1280 after flash phone same condition

[SAN INFOTECH]

1280 AFTER FLASH PHONE IS NOT

Using device: UFS_USB V2.8 (c) SarasSoft 2007.
Library version: 1.0.0.9019(20-11-2010), 1.0.0.15042(20-11-2010)
Do not disconnect or abort this operation otherwise phone will be damaged.
Device synchronized.
CPU ID: A200341100 [X-GOLD 110]
Sending Primary Boot Loader ...OK
Changing baudrate to: 921600
Sending Secondary Boot Loader ...OK
BootloaderString: SE0_091125  F11
Boot mode: CC
EBL version: 10.13, Default_RAM_Bootloader
Flash ID: 00EC 2254 [Samsung K8S6415ETC,64 Mbits]
Processing CODE:hw_b2_rm647_r05.800.fls from file rm647_005.800
Erasing area 0x00800000-0x00A0FFFE ...OK
Programming ...
Programming completed in 36.579 s
Erasing area 0x00C60000-0x00EAFFFE ...OK
Programming ...
Programming completed in 36.250 s
Erasing area 0x00FFC000-0x00FFFFFE ...OK
Programming ...
Programming completed in 0.047 s
Checksum OK (0x5864)
Processing CUST:hw_b2_rm647_005.80mr.fls from file rm647_005.80mr
Erasing area 0x00210000-0x0045FFFE ...OK
Programming ...
Programming completed in 20.078 s
Checksum OK (0xC478)
Processing CUST:hw_b2_rm6470_nai05.80mr.fls from file rm6470_nai05.80mr
Erasing area 0x00EB0000-0x00F7FFFE ...OK
Programming ...
Programming completed in 5.453 s
Checksum OK (0xFBF7)
Flashing completed in 2 min 29.157 s
 
Phone Type: RM-647 
SW Version: V 05.80 06-08-10 RM-647 (c) Nokia 
Imei plain: 35377904466180-1
Product Code: 0592282
Cellular System: GSM
ASIC ID: 0x2292, type: 11
Ppm Id: MR
Language Pack:
- not available.

 
Imei net: 35377904466180
Version: 
Provider: GSM Test Operator, Country: -
Counter: 0/3, 0/10
 
CONFIG_DATA: 0010100000000000
PROFILE_BITS: 0000000000030002
 
BLOCK 1:   1.OPEN 2.OPEN 3.OPEN 4.OPEN 5.OPEN
BLOCK 2:   1.OPEN 2.OPEN 3.OPEN 4.OPEN 5.OPEN
BLOCK 3:   1.OPEN 2.OPEN 3.OPEN 4.OPEN 5.OPEN
BLOCK 4:   1.OPEN 2.OPEN 3.OPEN 4.OPEN 5.OPEN
BLOCK 5:   1.OPEN 2.OPEN 3.OPEN 4.OPEN 5.OPEN
BLOCK 6:   1.OPEN 2.OPEN 3.OPEN 4.OPEN 5.OPEN
BLOCK 7:   1.OPEN 2.OPEN 3.OPEN 4.OPEN 5.OPEN

[sajidshah50]

Bro 1st check lcd ways.....if ok then change the lcd

[gbluez]

hi,
from the logs above all goes fine.
most case:
- you will need to check also lighting issue on lcd. how to make jumper many discussed @ hardware sub forum.



BR