mobole EX v3.5 rev2.3 not Boot DCT4

[maxpro12]

This phone is 100% good and working but MX box not Boot

MX team, Please solved the problem

MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 4], SN: xxxxxxxxxxx
Using device: HTI, FW ver: 00.50, SN:xxxxxxxxx
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.21151(13-07-2012), Library ver: 1.0.0.14195(13-07-2012)
Boot error: CC CC CC 00
- Repeat the procedure. Sometimes it is a matter of temporary communication problem or similar.
- Check that all used cable are solid without any visible damage and have good contact. If possible, try with other cables.
- On rare occasions phone might be damaged or dead. So, if possible, try with another phone.

[Teknotel-GSM]

DCT4 & DCT3 Always Problem Not Flashing on MxBox

[dipok]

1st check cable
then
upgrade your HTI firmware

[Hamidshah07]

Not working with this @dipok , i always face problem with mx key...but on thing with windows 7 mxkey working best.....

[nulled]

MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 4], SN: xxxxxxxx
Using device: HTI, FW ver: 00.50, SN: xxxxxxxx
Connection status: EHCI:HUB:HUB:HUB:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.21200(18-07-2012), Library ver: 1.0.0.14205(18-07-2012)
ASIC ID: 0x2292 [UPPCosto ver: 1.3]
SecondaryBoot: u3_2nd.fia [DCT4] version: 4.76.0 revision: 0.7 size: 0x9A8
Supported Ids: 3040, 2292, 2293, 3162, 3166, 3168
FlashID0: 0001 327E [AMD S29NS128P,128 Mbits] page size: 128 K type: NOR area: 01000000-01FFFFFF
FlashID1: 0000 0001 [unused/removed]
ExtBUSC: AD7E B61A 1BBE 0BE2 7D58 6BE4 DBEE 6514
Algorithm: u3_amd.fia [DCT4 ALGORITHM] version: 4.76.0 revision: 0.7 size: 0x78C0
Supported Ids: 3040, 2292, 2293, 3162, 3166, 3168
Performing Flash Authentication ...OK
UEM ID: 001943ACA3BDA66
ASIC type: 11
UEM Imei: 35416202576364
Flash Imei: 35416202576364
RPL saved to "E:\mobileEx\3.5\data\backup\RPL\35416202576364_BA CK.rpl"
Processing MCU file: rm305_05.910
[DCT4,DCT4 ALGORITHM] size: 2.34 MB
Supported Ids: 2292
ASIC ID: 0x2292 [UPPCosto ver: 1.3]
SecondaryBoot: u3_2nd.fia [DCT4] version: 4.76.0 revision: 0.7 size: 0x9A8
Supported Ids: 3040, 2292, 2293, 3162, 3166, 3168
FlashID0: 0001 327E [AMD S29NS128P,128 Mbits] page size: 128 K type: NOR area: 01000000-01FFFFFF
FlashID1: 0000 0001 [unused/removed]
ExtBUSC: AD7E B61A 1BBE 0BE2 7D58 6BE4 DBEE 6514
Algorithm: u3_amd.fia [DCT4 ALGORITHM] version: 4.76.0 revision: 0.7 size: 0x78C0
Supported Ids: 3040, 2292, 2293, 3162, 3166, 3168
Performing Flash Authentication ...OK
UEM ID: 001943AC:2984DA60
Area [01000000-0100FFFF] erased in 0.969 s
Area [01010000-0179FFFF] erased in 47.750 s
Area [017A0000-017EFFFF] erased in 2.531 s
Area [01F00000-01FDFFFF] erased in 6.735 s
Flash programming ...
Programming completed in 1 min 16.313 s

[nathan111284]

nice feedback but working fine with me....

[.::MASTER ALONE::.]

Originally Posted by maxpro12

This phone is 100% good and working but MX box not Boot

MX team, Please solved the problem

MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 4], SN: xxxxxxxxxxx
Using device: HTI, FW ver: 00.50, SN:xxxxxxxxx
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.21151(13-07-2012), Library ver: 1.0.0.14195(13-07-2012)
Boot error: CC CC CC 00
- Repeat the procedure. Sometimes it is a matter of temporary communication problem or similar.
- Check that all used cable are solid without any visible damage and have good contact. If possible, try with other cables.
- On rare occasions phone might be damaged or dead. So, if possible, try with another phone.

Always select Correct boot loader.

BR.
Arsalan gsm2000.