safe unlock both K608 & K750i both cid 49
 

Plz can you give 99.99 % sure procedure for these fones.

Only unlock

Br
Ziggy

Flashing red CID49 phones:

1. Attach.
2. Unlock RSA.
3. Reattach.
4. Flash main FW and raw FS.
5. Customize FS.
6. Turn off phone.

Unlocking red CID49 phones:

1. Attach.
2. Unlock RSA.
3. Reattach and flash restore file (of the same version as main FW).
4. Direct unlock.

More procedures will be released tomorrow.

To unlock AND flash red CID49 phones:

1. Attach.
2. Unlock RSA.
3. Reattach.
4. Unlock.
5. Reattach.
6. Flash main FW and raw FS.
7. Customize FS.
8. Turn off phone.

To attach phone you may use Ctrl-A.
To turn the phone off you may use Ctrl-O.

thank you master Lead i think this should be sticky because information is complete.

The information will be extended and put to the Cruiser help file.

thx Mr. LEAD. You answered a lot of my questioned today! I will wait for the guide now, so you dont need to answer them along six hundret times...

Mr leed i flash alot of w550 red cid 49 without unlock rsa just i convert it to browen and after i finish flahing and custmoize i convert it again to red .... and work very fine ... any proplem in this way ... ?

For me the safe mode for unlock this phone now is Usb-Smart,or with Setool with tespoint .

Thanx for the very useful info Lead.
BR
Kashif Khan

This sequence has not worked, I have proven several times without success:

Flashing red CID49 phones:
1-Attach.
2-Unlock RSA.
3-Reattach.
4-Flash main FW and raw FS.
5-Customize FS.
6-Turn off phone.
------------------------------
I obtained success with this sequence:

1-Attach.
2-Unlock RSA.
3-Reattach.
4-Flash main FW and raw FS.
5-Reattach.
6-Unlock RSA.
7-Reattach and flash restore file
8-Customize FS.
9-Turn off phone.

Version 9.54 ready!
Connecting via UC-10 Universal Cable...
Powering on the phone...
Baseband chip ID: 0x7100
Protocol version: 3.1
Baudrate = 460800Bd
Unknown phone detected.
Phone CID: 26728
Phone color: Unknown
Use testpoint to boot the phone!
All threads terminated.
Connecting via UC-10 Universal Cable...
Powering on the phone...
Baseband chip ID: 0x7100
Protocol version: 3.1
Baudrate = 460800Bd
Sony Ericsson phone detected.
Phone CID: 49
Phone color: Red
Flash certificate: A1_DB2000_49_RED
Trying Red CID49 flash applet...
Sending applet prologue...
Sending applet body...
Time spent entering bootstrap: 1s
Initializing phone hardware...
Flash manufacturer: Intel
Flash ID: 0x890D
OTP Security Level: 1 (Retail)
OTP CID: 49
Sending applet...
RSA protection state cannot be determined for this CID.
Phone hardware initialized OK
Preparing to program flash...
Programming flash...
Time: 00:00:01
Flash process done.
Phone automatically detached.
Connecting via UC-10 Universal Cable...
Powering on the phone...
Baseband chip ID: 0x7100
Protocol version: 3.1
Baudrate = 460800Bd
Sony Ericsson phone detected.
Phone CID: 49
Phone color: Red
Flash certificate: A1_DB2000_49_RED
Trying Red CID49 flash applet...
Sending applet prologue...
Sending applet body...
Time spent entering bootstrap: 1s
Initializing phone hardware...
Flash manufacturer: Intel
Flash ID: 0x890D
OTP Security Level: 1 (Retail)
OTP CID: 49
Sending applet...
RSA protection state cannot be determined for this CID.
Phone hardware initialized OK
Flash file: "R5BC004_CXC1250057_GENERIC_SA.cw9sw"
Waiting for flash file to load...
Preparing to program flash...
Defeating RSA protection...
Waiting for the phone to turn off...
Should the communication hang, reinsert battery.
Baudrate = 460800Bd
Sending applet prologue...
Sending applet body...
Waiting for acknowledge...
Initializing applet...
Baudrate = 460800Bd
Identifying firmware...
Firmware ID: prgCXC1250057_GENERIC_SA
Firmware version: R5BC004
Defeated!
Sending applet...
Programming flash...
RSA protection was set back to normal.
Time: 00:00:06
Flash process done.
Sending CS applet...
Initializing CS applet...
Starting up GDFS service...
Starting up filesystem, please wait...
Building customization...
Customizing phone...
Done.
Writing CDA Article MS string...
Done.
Writing CDA Version MS string...
Done.
Writing Default Article MS string...
Done.
Writing Default Version MS string...
Done.
Writing langpack string...
Done.
Writing country...
Done.
Uploading certificates...
Certificates uploaded successfuly.

Some explanation?

please see clear the above way is for These procedures are correct for flashing CID36 or brown CID49 files to red CID49 phones!

Lead please post correct procedure for RED CID49 phones. I must upgrade and change language of a W810i.

Thanks in advance,

UnlockBR

Urgent help required for w810i
 

Hi Lead !

i got w810i , cid 49 red , i want to flash it & unlock it as well by new cruiser sw , so can u plz recomend me the best way to hanle it.

thanks

GSMSOL
UK