wait... Phone Connected! Info: Spreadtrum Boot Block version 2.0 Initialize boot... Boot Done. Setting baudrate... 921600 Set baud Done CPU Info 6600M/E Flash Type NOR Flash ID 00EC257E(25082501) Flash Model K5L2931CAM Flash Size 0x1000000(16.0M) Start Writing... Write Done! |
i hope fix mt6268..wait result my phone with mt6268 succes scan rx/tx now I read fw Selected COM3 COM9 COM14 Baud setting ... Set Baud done Initialize in progress ... Checking data ... Serial No. MCN2************ Firmware V1.09 Checksum 9520-B8BE Box Connected! Ready working at COM3 ------------------------------- Start Scanning... ->..... Results: MTK Chipset CPU: MT6268. GND:5,RXD:3,TXD:2 [G:5 R:3 T:2] Apply to Box |
Boot 6 /7 should be working perfect ! BTW, pls edit your S/N ^_^ |
Start Scanning... ->..... Results: MTK Chipset CPU: MT6268. GND:5,RXD:3,TXD:2 [G:5 R:3 T:2] Apply to Box Comm Error 001:Definitions may be incorrect, to scan again [G:5 R:3 T:2] Apply to Box Press and Holding Power button now ! Connecting, wait... Phone detected, wait.. CPU: 6268 Ver: 8B01 SW:8B01 CPU ID: Initialize Boot4 ... Phone not support on this boot, or cpu dead. select Boot4 or Boot6 [G:5 R:3 T:2] Apply to Box Press and Holding Power button now ! Connecting, wait... Phone detected, wait.. CPU: 6268 Ver: 8B01 SW:8B01 CPU ID: General DA Initialize Boot7 ... Phone no response Error [G:5 R:3 T:2] Apply to Box Press and Holding Power button now ! Connecting, wait... Phone detected, wait.. CPU: 6268 Ver: 8B01 SW:8B01 CPU ID: Initialize Boot6 ... Phone no response Error [G:5 R:3 T:2] Apply to Box Press and Holding Power button now ! Connecting, wait... Phone detected, wait.. CPU: 6268 Ver: 8B01 SW:8B01 CPU ID: Initialize Boot6 ... Phone no response Error look..result sorry I can't edit post maybe you can.. |
Thank for your update brother ;) MCN is the best for chines phone, more update and update :) Br hacell |
Quote:
Keep press power on / release Power + / release USB cable first put the USB cable back then connect Power + Thanks |
Phone detected, wait.. CPU: 6268 Ver: 8B01 SW:8B01 CPU ID: 03EF0B00 Initialize Boot6 ... Flash Type [TOSHIBA] TV00570002CDGB, TC58FVM7TDD Flash(Nor) Code 00980003 Flash(Nor) Size 0x01000000 Hex Bytes Checking baud Set Baud:921600 Done. Start Reading(nor)... ...... I tested ! Mcnbox |
there is something wrong on MCN 3.05 I'M TRY MCN VERSION 3:05 IN PHONE NORMAL TIPE OF PHONE CROSS CB 91 RESULTS OF HIS LIKE THIS Results: CPU: MT6253. VCC:8,GND:10,RXD:3,TXD:1 [V:8 G:10 R:3 T:1] Apply to Box The File Information: UNISCOPE53_09A_PCB01_GPRS_MT6253_S00.V53B26.BIN_FL NTY6701111184KC >> Press and Holding Power button now ! Connecting, wait... Phone detected, wait.. CPU: 6253 Ver: 8A02 SW:8A00 CPU ID: 00000F00 Initialize Boot6 ... Phone not support on this boot, or cpu dead THERE ARE ERRORS IN THIS VERSION TRY OUT MY OTHER TOOL WITH HIS GOOD RESULTS :confused: LOG USING OTHER TOOL Code: Please Hold "ON" to connect with the phone... |
Can you check for boot5 ? and post report. Mcnbox |
