Nokia 5130 flashing errors.... ## (ANSWERED) - GSM-Forum

hermanpatel_14 · 09-24-2011, 10:02

Dear Friend,
i have nokia5130 rm495 trying flash the fone with MxKey and cloudn't flash them with fbus nor usb. plz help me by lookin the errors shown below.

LOG of fone flashed with FBUS CABLE

Quote:

MXKEY Serial: [FT SCR2000 0] - C0819513
Using device: UFS_USB V2.8 (c) SarasSoft 2007.
Connection status: OHCI:HUB:HUB:USB 1.10 (Full-speed)
Driver: UFS2XX, ver: 3.1.5.0 , NTMP ver: 2.4.16.0
Module ver: 1.0.0.18624(06-08-2011), Library ver: 1.0.0.12274(06-08-2011)
CMT Data :
SYSTEM ASIC ID: 000000010000022600010006030C192101033000 [RAP3G ver: PA 3.x]
EM0 ID: 00000296
EM1 ID: 00000B22
PUBLIC ID: 2A50010FBCED8C56C2808812664CDEC0B3E29B65
ASIC MODE ID: 00
ROOT KEY HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723
ROM ID: 273F6D55DFAAF68F
SecondaryBoot: RAP3Gv3_2nd.fg [BB5] version: 1.30.0 revision: 0.0 size: 0x3C00
Supported Ids: 0103192101003000, 010C192101003000, 0103192101013000, 010C192101013000, 0103192101003100, 010C192101003100, 0303192101023000, 030C192101023000, 0303192101033000, 030C192101033000, 0103192101001101, 010C192101001101, 0003192101001002, 000C192101001002, 0013192101001002, 001C192101001002
eBB5ProtocolType: OLD
Storage0: 00EC 2400 - 0000 8A31 [Samsung ] type: FLASH,NOR, asic:CMT
Storage content: 0000 0000 0000 0000 0000 0000 0000 0000
Storage1: FFFF 0000 - 0000 0000 type: MMC, asic:CMT
TransmissionMode: 16Bit
Algorithm: RAP3Gv3_algo.fg [BB5 ALGORITHM] version: 1.40.0 revision: 0.0 size: 0x22C10
Supported Ids: 0103192101003000, 010C192101003000, 0103192101013000, 010C192101013000, 0103192101003100, 010C192101003100, 0303192101023000, 030C192101023000, 0303192101033000, 030C192101033000, 0003192101002000, 000C192101002000, 0003192101002100, 000C192101002100, 0003192101002200, 000C192101002200, 0003192101012200, 000C192101012200, 0103192101001101, 010C192101001101, 0003192101001002, 000C192101001002, 0013192101001002, 001C192101001002
CMT PAPUBKEYS is blank/erased.
TransmissionMode: DDR&TX2
Processing MCU file: rm495__07.97.mcusw
[BB5,BB5 ALGORITHM] size: 18.20 MB
Supported Ids: 010C192101013000, 0103192101003000, 0303192101033000, 030C192101033000
Storing certificate [NPC, VARIANT, R&D, CCC, HWC] ...OK
Erase size: 21 MB
CMT FLASH,NOR area [00000000-000006BF]
CMT FLASH,NOR area [000006C0-0001FFFF]
CMT FLASH,NOR area [00040000-000BFFFF]
CMT FLASH,NOR area [000C0000-0013FFFF]
CMT FLASH,NOR area [00140000-0137FFFF]
CMT FLASH,NOR area [01380000-0151FFFF]
erased in 5.859 s
Prog.status for Asic CMT ...
NOR: Success
Flash programming ...
CMT NOLO block sent
CMT KEYS block sent
CMT PRIMAPP block sent
CMT PASUBTOC block sent
Selecting first CMT PAPUB block with matching RootKey.
Error chk C7012D0103CD000010000000F1
RX2 not responding, please check BSI/cable/pinout !
Error while programming [00] at 0x000582C0, Result: 0010
Total time for flashing process(boot+erase+write) was 15.922 s

LOG of fone flashed with usb cable

Quote:

