Regarding SPD 6600 Series CPU working with Mcnpro Box - GSM-Forum

**Mcnbox** · 06-03-2009, 08:16

Regarding SPD 6600 Series CPU working with Mcnpro Box. ( of course still very easy to play )

1. All most 6600 Series CPU normal we are using USB Scan detect.

2. If always found "Unknow USB device" etc. which means your operation is wrong , and phone still did not connect well .

3. The Right Operation:

Connect phone via USB cable, put on power cable "+" "-" to phone battery connector via adaptor ( The red and black one, no need battery )
Start to " USB Scan " , No need to power on the phone , holding power on key and press " Read status " , Often we scan 2 times to be sure the scan result which is correct.
Then start to find " charge Pin " ( The operate Just follow the window , detect each pin we 'd better waiting 10s ).
Other option of the delaytime, normal i setting to 800 , which is Phone power on delayed time .
Finish those step , We can press " Start " to Scan phone now .
After Computor will be tell you found new device and start to install driver. then can Apply the scan result.

4. Finish Scan , then you can doing Flash , Unlock etc.

if you can have problem , Please post here , let's help you around !

Best Regards !

Mcnbox Team.

elhadjioumar · 06-03-2009, 13:04

Quote:

Originally Posted by Mcnbox

Regarding SPD 6600 Series CPU working with Mcnpro Box. ( of course still very easy to play )

1. All most 6600 Series CPU normal we are using USB Scan detect.

2. If always found "Unknow USB device" etc. which means your operation is wrong , and phone still did not connect well .

3. The Right Operation:

Connect phone via USB cable, put on power cable "+" "-" to phone battery connector via adaptor ( The red and black one, no need battery )
Start to " USB Scan " , No need to power on the phone , holding power on key and press " Read status " , Often we scan 2 times to be sure the scan result which is correct.
Then start to find " charge Pin " ( The operate Just follow the window , detect each pin we 'd better waiting 10s ).
Other option of the delaytime, normal i setting to 800 , which is Phone power on delayed time .
Finish those step , We can press " Start " to Scan phone now .
After Computor will be tell you found new device and start to install driver. then can Apply the scan result.

4. Finish Scan , then you can doing Flash , Unlock etc.

if you can have problem , Please post here , let's help you around !

Best Regards !

Mcnbox Team.

ok after scan i install corectly the drivers but the optons of spd stay inactive on the soft .I cannot read or unlock ......what is wrong ?

**PhoneCareCenter** · 06-03-2009, 14:15

@elhadjioumar

Try Using the Latest Version of McnPro Software, also try to Scan TX - RX on some SpreadTrum CPU's to solve your problem, if detected, then continue with Unlock, Format, Flash Options....

Good Luck

kcponsel · 05-09-2010, 10:05

hello sir, i'm new in mcnbow user

i confuse about using mcn to find pin, read and format for spreadtrum cpu

i have read your explaination

about "connect phone via usb cable" this cable , you mean service cable?

i find all my cable for service cable jack, no usb cable or i must buy for it?

thanks

**Mcnbox** · 05-09-2010, 12:31

Quote:

Originally Posted by kcponsel

hello sir, i'm new in mcnbow user

i confuse about using mcn to find pin, read and format for spreadtrum cpu

i have read your explaination

about "connect phone via usb cable" this cable , you mean service cable?

i find all my cable for service cable jack, no usb cable or i must buy for it?

thanks

Yes, the cable is service cable from Mcnpro Package, eg, 35-C14C.

Best regards !

Mcnbox

kcponsel · 05-10-2010, 04:57

sir, i have done as you told, but after the program found usb d+ and usb d-

the 'unlock, format, read, and flash' icons become hidden

whats wrong? thanks

**Mcnbox** · 05-10-2010, 10:37

Quote:

Originally Posted by kcponsel

sir, i have done as you told, but after the program found usb d+ and usb d-

the 'unlock, format, read, and flash' icons become hidden

whats wrong? thanks

Post here your scan result !

A,) After pinout detect ,then Apply it to Box
B,) The sametime you can see the software interface near bottom right corner, the COM port get changed. and in computer device management control panel there have other port named "SCI USB2Serial" port too.
C,) Then do what you wanna to do for your phone

Best regards !

