K608i cid 49 dead - GSM-Forum

pfeilmayer · 12-17-2005, 11:13

hi
I have a k608i cid 49 and after I read codes and replaced certificate from brown to red, phone does not power on and ... I can't do anything with it. I have the following error when I connect the phone (with tp, of course) :
OTP CID: 49
Analyzing configuration...
Failed!
BATTERY VOLTAGE OR USB TRANSFER SIZE MAY BE TOO LOW!

I receive these errors when I try to replace colors, unlock rsa .............

Script error: TSerialPort is not opened
Applet error: ERROR|GetFlashInfo|
Applet error: ERROR GETTING THE FIRST FLASHDEVICE
Error uploading applet

what can I do ?
on support there are no flash files ....
I tryed USB SmART but I only get errors

... but one of the errors I receive it something like : no certificate found (or something) please use recovery ....
and of course whe I try recovery I get error ....
Cruiser Isn't helping me at all .....
any ideas ?

muppet · 12-17-2005, 11:19

You are probably using a phone with a dead battery.
Use a fully charged battery and see if that helps.

elvir003 · 12-17-2005, 11:53

after unkock always turn the primary cid back

pfeilmayer · 12-17-2005, 12:23

the problem is not the battery. I have 2 full charged batteries. the same problem
Ihave also turned back cid49red after reading codes. that is the moment when the phone died.
any other ideas ?

BesTCooL · 12-17-2005, 13:37

UNcheck "analyze configuraiton"
---------------------------------
after upload GDFS...................

pfeilmayer · 12-17-2005, 13:47

Quote:

Originally Posted by BesTCooL

UNcheck "analyze configuraiton"
---------------------------------
after upload GDFS...................

and where can I find GDFS for k608i. on support I found only for k600i cid36 and cid 37 .. I don't have gdfs for cid 49 .. If you have that file please upload it or please send it to : [email protected]
thank you

BesTCooL · 12-18-2005, 01:37

no problem GDF u can upload K608i cıd36 GDFS...

Spiralman · 12-18-2005, 10:42

Yesterday i got 8 pieces of K608i to unlock so when i try them with Cruiser 7.10 i got "connect the testpint" then bla-bla then "disconnect the testpoint" and immediately after that "All threads terminated" so even can't disconnect the testpoint because all closed right after disconnect message... I read that 7.10 have some bugs with K608 so decided to try unlock with GTI New Arm Inside software... Read info. Ok. I press button Unlock - 3 seconds and my K608i is unlocked and all unlock-relock codes are here! WAW!
BUT 2 of them can't be unlocked with GTI it gives me error something like "Wrong model selected or maybe repair needed..." So i try them with Cruiser with 3 latest versions and have error after connect the testpoint message like "Can't read baseband chip ID" and then software freezes.

PS I know that i have to post log from Cruiser but...

pfeilmayer · 12-18-2005, 10:55

@ BestCool
I've tryed to write GDFS from k600i cid 36 but at 12% I receive an error (something like it cannot write at adress "xx xx xx xx xx xx xx" ...) and at 18% it stops with some other error ..... I will try again monday and post here the error messages ...
can the flash be damaged ?!
thank you

BesTCooL · 12-18-2005, 19:40

U use full batery or use external power supply and downgrade baudrate use 460800 or 230400....... try again...

I dont think Flash damaged...

elvir003 · 12-19-2005, 09:56

early this morning unlocked 15 k608 cid 49
no problems
please check hardwear;charging etc.

12-17-2005, 11:13	#1 (permalink)
pfeilmayer Freak Poster Join Date: Aug 2005 Location: Romania Age: 38 Posts: 138 Member: 175146 Status: Offline Thanks Meter: 6	K608i cid 49 dead hi I have a k608i cid 49 and after I read codes and replaced certificate from brown to red, phone does not power on and ... I can't do anything with it. I have the following error when I connect the phone (with tp, of course) : OTP CID: 49 Analyzing configuration... Failed! BATTERY VOLTAGE OR USB TRANSFER SIZE MAY BE TOO LOW! I receive these errors when I try to replace colors, unlock rsa ............. Script error: TSerialPort is not opened Applet error: ERROR\|GetFlashInfo\| Applet error: ERROR GETTING THE FIRST FLASHDEVICE Error uploading applet what can I do ? on support there are no flash files .... I tryed USB SmART but I only get errors ... but one of the errors I receive it something like : no certificate found (or something) please use recovery .... and of course whe I try recovery I get error .... Cruiser Isn't helping me at all ..... any ideas ?