success read flash cpu 6225 Welcome to use McnBox! Selected COM15 Baud setting ... Set Baud done Initialize in progress ... Checking data ... Serial No:*******. Firmware V1.09 Checksum 5BEA-72BE Box Connected! Ready working at COM15 ------------------------------- Start Scanning... ->. Results: CPU: MT6225. VCC:1,GND:10,RXD:3,TXD:9,BOOT:2 [V:1 G:10 R:3 T:9 oL:2] Apply to Box Press and Holding Power button now ! Connecting, wait... Phone detected, wait.. CPU: 6225 Ver: 8A05 SW:8A00 CPU ID: 03D70E00 Initialize Boot4 ... Flash(Nor) Type [ST] M30L0T7000T0,M36L0T7050T0 Flash(Nor) Code 002088C4(00000000) Flash(Nor) Size 0x01000000 Hex Bytes Checking baud،* Set Baud:921600 Done. Start Reading(Nor)... The phone information: K420MLT_PCB01_GPRS_MT6225_S00.M_RK4214202_M22202_V 1_0_0_0M0614.BIN Read Done ! Time used: 4 mins 14 s File Saved: D:\China Flash Files.mcn\d610\K420MLT_PCB01_GPRS_MT6225_S00.M_RK4 214202_M22202_V1_0_0_0M0614.BIN ******************************************* ******************************************* *************************************** |
success read flash whith spd SCI USB2Serial Port: COM12 Connecting, wait... User Abort [G:8 10 D-:4 D+:6 oL:2 3 7 9 oI:1 5] Apply to Box Checking SCI USB2Serial port, wait... SCI USB2Serial Port: COM12 Connecting, wait... Press and Holding Power button now ! Checking SCI USB2Serial port, wait... SCI USB2Serial Port: COM12 Connecting, wait... Phone Connected! Info: Spreadtrum Boot Block version 2.0 Initialize boot... CPU Info 6600L/WT6226 Flash Type NOR Flash ID 00EC257E(25062501) Flash Model K5L6331CAM Flash Size 0x800000(8.0M) Start Reading... Read Done! File saved: D:\China Flash Files.mcn\6600L_WT6226_K5L6331CAM.bin |
success read flash and nv ok cpu 6225 Welcome to use McnBox! Selected COM15 Baud setting ... Set Baud done Initialize in progress ... Checking data ... Serial No. MCN********* Firmware V1.09 Checksum 5BEA-72BE Box Connected! Ready working at COM15 ------------------------------- Start Scanning... ->.. Results: CPU: MT6225. VCC:9,GND:5 10,RXD:1,TXD:3 [V:9 G:5 10 R:1 T:3] Apply to Box Press and Holding Power button now ! Connecting, wait... Phone detected, wait.. CPU: 6225 Ver: 8A05 SW:8A00 CPU ID: 03F70E00 Initialize Boot4 ... Flash(Nor) Type [SAMSUNG] K5L2931CAM Flash(Nor) Code 00EC257E(25082501) Flash(Nor) Size 0x01000000 Hex Bytes Checking baud،* Set Baud:921600 Done. Start Reading(Nor)... The phone information: PROWAVE25_GEMINI_PCB01_GPRS_MT6225_S00.A517C_05_LT 3199D2_R1_NO3D.BIN Read Done ! Time used: 4 mins 16 s File Saved: D:\China Flash Files.mcn\q6_java\PROWAVE25_GEMINI_PCB01_GPRS_MT62 25_S00.A517C_05_LT3199D2_R1_NO3D.BIN Press and Holding Power button now ! Connecting, wait... CPU: 6225 Ver: 8A05 CPUID: 03F70E00 Release Power Button now Phone detected Infr: MT6225_A517C_05_LT3199D2_R1.no3d_PROWAVE25_GEMINI_ HW_Melody_V0.0 NV Data saved to: D:\China Flash Files.mcn\q6_java\NV_MT6225_A517C_05_LT3199D2_R1.n o3d_PROWAVE25_GEMINI_HW_Melody_V0.0 Backup Done. |
Quote:
Quote:
->. Results: CPU: MT6253. VCC:8,GND:10,RXD:3,TXD:1 [V:8 G:10 R:3 T:1] Apply to Box Press and Holding Power button now ! Connecting, wait... Phone detected, wait.. CPU: 6253 Ver: 8A02 SW:8A00 CPU ID: 00000F00 Initialize Boot5 ... Boot5 (All Flash),the Boot not support the Phone, or CPU Bad. Select other Boot. :confused: |
My problem is finished with MCN box ... tool box and other it can not complete .. see the results of his log ... read mt6268 Code: Start Scanning...Code: Press and Holding Power button now !fisrt and fast agian running fast then infinity and other box |
| All times are GMT +1. The time now is 20:37. |
vBulletin Optimisation provided by
vB Optimise (Pro) -
vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2023 -