Mcnbox

sobujkhan · 05-10-2010, 19:14

Hello sir pls tell ,me when i scan usb scan he new hardware but whice driver i selected spd cpu she auto install driver pls hellp me

**Mcnbox** · 05-10-2010, 21:00

Quote:

Originally Posted by sobujkhan

Hello sir pls tell ,me when i scan usb scan he new hardware but whice driver i selected spd cpu she auto install driver pls hellp me

So what's your problem ?

A), Driver at C:\Program Files\Mcnbox Team\Mcnpro Box\Drivers\Mobile divers
B), Just choose this folder then install

Any problem , post here , we will help around , don't worry !

Best regards !

Mcnbox

Jatnick · 05-13-2010, 04:47

Quote:

Originally Posted by Mcnbox

Regarding SPD 6600 Series CPU working with Mcnpro Box. ( of course still very easy to play )

1. All most 6600 Series CPU normal we are using USB Scan detect.

2. If always found "Unknow USB device" etc. which means your operation is wrong , and phone still did not connect well .

3. The Right Operation:

Connect phone via USB cable, put on power cable "+" "-" to phone battery connector via adaptor ( The red and black one, no need battery )
Start to " USB Scan " , No need to power on the phone , holding power on key and press " Read status " , Often we scan 2 times to be sure the scan result which is correct.
Then start to find " charge Pin " ( The operate Just follow the window , detect each pin we 'd better waiting 10s ).
Other option of the delaytime, normal i setting to 800 , which is Phone power on delayed time .
Finish those step , We can press " Start " to Scan phone now .
After Computor will be tell you found new device and start to install driver. then can Apply the scan result.

4. Finish Scan , then you can doing Flash , Unlock etc.

if you can have problem , Please post here , let's help you around !

Best Regards !

Mcnbox Team.

try to phonelock maxtron mg-168 but unsuccessful... phone driver was detectd, read phone is ok, but cant to open phone lock code..(cpu spd 6600R)..how to solve?

thanks..

**Mcnbox** · 05-13-2010, 11:52

Quote:

Originally Posted by Jatnick

try to phonelock maxtron mg-168 but unsuccessful... phone driver was detectd, read phone is ok, but cant to open phone lock code..(cpu spd 6600R)..how to solve?

thanks..

Post Any logs?

Mcnbox

Jatnick · 05-13-2010, 13:05

Quote:

Originally Posted by Mcnbox

Post Any logs?

Mcnbox

Scan Pinout
---------------
Welcome to use McnBox!
Selected COM11 COM12 COM10 COM7
Initialize in progress...
Checking data, wait...
Serial number: MCN2009xxxxxxxxxxxxxxxx
Firmware version: V1.06
Checksum value: 2E95-0DBE
Box Connected!
Box Operating at high speed port: COM12
[G:1 5 10 11 12 13 18 D-:9 D+:8] Apply to Box

Format
-------------
Formatting, Please Power Off & On
Start connecting, wait
Boot Info:
Initialize Boot...
CPU : 6600R
Flash(Nand) CODE: 00AD0076
Flash(Nand) Type: NF_HY27XS08121M
Flash(Nand) Size: 04200000

Read
------------
Start connecting, wait
Boot Info:
Initialize Boot...
CPU : 6600R
Flash(Nand) CODE: 00AD0076
Flash(Nand) Type: NF_HY27XS08121M
Flash(Nand) Size: 04200000
Completed

Unlock
-----------
cant unlock... sory log unlock i forget to save....

**PhoneCareCenter** · 05-13-2010, 15:27

@Jatnick

If u used the New Method, your File will still be in McnPro Folder in the Programmes Folder of your Hard Disk (Where McnPro is Installed).. Just add the file and Press Unlock..

McnPro Team

Jatnick · 05-14-2010, 12:08

Quote:

Originally Posted by PhoneCareCenter

@Jatnick

If u used the New Method, your File will still be in McnPro Folder in the Programmes Folder of your Hard Disk (Where McnPro is Installed).. Just add the file and Press Unlock..