12-17-2005, 11:53	#3 (permalink)
elvir003 Insane Poster Join Date: Dec 2005 Location: Sarajevo Age: 49 Posts: 70 Member: 206034 Status: Offline Thanks Meter: 0	back cid49 red after unkock always turn the primary cid back

12-19-2005, 09:56	#11 (permalink)
elvir003 Insane Poster Join Date: Dec 2005 Location: Sarajevo Age: 49 Posts: 70 Member: 206034 Status: Offline Thanks Meter: 0	check hardwear early this morning unlocked 15 k608 cid 49 no problems please check hardwear;charging etc.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
K608i CID 49 RED Dead	SatMovil	Cruiser Suite	14	06-26-2006 18:19
k608i cid 49 dead	rachelyna	Cruiser Suite	1	04-15-2006 11:48
k608i cid 49 dead with hwk	softel2004	HWK	2	03-09-2006 07:48
K608i cid 49 dead..::Zulea When is the update::..	Keke	SonyEricsson (USB-Smart)	10	01-23-2006 08:06
this is k608i cid 49, is unlock with usb-dongle^?	mighel	SonyEricsson (USB-Smart)	4	10-08-2005 01:03

12-17-2005, 11:19	#2 (permalink)
muppet No Life Poster Join Date: Oct 2003 Location: Auckland, New Zealand Posts: 3,034 Member: 42570 Status: Offline Thanks Meter: 11	You are probably using a phone with a dead battery. Use a fully charged battery and see if that helps.

12-17-2005, 12:23	#4 (permalink)
pfeilmayer Freak Poster Join Date: Aug 2005 Location: Romania Age: 38 Posts: 138 Member: 175146 Status: Offline Thanks Meter: 6	the problem is not the battery. I have 2 full charged batteries. the same problem Ihave also turned back cid49red after reading codes. that is the moment when the phone died. any other ideas ?

12-17-2005, 13:37	#5 (permalink)
BesTCooL No Life Poster Join Date: Dec 2002 Location: TURKEY Age: 44 Posts: 3,285 Member: 18442 Status: Offline Sonork: 111110 Thanks Meter: 622	UNcheck "analyze configuraiton" --------------------------------- after upload GDFS...................

12-18-2005, 01:37	#7 (permalink)
BesTCooL No Life Poster Join Date: Dec 2002 Location: TURKEY Age: 44 Posts: 3,285 Member: 18442 Status: Offline Sonork: 111110 Thanks Meter: 622	no problem GDF u can upload K608i cıd36 GDFS...

12-18-2005, 10:42	#8 (permalink)
Spiralman Freak Poster Join Date: Sep 2004 Location: Kosovo, Pristina Age: 42 Posts: 120 Member: 83335 Status: Offline Thanks Meter: 1	Yesterday i got 8 pieces of K608i to unlock so when i try them with Cruiser 7.10 i got "connect the testpint" then bla-bla then "disconnect the testpoint" and immediately after that "All threads terminated" so even can't disconnect the testpoint because all closed right after disconnect message... I read that 7.10 have some bugs with K608 so decided to try unlock with GTI New Arm Inside software... Read info. Ok. I press button Unlock - 3 seconds and my K608i is unlocked and all unlock-relock codes are here! WAW! BUT 2 of them can't be unlocked with GTI it gives me error something like "Wrong model selected or maybe repair needed..." So i try them with Cruiser with 3 latest versions and have error after connect the testpoint message like "Can't read baseband chip ID" and then software freezes. PS I know that i have to post log from Cruiser but...

12-18-2005, 10:55	#9 (permalink)
pfeilmayer Freak Poster Join Date: Aug 2005 Location: Romania Age: 38 Posts: 138 Member: 175146 Status: Offline Thanks Meter: 6	@ BestCool I've tryed to write GDFS from k600i cid 36 but at 12% I receive an error (something like it cannot write at adress "xx xx xx xx xx xx xx" ...) and at 18% it stops with some other error ..... I will try again monday and post here the error messages ... can the flash be damaged ?! thank you

12-18-2005, 19:40	#10 (permalink)
BesTCooL No Life Poster Join Date: Dec 2002 Location: TURKEY Age: 44 Posts: 3,285 Member: 18442 Status: Offline Sonork: 111110 Thanks Meter: 622	U use full batery or use external power supply and downgrade baudrate use 460800 or 230400....... try again... I dont think Flash damaged...