MXKEY Serial: [FT SCR2000 0] - C0819513
Connection status: OHCI:HUB::USB 2.00 (Full-speed)
Driver: NMWCD, ver: 7.1.32.67
Module ver: 1.0.0.18624(06-08-2011), Library ver: 1.0.0.12274(06-08-2011)
Processing MCU file: rm495__07.97.mcusw
[BB5,BB5 ALGORITHM] size: 18.20 MB
Supported Ids: 010C192101013000, 0103192101003000, 0303192101033000, 030C192101033000
Make sure USB cable, Battery and charger are removed from device.
Insert USB cable, Battery back to device(make sure to have fully charged battery).
Insert Charger or Press phone's power button(if flashing doesnt start automatically)
Waiting for USB device ...
Device connected: nmwcdnsuc\Nokia USB Flashing Generic, PORT_ID: DA6EEA6
CMT SYSTEM ASIC ID: 000000010000022600010006030C192101033000 [RAP3G ver: PA 3.x]
CMT EM0 ID: 00000296
CMT EM1 ID: 00000B22
CMT PUBLIC ID: 2A50010FBCED8C56C2808812664CDEC0B3E29B65
CMT ASIC MODE ID: 00
CMT ROOT KEY HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT ROM ID: 273F6D55DFAAF68F
Flashing CMT Update Server Data, ULO: 0x3900 bytes
Update Server code succesfully sent to phone.
Flashing CMT Update Server Data, UPDAPP: 0x4B340 bytes
Update Server code succesfully sent to phone.
Flashing CMT Update Server Data, PASUBTOC: 0x59940 bytes
Update Server code succesfully sent to phone.
Waiting for USB device removal ...OK
Waiting for USB device arrival ...OK
Device connected: nmwcdnsuc\Nokia USB Flashing Generic, PORT_ID: DA6EEA6
Verifying communication to device...
ERROR: Could not verify communication !
Failed to set phone to flashmode, possible reason: Update Agent not running or PASUBTOC corrupted !
Please recover phone using FBUS.

aravindanav · 09-24-2011, 10:08

it is water damage phone cpu some heat

hermanpatel_14 · 09-24-2011, 10:20

No sir It is not water damage fone. Fone was found OFF while customer got up in the morning. Even the PCB is neat and clean. doesn't have any waterdamage or any other kind of damage to it.

destinyhammed · 09-24-2011, 14:40

Selecting first CMT PAPUB block with matching RootKey.
Error chk C7012D0103CD000010000000F1
RX2 not responding, please check BSI/cable/pinout !
Error while programming [00] at 0x000582C0, Result: 0010
Total time for flashing process(boot+erase+write) was 15.922 s

i had the same error with 3 different phone 2 nokia 2700c and 1 nokia 5130 and after this error the phone was unable to take flash again even with infinity best dongle unable to revive the phone urgent solution needed from mxkey supporter

gbluez · 09-24-2011, 20:14

- you have to be SURE that the cable you are using is GOOD WORKING.
that error indicates bad cable.

- don't say any cable brand. the famous one are ***** now - GxG
- don't say about beast dongle here.

BR

chandan_123 · 09-24-2011, 21:05

try to another box then hardware bro...........

hermanpatel_14 · 09-30-2011, 14:07

dude tried it with Universal box, HWK, fenix and also with JAF.....
plz dear friends indeed we need solution for this freeking error.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Seeking for flash nokia 5110 old version (3 version) can exchange for new	Tomas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	10-14-2017 19:29
New Nokia Software!!!!!!!	Jefferson	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	52	12-30-2016 08:17
Need software upgrade for Nokia 5110	ptkrf	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	30	02-24-2016 10:21

09-24-2011, 10:08	#2 (permalink)
aravindanav Freak Poster Join Date: May 2011 Location: ettumanoor Posts: 358 Member: 1587303 Status: Offline Thanks Meter: 42	it is water damage phone cpu some heat

09-24-2011, 10:20	#3 (permalink)
hermanpatel_14 Freak Poster Join Date: Nov 2008 Location: surat Age: 45 Posts: 138 Member: 894345 Status: Offline Thanks Meter: 27	No sir It is not water damage fone. Fone was found OFF while customer got up in the morning. Even the PCB is neat and clean. doesn't have any waterdamage or any other kind of damage to it.

09-24-2011, 14:40	#4 (permalink)
destinyhammed Freak Poster Join Date: Nov 2007 Location: btw testpoint and cpu Posts: 229 Member: 634275 Status: Offline Sonork: 100.1619208 Thanks Meter: 27	Selecting first CMT PAPUB block with matching RootKey. Error chk C7012D0103CD000010000000F1 RX2 not responding, please check BSI/cable/pinout ! Error while programming [00] at 0x000582C0, Result: 0010 Total time for flashing process(boot+erase+write) was 15.922 s i had the same error with 3 different phone 2 nokia 2700c and 1 nokia 5130 and after this error the phone was unable to take flash again even with infinity best dongle unable to revive the phone urgent solution needed from mxkey supporter

09-24-2011, 20:14	#5 (permalink)
gbluez No Life Poster Join Date: Jul 2004 Posts: 11,049 Member: 73565 Status: Offline Thanks Meter: 5,062	- you have to be SURE that the cable you are using is GOOD WORKING. that error indicates bad cable. - don't say any cable brand. the famous one are ***** now - GxG - don't say about beast dongle here. BR

09-24-2011, 21:05	#6 (permalink)
chandan_123 No Life Poster Join Date: Jun 2008 Location: india Posts: 2,541 Member: 801212 Status: Offline Sonork: 100.1657902 Thanks Meter: 773	try to another box then hardware bro...........

09-30-2011, 14:07	#7 (permalink)
hermanpatel_14 Freak Poster Join Date: Nov 2008 Location: surat Age: 45 Posts: 138 Member: 894345 Status: Offline Thanks Meter: 27	dude tried it with Universal box, HWK, fenix and also with JAF..... plz dear friends indeed we need solution for this freeking error.