McnPro Team

still not open phonelock code

**Mcnbox** · 05-14-2010, 13:25

Quote:

Originally Posted by Jatnick

still not open phonelock code

I checked today , 6600R have some bugs, this problem should be fixed at next version .

Mcnbox

06-03-2009, 08:16	#1 (permalink)
Mcnbox Product Manager Join Date: Mar 2008 Posts: 1,891 Member: 726283 Status: Offline Sonork: 100.76027 Thanks Meter: 7,616	Regarding SPD 6600 Series CPU working with Mcnpro Box Regarding SPD 6600 Series CPU working with Mcnpro Box. ( of course still very easy to play ) 1. All most 6600 Series CPU normal we are using USB Scan detect. 2. If always found "Unknow USB device" etc. which means your operation is wrong , and phone still did not connect well . 3. The Right Operation: Connect phone via USB cable, put on power cable "+" "-" to phone battery connector via adaptor ( The red and black one, no need battery ) Start to " USB Scan " , No need to power on the phone , holding power on key and press " Read status " , Often we scan 2 times to be sure the scan result which is correct. Then start to find " charge Pin " ( The operate Just follow the window , detect each pin we 'd better waiting 10s ). Other option of the delaytime, normal i setting to 800 , which is Phone power on delayed time . Finish those step , We can press " Start " to Scan phone now . After Computor will be tell you found new device and start to install driver. then can Apply the scan result. 4. Finish Scan , then you can doing Flash , Unlock etc. if you can have problem , Please post here , let's help you around ! Best Regards ! Mcnbox Team.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How is working OM CPU with Mcnpro Box >>	Mcnbox	McnPro Box	0	07-19-2009 10:08
<< How is working Anyka CPU with Mcnpro Box	Mcnbox	McnPro Box	0	07-04-2009 10:40
How is working Spreadtrum CPU with Mcnpro Box >>	Mcnbox	McnPro Box	2	06-30-2009 18:17
How is working ADI Chips with McnPro Box >>	Mcnbox	McnPro Box	17	06-05-2009 14:58
How is working INFINEON Chips with McnPro Box >>	Mcnbox	McnPro Box	0	06-02-2009 08:32

06-03-2009, 14:15	#3 (permalink)
PhoneCareCenter Product Manager Join Date: Aug 2007 Location: Inside Java Posts: 1,187 Member: 574123 Status: Offline Sonork: 100.1581804 Thanks Meter: 1,839	@elhadjioumar Try Using the Latest Version of McnPro Software, also try to Scan TX - RX on some SpreadTrum CPU's to solve your problem, if detected, then continue with Unlock, Format, Flash Options.... Good Luck

05-09-2010, 10:05	#4 (permalink)
kcponsel Insane Poster Join Date: Apr 2005 Age: 47 Posts: 71 Member: 134922 Status: Offline Thanks Meter: 3	hello sir, i'm new in mcnbow user i confuse about using mcn to find pin, read and format for spreadtrum cpu i have read your explaination about "connect phone via usb cable" this cable , you mean service cable? i find all my cable for service cable jack, no usb cable or i must buy for it? thanks

05-10-2010, 04:57	#6 (permalink)
kcponsel Insane Poster Join Date: Apr 2005 Age: 47 Posts: 71 Member: 134922 Status: Offline Thanks Meter: 3	sir, i have done as you told, but after the program found usb d+ and usb d- the 'unlock, format, read, and flash' icons become hidden whats wrong? thanks

05-10-2010, 19:14	#8 (permalink)
sobujkhan Insane Poster Join Date: Jul 2006 Posts: 71 Member: 315793 Status: Offline Thanks Meter: 1	Hello sir pls tell ,me when i scan usb scan he new hardware but whice driver i selected spd cpu she auto install driver pls hellp me

05-13-2010, 15:27	#13 (permalink)
PhoneCareCenter Product Manager Join Date: Aug 2007 Location: Inside Java Posts: 1,187 Member: 574123 Status: Offline Sonork: 100.1581804 Thanks Meter: 1,839	@Jatnick If u used the New Method, your File will still be in McnPro Folder in the Programmes Folder of your Hard Disk (Where McnPro is Installed).. Just add the file and Press Unlock.. McnPro Team